The Electrochemical Society was founded in 1902 to advance the theory and practice at the forefront of electrochemical and solid state science and technology, and allied subjects.
Find out more about ECS publications
Visit the ECS homepage
Number 1, January 2009
Previous issueNext issue
Open all abstracts, in this issue
Mao-Sung Wu, Rung-Hau Lee, Jiin-Jiang Jow, Wein-Duo Yang, Ching-Yuan Hsieh and Biing-Jyh Weng
Nanostructured iron oxides were electrodeposited anodically onto nickel substrate in aqueous solution at room temperature. Deposited films after annealing at 300°C are characterized as rhombohedral Fe2O3. The morphology of the porous film deposited at high current density shows nanosheets of 10–16nm in thickness. A film deposited at low current density has aggregates of nanorods. Electrochemical impedance results show that the film of randomly distributed nanosheets has a higher percentage of large pores than the film of aggregated nanorods. Consequently, specific capacitance of the film with nanosheets is higher than that of the film with aggregated nanorods at galvanostatic charge/discharge.
Amy C. Marschilok, Kenneth J. Takeuchi and Esther S. Takeuchi
Recently, there has been interest in phosphate cathodes for lithium batteries due to the excellent chemical and thermal stability of LiFePO4. Vanadium oxide bronzes have attracted attention due to silver vanadium oxide (Ag2V4O11) batteries being used as power implantable devices. We report the first investigation of silver vanadium phosphorous oxide (Ag2VO2PO4) as a cathode material in lithium cells. While the synthesis of Ag2VO2PO4 has been previously reported, this is the first exploration of its electrochemistry. The Ag2VO2PO4 material yielded 205mAh∕gto2.0V and 270mAh∕gto1.5V under constant current discharge and supported 50mA∕cm2 pulses above 1.5V.
Keryn Lian and Chang Ming Li
Asymmetrical electrochemical capacitors using heteropoly acid (HPA) electrolytes and RuO2-graphite electrodes were investigated. The fabricated devices have a working voltage window of 0–1.4V and can be discharged more efficiently than conventional symmetrical capacitors. Pseudocapacitance from HPA has enhanced the total capacitance of these devices. HPAs have been shown to be able to both function as an electrolyte and to contribute to pseudocapacitance.
Zhen-Bo Wang, Peng-Jian Zuo, Bao-Sheng Liu, Ge-Ping Yin and Peng-Fei Shi
Tungsten carbide (WC) was prepared by carbothermal synthesis in 900°C. PtNiPb catalysts with homemade WC and XC-72 carbon black as supports, respectively, were prepared. Their performances were tested through cyclic voltammetric, chronoamperometric, and current density–time curves. Electrochemical activity for methanol electro-oxidation of PtNiPb/WC catalyst is evidently higher than that of PtNiPb∕C before accelerated durability testing. Its activity is also markedly higher than that of the latter after an accelerated durability test. These results indicate that the WC as a support can improve the activity and stability of PtNiPb catalyst due to usage of WC and its stability in acidic medium.
Jeffrey A. Read and Wishvender K. Behl
Synthesis of electrochemically active carbon fluorides was achieved through the high-energy milling of graphite or carbon black with CoF3 at room temperature. The carbon fluorides were characterized by elemental analysis, X-ray diffraction, IR, and X-ray photoelectron spectroscopy. The results for the carbon fluoride powder prepared from graphite are reported here. This material, with the formula C1.6F, appears to have both semi-ionic and covalent CF bonds and demonstrates many of the characteristics of low-temperature carbon fluorides. The material has a high discharge potential of 3.2V vs Li∕Li+ and a discharge capacity in the range of 450–500mAh∕gto2.0V.
Jeng-Kuei Chang, Ming-Tsung Lee, Chi-Wei Cheng, Wen-Ta Tsai, Ming-Jay Deng and I.-Wen Sun
Development of Mn oxide supercapacitors incorporating ionic liquid (IL) electrolytes was attempted. The experimental results indicate the possibility of achieving pseudocapacitive performance of Mn oxide in ILs without involving protons and alkali cations, thus opening a route of developing electrolytes for oxide-based pseudocapacitors. In 1-ethyl-3-methylimidazolium-dicyanamide aprotic IL, Mn oxide can exhibit a specific capacitance of 72F∕g in a potential window of 2V. Due to high ionic conductivity, large electrochemical windows, excellent thermal stability, and nonflammability of the IL, a high-voltage and long-life energy storage system is successfully proposed.
