Advanced LSI processing and materials science
04CA01
Shinji Migita, Yukinori Morita, Meishoku Masahara and Hiroyuki Ota
Junctionless field-effect transistors (JL-FETs) with a 3 nm channel length are fabricated on silicon-on-insulator (SOI) substrates using simple process techniques. The anisotropic etching of Si crystals by alkaline solution is utilized to form V-grooves and to define nanometer-scale channel structures. Ultrathin channels created on the SOI have a 3 nm channel length that is determined by the edge of V-grooves. Dopants are introduced by ion implantation at the source and drain regions and diffused into the channel region at a high temperature and by long-period annealing. V-groove JL-FETs thus fabricated show superior performances by scaling the thickness of the SOI channel toward 1 nm and less. Through the measurement of many V-groove JL-FETs and a simulation study, it is clarified that the management of channel thickness with atomic-scale precision is indispensable for sub-10 nm FETs.
04CA02
Anabela Veloso, Soon Aik Chew, Yuichi Higuchi, Lars-Åke Ragnarsson, Eddy Simoen, Tom Schram, Thomas Witters, Annemie Van Ammel, Harold Dekkers, Hilde Tielens et al
This work reports on aggressively scaled replacement metal gate, high-k last devices (RMG-HKL), exploring several options for effective work function (EWF) engineering, and targeting logic high-performance and low-power applications. Tight low-threshold voltage (VT) distributions for scaled NMOS devices are obtained by controlled TiN/TiAl-alloying, either by using RF-physical vapor deposition (RF-PVD) or atomic layer deposition (ALD) for TiN growth. The first technique allows optimization of the TiAl/TiN thicknesses at the bottom of gate trenches while maximizing the space to be filled with a low-resistance metal; using ALD minimizes the occurrence of preferential paths, at gate sidewalls, for Al diffusion into the high-k dielectric, reducing gate leakage (JG). For multi-gate fin field-effect transistors (FinFETs) which require smaller EWF shifts from mid-gap for low-VT: 1) conformal, lower-JG ALD-TiN/TaSiAl; and 2) Al-rich ALD-TiN by controlled Al diffusion from the fill-metal are demonstrated to be promising candidates. Comparable bias temperature instability (BTI), improved noise behavior, and slightly reduced equivalent oxide thickness (EOT) are measured on Al-rich EWF-metal stacks.
04CA03
Anabela Veloso, Soon Aik Chew, Tom Schram, Harold Dekkers, Annemie Van Ammel, Thomas Witters, Hilde Tielens, Nancy Heylen, Katia Devriendt, Farid Sebaai et al
In this work we provide a comprehensive evaluation of a novel, low-resistance Co–Al alloy vs W to fill aggressively scaled gates with high aspect-ratios [gate height (Hgate) ∼50–60 nm, gate length (Lgate) ≥20–25 nm]. We demonstrate that, with careful liner/barrier materials selection and tuning, well-behaved devices are obtained, showing: tight gate resistance (Rgate) distributions down to Lgate∼20 nm, low threshold voltage (VT) values, comparable DC and bias temperature instability (BTI) behavior, and improved RF response. The impact of fill-metals intrinsic stress, including the presence of occasional voids in narrow W-gates, on devices fabrication and performance is also explored.
04CA04
Leonid Bolotov, Koichi Fukuda, Hiroshi Arimoto, Tetsuya Tada and Toshihiko Kanayama
Quantitative evaluation of the dopant concentration across silicon p–n junctions has been performed on oxide-passivated surfaces by using tunneling current mapping in the constant-gap mode of a multimode scanning probe microscope (MSPM). A distinct difference between regions with different impurity concentrations was observed in tunneling current maps when a constant tunneling gap was maintained by using repulsive force acting on the MSPM probe. To extract impurity profiles, the results of three-dimensional device simulations within the current continuity model were compared with measured bias-dependent current profiles. The obtained impurity profiles showed agreement with the actual donor concentration in the p–n junction region. The results demonstrate the applicability of the method for quantitative analysis of the local impurity distribution in modern semiconductor devices with improved sensitivity and nanometer spatial resolution.
04CA05
Daisuke Kosemura, Motohiro Tomita, Koji Usuda, Tsutomu Tezuka and Atsushi Ogura
Anisotropic biaxial stress states in Si1-xGex/Si mesa structures were evaluated by oil-immersion Raman spectroscopy. Using a high-numerical-aperture lens, the electrical field component perpendicular to the surface, i.e., z-polarization, can be obtained. The z-polarization enables the excitation of the forbidden optical phonon mode, i.e., the transverse optical (TO) phonon mode, even under the backscattering geometry from (001)-oriented diamond-type crystals. The anisotropic biaxial stress evaluation of Si1-xGex was considered difficult compared with that of Si, because many unknown parameters exist for Si1-xGex, e.g., phonon deformation potentials (PDPs), the Ge concentration x, and the factor of Raman shift on x. In this study, PDPs and the Ge concentration in Si1-xGex were investigated in detail. As a result, using precise PDPs and x, a clear dependence of anisotropic biaxial stress states in Si1-xGex on the mesa structure shape was observed.
04CA06
Motohiro Tomita, Masaya Nagasaka, Daisuke Kosemura, Koji Usuda, Tsutomu Tezuka and Atsushi Ogura
A strained SiGe layer will be used in next-generation transistors to improve device performance along with device scaling. However, the stress relaxation of the SiGe layer may be inevitable in nanodevices, because the SiGe layer is processed into a nanostructure. In this study, we evaluated the anisotropic stress relaxation in mesa-shaped strained SiGe layers on a Si substrate by electron backscattering pattern (EBSP) measurement. Moreover, we compared the results of EBSP measurement with those of anisotropic Raman measurement and finite element method (FEM) simulation. As a result, the anisotropic stress relaxation obtained by Raman spectroscopy was confirmed by EBSP measurement. Additionally, we obtained a good correlation between the results of EBSP measurement and FEM simulation. The σxx and σyy stresses were markedly relaxed and the σzz and σxz stresses were concentrated at the SiGe layer edges. These stresses were mostly relaxed in the distance range from the SiGe layer edges to 200 nm. Therefore, in a SiGe nanostructure with a scale of less than 200 nm, stress relaxation is inevitable. The results of EBSP and Raman measurements, and FEM simulation show a common tendency. We believe that EBSP measurement is useful for the evaluation of stress tensors and is complementary to Raman measurement.
04CA07
Bong-Su Jo, Ho-Jung Kang, Sung-Min Joe, Min-Kyu Jeong, Kyung-Rok Han, Sung-Kye Park, Byung-Gook Park and Jong-Ho Lee
We characterized normalized noise power density (SI/IBL2) and bit-line (BL) current fluctuation (ΔIBL) using traps generated applying cycling stress in 26 nm NAND flash memory. The ΔIBL, SI/IBL2, and capture (τc) and emission times (τe) of random telegraph noise (RTN) were measured before and after cycling stress, respectively. With cycling stress, traps were generated, and SI/IBL2 and ΔIBL were increased significantly. The τc and τe of RTN after cycling stress are similar with to those before cycling stress. RTN was characterized in terms of the trap position in the three-dimensional space (xT, yT, and zT) of the tunneling oxide and trap energy (ET). three-dimensional technology computer-aided design (TCAD) simulation was used to determine the position of zT through the effect of adjacent BL cells.
04CA08
Kimihiko Kato, Shigehisa Shibayama, Mitsuo Sakashita, Wakana Takeuchi, Noriyuki Taoka, Osamu Nakatsuka and Shigeaki Zaima
We have investigated the impacts of the oxygen radical process on the interfacial structures and electrical properties of Al2O3/Ge structures to clarify the interfacial reaction mechanisms. At a low process temperature, the oxygen radical process can introduce oxygen atoms to the Al2O3/Ge interface without a thermally activated process in spite of the high barrier property of the oxygen diffusion for the Al2O3 layers. In addition, the oxygen radical process at a low process temperature can relatively suppress the diffusion of Ge atoms from the Ge substrate or GeO molecules from the Al2O3/Ge interface to the surface of the Al2O3 layer. However, at a high process temperature, Ge atoms and/or GeO molecules actively diffuse into the Al2O3 layer during the oxygen radical process as well as the O2 thermal annealing, and the diffusion changes the depth distribution of Ge oxides in the Al2O3/Ge structure. From the analysis of the electrical properties of MOS capacitors, the interface state density (Dit) of the Al2O3/Ge structure decreases not with increasing thickness of the Ge oxide interlayer but with the amount of Ge oxide near the Al2O3/Ge interface. The increase in the amount of the Ge oxide distributed in the Al2O3 layer induces the increase in the capacitance equivalent thickness (CET). The diffusion of Ge into the Al2O3 layer with a high process temperature causes the unexpected increase in CET. Therefore, the oxygen radical process at low temperature effectively decreases Dit of Al/Al2O3/Ge MOS capacitors without increasing CET.
Advanced interconnect/interconnect materials and characterization
04CB01
Ken Suzuki, Naokazu Murata, Naoki Saito, Ryosuke Furuya, Osamu Asai and Hideo Miura
The relationship between the electrical properties and crystallographic quality (crystallinity) of electroplated copper thin-film interconnections was investigated. The crystallinity of the grains and grain boundaries of the interconnections was evaluated on the basis of the image quality (IQ) value obtained by electron back-scatter diffraction (EBSD) analysis. The electrical properties of the interconnections vary markedly depending on their crystallinity. The crystallinity also changed markedly as functions of electroplating conditions and the annealing temperature after electroplating. Although the electro migration (EM) resistance of the annealed interconnection was improved, stress-induced migration (SM) was activated by a high residual stress after annealing. To improve electrical reliability without heat treatment after electroplating, the effects of the seed layer under the interconnections on the crystallinity were investigated. As a result, the crystallinity was improved by changing the seed layer from Cu to Ru. In addition, the decrease in current density during electroplating also improved the crystallinity. Therefore, both introducing the Ru seed layer and decreasing the current density during electroplating are effective for developing highly reliable copper interconnections.
04CB02
Sten Vollebregt, Ann N. Chiaramonti, Johan van der Cingel, Kees Beenakker and Ryoichi Ishihara
Carbon nanotubes (CNT) can be an attractive candidate for vertical interconnects (vias) in three-dimensional integrated circuits due to their excellent thermal and electrical properties. To investigate the electrical resistivity of CNT, test vias were fabricated using both a top-down and bottom-up approach. The measured resistivity for the top-down process of 10 mΩ cm is among the better values found in literature. Beside this, the ability to grow CNT directly on single-grain thin-film transistors (SG-TFT) was demonstrated. The electrical performance of the SG-TFT was found not to be influenced by the CNT growth.