Pilwon Heo, Toshihiko Harada and Takashi Hibino
Nanosized proton-conducting Sn0.95In0.05P2O7 ionomers were grown on carbon supports by the coprecipitation of tin and indium chlorides with excess ammonia water and subsequent solid-state reaction with phosphoric acid. The resulting homogeneous networks of Sn0.95In0.05P2O7 ionomers enhanced the activity of a Pt catalyst for the oxygen reduction reaction in the temperature range of 150–250°C. In addition, the Pt catalyst showed high corrosion resistance in the cathode environment while maintaining high performance levels. A comparison of the cathode performance between Sn0.95In0.05P2O7 and H3PO4 ionomers further demonstrated that the Sn0.95In0.05P2O7 nanoparticles are promising candidates for cathode ionomer materials at high temperatures.
E. Rodrigue and V. Kaajakari
We present a method to electrochemically etch crystalline quartz. Electrochemical etching has not been previously explored as a method for processing quartz because of its insulating nature. By injecting energetic charge carriers into the quartz it can be made temporarily conductive, allowing currents which will affect the chemical etch rate. This was verified by etching samples of AT-cut quartz while bombarding the sample with electrons. Etch depths were plotted as a function of current density, showing variations of ±3× the control etch rate. The ability to increase and decrease the etch rate can be used to define quartz microstructures.
Tae-Young Park, Chang-Hee Cho, Il-Kyu Park and Seong-Ju Park
We report the effect of chemical etching of p-GaN using molten KOH:NaOH solution on leakage currents, light output power, and electrostatic discharge (ESD) characteristics of GaN light-emitting diodes (LEDs). Photoluminescence and capacitance–voltage measurement indicated that a deep donor–acceptor pair (DDAP) was densely concentrated near the p-GaN surface region (∼18nm) and the defects were effectively removed by a chemical etching process, resulting in a remarkable reduction of defect-assisted leakage current on the forward and reverse bias, and improved light output power due to enhanced injection efficiency in etched GaN LEDs. The negative-voltage ESD characteristics of etched GaN LEDs were also improved due to the decrease in DDAP defects near the surface region of p-GaN.
E. J. Ruiz, R. Ortega-Borges, J. L. Jurado, T. W. Chapman and Y. Meas
Sodium percarbonate (SPC) can be produced electrochemically from aqueous Na2CO3 solution in both its 2Na2CO3⋅3H2O2 and Na2C2O6 forms simultaneously. This was achieved in a two-compartment cell separated by a cation-exchange membrane. Na2C2O6 was produced on the anodic side by water oxidation on a boron-doped diamond electrode, with anodic current efficiencies of 20–40%. On the cathodic side, SPC was synthesized from carbonate through generation of H2O2 by oxygen reduction on high-surface-area carbon felt. Cathodic current efficiency was 60% and nearly constant. The effect of Na2SiO3 as a percarbonate stabilizer was studied during electrolysis and during storage, with 4g∕L giving the best performance.
Jaakko Niinistö, Kaupo Kukli, Timo Sajavaara, Mikko Ritala, Markku Leskelä, Lars Oberbeck, Jonas Sundqvist and Uwe Schröder
Yttrium-doped HfO2 films were grown by atomic layer deposition via alternating HfO2 and Y2O3 growth cycles. Precursors used were (CpMe)2Hf(OMe)Me or Hf(NEtMe)4 and (CpMe)3Y together with ozone. The 5–8nm thick HfO2:Y films were amorphous in as-deposited state and crystallized as high-permittivity cubic∕tetragonal polymorphs upon annealing. The best combination of low leakage current of 10−7A∕cm2 at 1V and high capacitance was achieved with the films grown from Hf(NEtMe)4, with yttrium content being about 6–7 atom %. The highest permittivity values measured for these films reached 30.