04CB03
Ruey-Lue Wang, Chao-Jung Chen, Yu-Ru Lin, Pin-Yi Liu, Yan-Kuin Su and Ting-Jen Hsueh
In this paper, spiral inductors on high-resistivity silicon (HR-Si) substrates, which surfaces were passivated by different process methods, were fabricated and measured. The comparison of inductances and quality factors between these inductors shows that the inductances and quality factors of spiral inductors significantly depend on process method and thickness of surface passivation layer. The differently generated passivation layer results in different effective substrate resistivity and hence gives rise to different substrate loss. The experimental results show that using thicker nanocrystalline silicon (nc-Si) as a passivation layer will result in a smaller substrate loss and hence spiral inductors on the substrate have larger inductances and larger quality factors. In this study, the metal thickness of inductors is 1.2 µm and is about half that of the inductors provided by foundries. At higher frequencies, the thinner spiral inductors on the SiO2/nc-Si/HR-Si substrate have larger inductances and larger quality factors as compared with the inductors provided by foundries. With the same metal thickness as that adopted in standard processes of foundries, the identical-geometry inductors on the SiO2/nc-Si/HR-Si substrate probably exhibit superior quality factors.
04CB04
Kazuyoshi Ueno, Yusuke Karasawa, Satoru Kuwahara, Shotaro Baba, Hitoshi Hanai, Yuichi Yamazaki, Naoshi Sakuma, Akihiro Kajita and Tadashi Sakai
Multilayer graphene (MLG) is expected to be a low-resistance and high-reliability interconnect material replacing copper (Cu) in nanoscale interconnects. Chemical vapor deposition (CVD) on catalytic metals is expected as a practical method for MLG deposition. To obtain high-quality MLG films without catalyst agglomeration by CVD, heat-resistant Co–W catalytic metals were investigated. The agglomeration of the Co–W catalytic metals was suppressed by increasing the W composition; however, MLG deposition was suppressed at the same time. The effects of W addition on the MLG growth were discussed from the viewpoints of the crystallographic change of the Co–W catalysts and chemical reactions. It was found that the Co grain size was reduced and the fcc Co formation was suppressed by W addition. In addition, graphite formation was supposed to be suppressed by W addition owing to the formation of phases other than fcc Co according to the Co–W–C phase diagram. With the optimum W concentration, MLG crystallinity was improved by high-temperature CVD using the heat-resistant Co–W catalytic metals (0.7 at. %) without agglomeration, compared with that in the case of using pure-Co catalysts.
04CB05
Kozo Koiwa, Masaki Omiya, Nobuyuki Shishido, Shoji Kamiya, Hisashi Sato, Masahiro Nishida, Takashi Suzuki, Tomoji Nakamura, Toshiaki Suzuki and Takeshi Nokuo
A novel scheme for the evaluation of interface adhesion energy was examined by a detailed numerical simulation of interface crack extension. The effects of crystal orientation on the Cu/SiN interface adhesion strength of LSI was evaluated using the finite element method. Crack extension simulation was conducted with a model of the actual specimen used for the interface fracture test. The characteristics of elastic–plastic deformation, which changes significantly depending on crystal orientation, were taken into account in the model. With this scheme, the effect of orientation of single crystals on the maximum load Pmax was investigated under the condition of a constant bonding energy of the interface at the beginning of unstable crack propagation during the fracture test. The values of Pmax obtained with a number of different crystal orientations ranged over 179–311 µN. The result indicates that the crack propagates more easily in the case that slip deformation of Cu near the interface starts with a low stress, as in the case of the (111) surface. It implies that the apparent interface adhesion strength represented by the load required to debond the interface strongly depends on Cu crystal orientation, because the amount of energy used for plastic deformation of the Cu crystal changes with crystal orientation near the interface.
04CB06
Akio Kawabata, Tomo Murakami, Mizuhisa Nihei and Naoki Yokoyama
We have grown an extremely dense nanocarbon structure on a Si substrate at a temperature of 450 °C, in which vertical graphene layers were formed densely below horizontal graphene layers. We named this carbon structure “dense, vertical, and horizontal graphene (DVHG)”. The density of this structure was an extremely high at 1.4 g/cm3, which is 63% of that of graphite (2.2 g/cm3). Although DVHG showed poor thermal properties, we confirmed that vertical thermal conductivity increased by a factor of 10 by removing the horizontal graphene layers from the top of DVHG. This result indicates that the thermal conductivity parallel to the graphene plane is several orders of magnitude higher than that perpendicular to the graphene plane.
04CB07
Motonobu Sato, Makoto Takahashi, Haruhisa Nakano, Takayuki Muro, Yuji Takakuwa, Shintaro Sato, Mizuhisa Nihei and Naoki Yokoyama
We fabricated multilayer graphene directly on SiO2 by annealing of sputtered amorphous carbon under a catalyst layer without complicated transfer processes, and investigated the effects of the catalysts and the annealing ambient gases on obtaining large-grain, multilayer graphene. As a result, it was found that annealing conditions with a Co catalyst layer in a nitrogen gas atmosphere are important for increasing the ratio of oriented graphene sheets, corresponding to a lower resistivity of the film. Furthermore, it was confirmed that the multilayer graphene wire obtained by optimizing the growth conditions can sustain a high current density of 107 A/cm2, that is, the lifetime of the multilayer graphene wire is over two orders of magnitude longer than that of a Cu wire with the same current density; this current density is over one order of magnitude higher than the current density that can be carried by a Cu wire for the same lifetime.
04CB08
Bui Thanh Tung, Motohiro Suzuki, Fumiki Kato, Shunsuke Nemoto, Naoki Watanabe and Masahiro Aoyagi
High-precision integration has valuable meaning in heterogeneous convergent technology. In this paper we report on a new high-precision low-temperature bonding approach, capable of submicron alignment accuracy, based on the conventional ultrasonic flip-chip bonding technique and modified metal pad and bump elements. The interconnection pair made from a conductive-sloped hollow bonding pad (concave) and metal cone bump (convex) elements, i.e., misalignment self-correction elements, helps in aligning and maintaining the alignment between the chip and the substrate during stacking. By this method, the stacking accuracy can be improved significantly and effectively. Repeatable submicron (i.e., less than 500 nm) bonding accuracies are confirmed through experimental investigation. Moreover, reliable bond characteristics including electrical and mechanical properties are observed, validating the performance of the bonding approach. With these results, the proposed high-precision low-temperature bonding approach shows its suitability for heterogeneous electronics–optics integration applications.
04CB09
Yuka Ito, Takafumi Fukushima, Kang-Wook Lee, Koji Choki, Tetsu Tanaka and Mitsumasa Koyanagi
To establish liquid-assisted assembly processes applicable to heterogeneous system integrations, we present flip-chip self-assembly of dies with Cu/Sn microbumps using the difference in droplet wetting between hydrophilic and hydrophobic areas. Flip-chip self-assembly is assisted by a water-soluble flux that has high surface tension comparable to that of pure water and contains an additive of a reducing agent for metal oxides. Control of the additive concentration in the flux provides high wettability contrast that enable spontaneous and precise alignment of chips to hydrophilic areas formed on substrates within 5 µm in alignment accuracy. In the subsequent chip bonding process, the reductant can eliminate the metal oxide layer and improve the solder wettability of Sn to the corresponding electrode pads formed on the chips. In addition, we confirm, through electrical characteristic evaluation after thermal compression bonding, that the resulting daisy chain formed between the substrates and self-assembled chips with the flux shows sufficiently low contact resistance of below 20 mΩ/bump without disconnection.
04CB10
Lijing Qiu, Akihiro Ikeda, Kazuhiro Noda, Seiya Nakai and Tanemasa Asano
Room-temperature Cu–Cu bonding was realized by applying ultrasonic vibration together with compression force to the bonding of a cone-shaped bump. The size of the bump was about 10 µm. The connection pitch was 20 µm. Mechanical characterization showed that the bonding strength increases with vibration amplitude and depends on the thickness of the counter electrode made of Cu. The thickness dependence of the bonding strength was found to be caused by an increase in the surface roughness of the counter electrode. It was shown that the bonding strength meets the requirement from application to products. Electrical characterization using a daisy-chain connection test demonstrated that more than 10,000 pins on a chip can be connected with a sufficiently low resistance.
04CB11
Hisashi Kino, Ji Choel Bea, Mariappan Murugesan, Kang Wook Lee, Takafumi Fukushima, Mitsumasa Koyanagi and Tetsu Tanaka
A three-dimensional LSI (3D-LSI) that vertically stacks Si chips with a number of through-silicon vias (TSVs) and metal microbumps has attracted much attention recently. However, there are some issues to be resolved in the fabrication of 3D-LSI. In this study, we investigated impacts of local bending stress on the performance of a complementary metal–oxide–semiconductor (CMOS) circuit fabricated in a thinned Si chip. First, we proposed a novel method and a test structure to easily induce the local bending stress in the thinned Si chip. Then, we evaluated the distribution of the local bending stress and its effects on the electrical characteristics of metal–oxide–semiconductor field-effect transistor (MOSFETs). As a result, we observed the degradations of the MOSFET currents and CMOS inverter switching behaviors in accordance with the chip local bending. Our experimental results obviously indicate that the local bending stress caused large fluctuations in the performance of the circuit fabricated in the thinned Si chip.
CMOS devices/device physics
04CC01
Geert Eneman, An De Keersgieter, Liesbeth Witters, Jerome Mitard, Benjamin Vincent, Andriy Hikavyy, Roger Loo, Naoto Horiguchi, Nadine Collaert and Aaron Thean
The interaction between two stress techniques, strain-relaxed buffers (SRBs) and epitaxial source/drain stressors, is studied on short, Si1-xGex- and Ge-channel planar transistors. This work focuses on the longitudinal channel stress generated by these two techniques. Unlike for unstrained silicon-channel transistors, for strained channels on top of a strain-relaxed buffer a source/drain stressor without recess generates similar longitudinal channel stress than source/drain stressors with a deep recess. The least efficient stress transfer is obtained for source/drain stressors with a small recess that removes only the strained channel, not the substrate underneath. These trends are explained by a trade-off between elastic relaxation of the strained-channel during source/drain recess and the increased stress generation of thicker source/drain stressors. For Ge-channel pFETs, GeSn source/drains and Si1-xGex strain-relaxed buffers are efficient stressors for mobility enhancement. The former is more efficient for gate-last schemes than for gate-first, while the stress generated by the SRB is found to be independent of the gate-scheme.