Pankaj Kalra, Nikhil Vora, Prashant Majhi, P. Y. Hung, Hsing-Huang Tseng, Rajarao Jammy and Tsu-Jae King Liu
Nitrogen implantation prior to nickel silicidation is shown to result in a modified Schottky barrier height at the NiSi∕Si(001) interface. Passivation of dangling bonds at the NiSi∕Si interface to de-pin the Fermi level, axiotaxy texture, and strain-induced barrier lowering are determined to be the main mechanisms for the barrier-height modification. Significant barrier-height reduction (by as much as 0.37eV) can be achieved on n-type silicon. However, the resistivity of nickel silicide increases significantly beyond a critical nitrogen-implant dose (1×1015cm−2).
Tsung Yi Lu, Chin Meng Wang and Tien-Sheng Chao
An enhanced stress memorization-technique that utilizes a strain proximity free technique (SPFT) and a stacked-gate structure has been demonstrated by multiple strain-gate engineering. The electron mobility of n-channel metal-oxide semiconductor field effect transistors (nMOSFETs) with SPFT exhibit a 16% increase compared to that of counterpart techniques. SPFT avoids the limitation of stressor volume for performance improvement in high-density complementary metal oxide semiconductor circuits. We also found that optimization of stacked, random poly-Si-grain gate structure in combination with SPFT can improve mobility further to 22% more than a single poly-Si gate structure without SPFT.
D. Panda, S. Maikap, A. Dhar and S. K. Ray
The structural and electrical characteristics of Ni nanocrystals embedded in high-kHfO2 have been studied. High-resolution transmission electron microscopy revealed the formation of tiny Ni nanocrystals, in the average diameter of ∼8nm size for the sample annealed at 1000°C for 5min. Atomic force microscopy shows the deposition of uniform Ni nanocrystals on a HfO2 layer. A good hysteresis memory window of ∼2.1V at sweeping gate voltage of ±15V was observed in optimized annealed samples. A maximum flatband voltage shift of 2.1±0.05V was accomplished for the optimized sample. The retention and leakage current of the metal oxide semiconductor capacitors were also studied.
Po-Tsun Liu, Yi-Teh Chou and Yi-Yu Kao
Supercritical fluid (SCF) technology was proposed to improve the dielectric properties of electron-gun evaporated aluminum oxide (AlOx) film in this work. The leakage current of AlOx film deposited at room temperature was suppressed significantly from 10−4to10−10A at a bias voltage of −20V after the SCF treatment mixed with water and propyl alcohol. The evolution of the leakage conduction mechanism was confirmed theoretically from trap-assisted quantum tunneling to the Schottky emission process due to the reduction of electric traps in the AlOx dielectric film. In addition, our work demonstrated the application of SCF-treated AlOx gate dielectric to a pentacene-based thin-film transistor.
Sung Gyu Pyo and Sibum Kim
We report the effect of preplasma treatment on the film planarity and superfilling properties of the chemically enhanced metallorganic chemical vapor deposition (CEMOCVD) Cu process. The void-free superfilling in a 50nm technology scheme has made it the process of choice for copper-interconnect formation. There was dramatic improvement in homogeneity and planarity using dual-frequency preplasma treatment. The high frequency/low frequency=50∕500W in situ dual-frequency plasma treatment prior to low-temperature deposition of CH2I2-treated CEMOCVD Cu film revealed improved planarity and homogeneous superfilling performance in 0.10μm feature size.
Ying-Ying Zhang, Jungwoo Oh, Shi-Guang Li, Soon-Yen Jung, Kee-Young Park, Hong-Sik Shin, Ga-Won Lee, Jin-Suk Wang, Prashant Majhi, Hsing-Huang Tseng et al
In this article, ytterbium (Yb) incorporation into NiGe is proposed to improve the thermal stability of Ni germanide for high-performance Ge metal-oxide-semiconductor field-effect transistors (Ge MOSFETs). The Yb∕Ni∕TiN structure shows suppression of NiGe agglomeration and better surface morphology than the Ni∕TiN structure after a postgermanidation annealing of up to 550°C for 30min. It is notable that Yb atoms distribute uniformly at the top region of NiGe. NiGe agglomeration was retarded by Yb incorporation, and the thermal stability of NiGe was therefore improved.