04CC02
Tomoko Mizutani, Yoshiki Yamamoto, Hideki Makiyama, Toshiaki Iwamatsu, Hidekazu Oda, Nobuyuki Sugii and Toshiro Hiramoto
The variability of subthreshold swing (SS) in fully depleted (FD) silicon-on-thin-buried-oxide (SOTB) MOSFETs is statistically analyzed and compared with that of conventional bulk MOSFETs. It is newly found that SS variability is small enough in deep subthreshold region (small drain current Ids) while it increases as increasing Ids. The mechanisms of this behavior is intensively investigated and it is found that the increase in SS variability is caused by current-onset voltage (COV) variability that is due to random dopant fluctuation (RDF). Since SOTB FETs have small COV variability thanks to an intrinsic channel, SS variability is much smaller than bulk FETs, which is a great advantage of FD SOTB in terms of Ion/Ioff ratio.
04CC03
Tsunaki Takahashi, Nobuyasu Beppu, Kunro Chen, Shunri Oda and Ken Uchida
The self-heating effects (SHEs) of bulk and silicon-on-insulator (SOI) fin-type field-effect transistors (FinFETs) and their impacts on circuit performance have been investigated on the basis of a realistic thermal conductivity of silicon. The heat dissipation via interconnect wires and interface thermal resistance in the high-κ gate stack were incorporated in simulations. It is shown that the depth of the shallow trench isolation (STI) of bulk FinFETs cannot be decreased to less than 100 nm owing to the increase in off-state leakage current. We observed that the thermal resistance Rth of SOI FinFETs greatly decreases upon thinning the buried oxide (BOX) layer. When the BOX thickness tBOX is less than 50 nm, the Rth of SOI FinFETs is smaller than that of bulk FinFETs with an STI thickness of 100 nm, indicating a lower operation temperature of the thin-BOX SOI FinFETs than that of bulk FinFETs. The lower operation temperature of the 5-nm BOX SOI FinFET was confirmed under a practical bias condition for analog operations. In fin width, Wfin, versus Rth characteristics, a strong Wfin dependence of Rth was observed only in the bulk FinFETs, implying that fluctuations in Wfin result in the variability of the operation temperature of the bulk FinFETs. Analog performance has been analyzed by calculating the cutoff frequency fT and the maximum oscillation frequency fmax. We demonstrated that both fT and fmax can be maximized in SOI FinFETs by optimizing tBOX with regard to electrical and thermal properties. Better analog performance, and hence the optimization of tBOX, are indispensable for the device design of a FinFET-based system-on-a-chip (SoC) platform.
04CC04
Young Jun Yoon, Seongjae Cho, Jae Hwa Seo, In Man Kang, Byung-Gook Park and Jung-Hee Lee
In this work, a high-performance compound semiconductor tunneling field-effect transistor (TFET) based on germanium (Ge)/gallium arsenide (GaAs) heterojunction with a tunneling-boost layer is investigated. The tunneling-boost layer in the source-side channel alters the energy band-gap structure between the source and the channel, which affects current drivability considerably. It is shown that controlling the lengths of the boosting layer (thin n+ GaAs layer) and lightly doped p-type channel (p-GaAs) also has substantial effects on adjusting Vth without complications arising from shifting metal workfunction. Furthermore, we evaluate device performances such as on-state current (Ion), subthreshold swing (S), intrinsic delay time (τ), and cut-off frequency (fT). The proposed TFET with an n-GaAs length of 12 nm showed an S of 27 mV/dec and approximately 3 times higher Ion than that of the device without a boosting layer. Moreover, it is confirmed from the extracted excellent radio-frequency (RF) parameters that the proposed device is suitable for RF applications.
04CC05
Tomohisa Mizuno, Juria Takehi, Youhki Abe and Hiromu Akamatsu
We have experimentally studied a new H+-ion-induced relaxation technique for compressive-strained SiGe layers on a buried oxide layer (BOX) for high-performance p-channel source heterojunction devices, to improve the crystalline quality of the ion-implanted SiGe layers, using the very steep recoil energy ER distribution of H+ ions. In addition, we have compared the H+-ion-induced relaxation phenomena of the strained SiGe with the O+-ion-induced one. We have experimentally shown that the strained SiGe layers can also be fully relaxed even by H+ ion implantation, using Raman spectroscopy analysis. In addition, the obtained Raman spectroscopy data show that the crystalline quality of H+-ion-implanted SiGe layers can be improved and is much more uniform, compared with that of the O+-ion-implanted area, as expected. However, high-dose H+ ion implantation locally causes the splitting of strained SiGe layers from the BOX layer, which is the technical limitation of H+ ions.
04CC06
Jie Hong, Yandong He, Ganggang Zhang and Xing Zhang
This paper presents a test circuit which can be used to analyze the p-MOSFET threshold voltage (VT) shift and fluctuation. The proposed circuit includes two p-MOSFETs, series connection. Using the circuit, we can directly measure threshold voltage shift on the output side and gather fluctuation statistics of p-MOSFET devices. The principle and the sensitivity of this method are demonstrated, followed by simulation and experimental results. A predictive model of negative bias temperature instability (NBTI) is introduced to analyze the PMOS degradation under constant stress. The NBTI stress experimental results have shown that this circuit can monitor NBTI degradation accurately, and offer a significant improvement in efficiency over existing Id–Vg methods.
04CC07
Chin-Rung Yan, Jone F. Chen, Chung-Yi Lin, Hao-Tang Hsu, Yu-Jie Liao, Min-Ti Yang, Chih-Yuan Chen, Yin-Chia Lin and Huei-Haurng Chen
Characteristics of lateral diffused metal–oxide–semiconductor (LDMOS) transistors with gradual junction profile by self-alignment implant through dual thicknesses of screen oxide are presented in this letter. Compared with LDMOS transistors with traditional junction profile, this new device shows improved off-state breakdown voltage, less severe in Kirk effect, and wider electrical safe operating area; without sacrificing device drivability. Technology computer aided design (TCAD) simulation results reveal that this new device has smaller electric field both in off- and on-state bias conditions. Hot-carrier induced degradation of this new device under various stress conditions is also investigated and compared with that of the device with traditional junction profile.
04CC08
Ke Mao, Takuya Saraya and Toshiro Hiramoto
In this paper, we report the direct measurement of intrinsic carrier mobility in “single”-silicon-nanowire metal–oxide–semiconductor field-effect transistors (MOSFETs) for the first time. To obtain intrinsic carrier mobility with high accuracy by the split capacitance–voltage (C–V) method, ultralong single-silicon-nanowires, instead of multiple parallel nanowires, were designed and fabricated. The open-circuit method was utilized to remove the parasitic effect in measured capacitance. It is found that, although mobility degradations in narrower nanowires are seen in both electrons and holes, the hole mobility is higher than the universal mobility on the (100) surface even in a “single”-nanowire thanks to the high hole mobility on the (110)-oriented side surface of the [110]-directed nanowire. The extracted mobility indicates that surface orientation plays a key role in nanowire mobility.
04CC09
Kang Liang Wei, Xiao Yan Liu and Gang Du
Using full three-dimensional (3D) technology computer-aided design (TCAD) simulations, we present a comprehensive statistical study on the random discrete dopant (RDD) induced variability in state-of-the-art intrinsic channel trigate MOSFETs. This paper is focused on the RDD variability sources that are introduced by dopant diffusion from highly doped source/drain (S/D) regions into the undoped channel region, which is referred to as junction nonabruptness (JNA). By considering a realistic lateral doping profile in the channel and evaluating the impact of JNA on the variability of performance parameters such as threshold voltage (Vth), subthreshold slope (SS), drain-induced barrier lowering (DIBL), on current (Ion), and off current (Ioff), we show that the effect of JNA can lead to substantial device variations. The nonnegligible influence of JNA puts limitations on device scaling, which is also investigated in this paper.
04CC10
Anabela Veloso, An De Keersgieter, Marc Aoulaiche, Malgorzata Jurczak, Aaron Thean and Naoto Horiguchi
In this work we explore the use of extension-less doping schemes for fully-depleted devices [two-dimensional (2D): ultra-thin body and buried-oxide layer (BOX) planar devices (UTBB); three-dimensional (3D): multi-gate field-effect transistor devices with the conduction channels wrapped around silicon (Si) fins (FinFETs) and built on bulk-Si or silicon-on-insulator (SOI) substrates], suitable for advanced logic, memory and dense circuit applications. We demonstrate that by using Si epitaxial raised source (S)/drain (D) (SEG) followed by highly doped drain (HDD)-only implantations (I/I), or by using doped-SEG and no I/I: 1) lower off-state current (IOFF) and drain induced barrier lowering effect (DIBL); 2) steeper sub-threshold slope (SS); 3) higher on-state/off-state currents ratio (ION/IOFF); and 4) higher retention times [for floating body random-access memory (FBRAM) on UTBB] can be obtained, while reducing cost and cycle time with less critical I/I photos. SEG facet formation can be controlled by the spacers shape and epi pre-clean step and its impact on device characteristics for logic and FBRAM applications is also analyzed.
04CC11
Ke Mao, Takuya Saraya and Toshiro Hiramoto
In this paper, the effects of side surface roughness on mobility behaviors in single-silicon-nanowire metal–oxide–semiconductor field-effect transistors (MOSFETs) are discussed on the basis of intrinsic carrier mobility data obtained by direct split capacitance–voltage (C–V) method measurement for the first time. To investigate the mechanisms that dominate the mobility degradation in narrower nanowires, low-temperature measurements are performed. It is found that phonon scattering has little dependence on nanowire width, indicating that the mobility degradation in our tri-gate nanowire MOSFETs is caused by surface roughness scattering. It is also found by analyzing the nanowire width dependence of mobility that the process-induced roughness on the side surface is the main source of mobility degradation in nanowire pFETs, while the degradation caused by the side surface roughness is negligible in nanowire nFETs.
04CC12
Teruyuki Ohashi, Shunri Oda and Ken Uchida
The impact of deformation potential increase at metal–oxide–semiconductor (MOS) interfaces on stress effects is thoroughly studied. In our previous study, we revealed that the deformation potential (Dac) of Si increases at MOS interfaces. The energy split between two- and four-fold valleys is proportional to Dac. Therefore, it is considered that the Dac increase at MOS interfaces has an affect on strain effects. Dac effectively changes by adjusting Si-on-insulator (SOI) thickness and carrier distribution at MOS interfaces. Therefore, the SOI thickness dependence and carrier distribution dependence of electron mobility enhancement ratio (Δµe/µe) under strain are investigated. Experimental results are explained by the model including the Dac increase at MOS interfaces. In addition, experimental data are well reproduced by calculation using the position-dependent-Dac model. By applying uniaxial strain, effective mass, subband occupation, and intervalley scattering rate are also changed. Their effects on Δµe/µe are also discussed in this paper.