Francis de Rege, Pengxiang Yang, Steven Grumbine, Jason Aggio, Roger Martin and Vlasta Brusic
Reaction of iodine with carbon acids with a pKa below 13 leads to iodine-containing molecules that are effective oxidants for copper while being stable and having a high solubility. The identities of these compounds and other reaction products is elucidated by the use of liquid chromatography-mass spectrometry and UV∕visible analysis. The mechanism of polishing copper with slurries containing these oxidants is examined by electrochemical experiments and shown to be similar to the oxidation of copper with iodine where a CuI film forms a weakly passivating film by dissolution and precipitation and is removed mechanically.
Kyoung-Seok Son, Tae-Sang Kim, Ji-Sim Jung, Myung-Kwan Ryu, Kyung-Bae Park, Byung-Wook Yoo, KeeChan Park, Jang-Yeon Kwon, Sang-Yoon Lee and Jong-Min Kim
Effects of plasma treatments on the back-channel of amorphous Ga2O3–In2O3–ZnO (GIZO) thin film transistors (TFTs) are compared for N2 and N2O plasma. Acceptor-like states originating from the oxygen adsorbed on the back-channel of the GIZO TFTs suppress the back-channel current by capturing the electrons in the GIZO active layer and thus shift the threshold voltage to the positive direction. It is also shown that the oxygen in a silicon oxide passivation layer reduces the back-channel current. An enhancement-mode GIZO TFT has been successfully fabricated by combining the N2O plasma treatment and the silicon oxide passivation layer.
Jen-Po Lin, Shih-Wei Chen and Jenn-Ming Wu
One effective method to improve electronic conduction of sol-gel Al-doped ZnO films is obtained by deductions from near-infrared transmittance spectra based on free electron absorption theory. By modifying the preheating procedure, the grains of Al-doped ZnO films become smaller and more defected, resulting in better electrical conductivity. The improved property as evidenced by the larger Urbach energy is attributed to the higher efficiency of hydrogen reduction due to smaller grains. The higher lattice scattering observed in the behavior of the temperature-dependent resistivity is caused by the more defected grains.
Jae Hwan Oh, Sang Kyu Kim, Jun Hyuk Cheon and Jin Jang
We have studied the effect of metal thickness for the metal-induced lateral crystallization (MILC) of a-Si on the off-state currents of poly-Si thin-film transistors (TFTs). It is found that they decrease with decreasing the Ni thickness for MILC. The Ni-MILC poly-Si TFT with the Ni area density of 1.4×1014cm−2 exhibited a field-effect mobility of 53.5cm2∕Vs and minimum leakage current of 0.44pA∕μm at Vds=−10V. However, the off-state current is 6.6pA∕μm when the Ni density is 9.2×1015cm−2, corresponding to the average Ni thickness of 10Å. It is concluded that the average Ni thickness for MILC should be less than 0.79Å to have low off-state currents from our experimental data.
Dong-Seok Leem, Sei-Yong Kim, Jang-Joo Kim, Mei-Hsin Chen and Chih-I Wu
We investigated the electrical properties and charge transport mechanisms of a rubidium-carbonate (Rb2CO3)-doped 4,7-diphenyl-1,10-phenanthroline (Bphen) electron transporting layer (ETL). The electron-only devices and photoemission spectroscopy analysis revealed that the formation of doping-induced gap states dominantly contributes to the improvement of carrier transport characteristics of the doped system. High-efficiency green phosphorescent p-doping/intrinsic/n-doping (p-i-n) organic light emitting diodes were demonstrated using the Rb2CO3-doped Bphen ETL and rhenium oxide (ReO3)-doped N,N′-diphenyl-N,N′-bis(1,1′-biphenyl)-4,4′-diamine hole transporting layer, exhibiting an external quantum efficiency of 19.2%, power efficiency of 76lm∕W, and low operation voltage of 3.6V at 1000cd∕m2.