04CC13
Tomohisa Mizuno, Takashi Aoki, Yuhsuke Nagata, Yuhta Nakahara and Toshiyuki Sameshima
We have experimentally studied the surface orientation/strain effects on quantum mechanical confinement (QMC) in two-dimensional (2D) Si layers with thicknesses less than the Si lattice constant for future metal–oxide–semiconductor (MOS) devices. By UV–Raman spectroscopy, we have demonstrated that the quantum phonon confinement effects (PCEs) rapidly increase with decreasing 2D Si thickness TS, but is almost independent of surface orientation and strain. Thus, electron saturation velocity of the 2D Si is degraded by the reduced phonon energy owing to the PCEs. On the other hand, photoluminescence (PL) emitted from the only (100)-surface 2D Si layers, depends on the excitation photon energy hν (2.33≤hν≤3.81 eV), and PL intensity increases with decreasing TS. The PL data can be explained by simple PL models considering the electron/hole pair recombination mechanism. Consequently, it is necessary to reconstruct the device design for future Si devices, considering the TS dependence of the 2D Si properties.
04CC14
Kyung Rok Kim, Sunhae Shin, Seongjae Cho, Jung-Hee Lee and In Man Kang
In this work, we present a novel analytical method based on radio-frequency (RF) analysis for the accurate and reliable extraction of source and drain (S/D) series resistances in silicon nanowire (SNW) metal–oxide–semiconductor field-effect transistors (MOSFETs). The proposed method provides decomposed RF model equations for the gate-bias-independent off-state and gate-bias-dependent on-state components from both Y- and Z-parameters. The validity of our extraction method for S/D series resistances in SNW MOSFETs has been carefully tested in comparison with that of a previously reported method as well as with the physical three-dimensional (3D) device simulation. The schematically modeled Y- and Z-parameters have demonstrated excellent agreement with the numerical 3D device simulation results for various SNW MOSFET structures up to the 100 GHz frequency regime.
04CC15
Takashi Kato, Taiki Uemura, Hiroko Mori, Yoshihiro Ikeda, Kaina Suzuki, Shigeo Satoh and Hideya Matsuyama
Accelerated neutron tests for soft error rate (SER) are carried out using unbalanced feedback-loop circuits fabricated by Si and embedded SiGe (eSiGe) processes. The contribution of the p-type metal–oxide–semiconductor field effect transistor (PMOS) to total SER is shown to substantially decrease in the eSiGe process. The characteristics of parasitic bipolar transistors in PMOSs with and without eSiGe are investigated using technology computer-aided design (TCAD) simulations. We find that the narrow band gap of SiGe causes an increase in the rate of electron flow from the well region (Si) to the source region (SiGe), leading to a decrease in the current gain of the parasitic bipolar transistor in PMOS with eSiGe. Our results indicate that eSiGe can be attributed to the suppression of the parasitic bipolar effect, resulting in a reduced contribution of PMOS to SER.
04CC16
Te Liang Lee, Ming Tsang Tsai, Ya Chin King and Chrong Jung Lin
In this paper, a novel sub-20 V device which is called contact gate MOSFET (CGMOS) with fully CMOS logic compatible process is proposed and demonstrated. Comparing with lateral double diffusion MOSFET (LDMOS), CGMOS uses P substrate instead of N minus layer as drift region in logic process, and a contact on resistance protection oxide (RPO) layers to form an extra gate on the drain side of the channel region to provide a better gate control and reduce the surface field. This new device significantly rises up the breakdown voltage to 18 V with specific on-resistance 8.8 mΩ·mm2 in a small high voltage (HV) MOSFET area. Since there is no extra mask for creating the drift region or additional step for the wire bonding, CGMOS makes the integration of high voltage and logic circuits much simpler and area-saving.
04CC17
Xixiang Feng, Weiling Kang, Qi Cheng and Yijian Chen
An analytic current–voltage (I–V) model for doped double-gate metal–oxide–semiconductor field-effect transistors (MOSFETs) is derived by using a rigorous perturbation method to solve one-dimensional (1D) Poisson's equation. More accurate prediction of the surface potential and I–V characteristics is achieved by introducing a higher-order correction and setting the operating point of Taylor expansion at the channel surface where the major population of mobile charge is located. Both technology computer-aided design (TCAD) simulations and the numerical solution to 1D Poisson's equation verify the improved accuracy of our model compared with Berkeley short-channel insulated-gate FET model (BSIM) model, especially when the gate voltage and doping level are higher. We also discuss and compare the numerical errors caused by the approximations made in BSIM and our models.
04CC18
Horng-Chih Lin, Zer-Ming Lin and Tiao-Yuan Huang
In this study, we proposed a new methodology for probing the electrical properties of heavily doped polycrystalline silicon (poly-Si) nanowires (NWs), including active doping concentration, mobility, and interface fixed charge density. Implementation of this procedure is based on the modulation of the device operation of a gate-all-around (GAA) junctionless (J-less) transistor from the gated resistor mode to the ungated one. The extracted carrier concentration in the NW is found to be much lower than that of Hall measurements, while a negative fixed charge density is identified with the procedure. Dopant segregation at the oxide interface is postulated to be closely related to these observations.
04CC19
Ralf Granzner, Frank Schwierz, Sonja Engert and Hannes Töpfer
Off-current and threshold voltage fluctuations in trigate (TG), and single-gate (SG) silicon-on-insulator (SOI) MOSFETs with a gate length of 10 nm are studied by means of three-dimensional (3D) device simulations. Special emphasis is paid to the role of the channel design. We demonstrate that both geometry fluctuations and the presence of single charged impurities in the active device regions can easily alter the off-currents of SG and TG MOSFET designs that nominally meet the Ion/Ioff requirements by more than one order of magnitude. It will be shown that regarding the robustness against geometry fluctuations, neither the SG MOSFET nor one of the possible TG MOSFET designs can be preferred in general. The SG concept, however, turns out to be exceptionally robust against threshold voltage fluctuations caused by single charged impurities.
04CC20
Ming-Han Liao, Ci-Hua Chen, Li-Chen Chang, Chen Yang, Ming-Yuan Yu, Gan-Han Liu and Si-Cha Kao
The comprehensive investigation on the effect of dislocation edge stress for Si N-type metal–oxide–semiconductor field-effect transistors (N-MOSFETs) is presented in this work by the experimental measurement and proposed simulation model. The accurate stress measurement in Si oxide dimension (OD) region with and without dislocation edge stress treatment is extracted by atomic force microscope (AFM)–Raman technique with the nanometer level space resolution. Less compressive stress in Si OD region on the real transistor with dislocation edge stress treatment is observed successfully and has its corresponding higher electron carrier mobility, agreed with the strained Si theory. Main reasons for the less compressive stress in the device with dislocation edge stress treatment are the more stress relaxation of the shallow trench insulator (STI) intrinsic compressive stress in modern CMOS process and one layer Si atom missing near the source and drain region along the dislocation line. The measured stress from AFM–Raman spectra experimentally, the simulated stress from proposed finite element method, and its corresponding electrical characteristics agrees well with each other in this work. After the comprehensive understanding and calibrated model for the dislocation edge stress, the relationship between channel stress and dislocation edge shapes, including the angle and length of dislocation lines, is simulated and investigated clearly. It can be found that longer dislocation line and smaller dislocation angle can relax the intrinsic STI compressive stress more and should have the better electron carrier mobility and device performance for N-MOSFETs.
04CC21
Do-Young Choi, Chang-Woo Sohn, Hyun Chul Sagong, Eui-Young Jung, Chang Yong Kang, Jeong-Soo Lee and Yoon-Ha Jeong
This paper describes the degradation and recovery characteristics of SiGe pMOSFETs with a high-k/metal gate stack under negative-bias temperature instability (NBTI) stress. The threshold voltage instability (ΔVth) of SiGe pMOSFETs shows an increased percentage of recovery (R) as well as lower degradation than those of control Si pMOSFETs. It is found that the recovery characteristics of SiGe and Si pMOSFETs have similar dependencies on various stress conditions, and the increased R of SiGe pMOSFETs is mainly attributed to their lower degradation characteristic. Under real operating conditions, most of the ΔVth caused by hole trapping would be rapidly recovered through a fast recovery process, and newly-generated interface traps during the stress would determine the degradation level of Vth. The SiGe pMOSFETs show lower stress-induced interface traps; thus, they would display more reliable NBTI characteristics than Si pMOSFETs under real operating conditions.
04CC22
Hsu Feng Chiu, San Lein Wu, Yee Shyi Chang, Shoou Jinn Chang, Po Chin Huang, Jone Fang Chen, Shih Chang Tsai, Chien Ming Lai, Chia Wei Hsu and Osbert Cheng
In this research, trap properties in n-channel metal–oxide–semiconductor field-effect transistors (MOSFETs) with different annealing sequences have been studied on the basis of low-frequency (1/f) noise and random telegraph noise (RTN) analyses. The 1/f noise results indicate that the source of the drain current fluctuation is electron trapping. The higher trap density in the devices annealed before the TaN layer causes serious noise and lower trap energy in RTN results. The substitution mechanism explains that the increment of defects is due to the additional nitrogen atoms in HfO2. On the contrary, fewer defects in the devices annealed after the TaN layer are due to the effect of passivation in the TiN layer. The defect in HfO2 is the source of trapping/detrapping; thus, fewer defects cause the decrement of the fluctuation and the increment of the drain current. We believe that this process has a potential to remove defects in advanced MOSFETs.
04CC23
Hideo Sakai, Shin-ichi O'uchi, Kazuhiko Endo, Takashi Matsukawa, Yongxun Liu, Yuki Ishikawa, Junichi Tsukada, Tadashi Nakagawa, Toshihiro Sekigawa, Hanpei Koike et al
In this work, we measured 1/f noise of independent-double-gate- (IDG-) fin-type FET (FinFET) which has two independent gates. Flicker noise of common-double-gate- (CDG-) mode which both gates are applied with the same voltage and IDG-mode that has one gate voltage grounded and the other gate voltage applied with arbitrary voltage, and both result were compared with the same drain current (Id). First, we measured relationship between characteristic of the normalized 1/f noise by Id (SId/Id2) and characteristic of Id. Both the SId/Id2 of IDG- and CDG-modes show nearly equal values and tendency. Next, this work also shows the relationship between 1/f noise and vertical electric field (E⊥) of surface of gate oxide film. As a result we could not definitely see a large margin of 1/f noise between CDG- and IDG-modes from E⊥. This work also discovered that 1/f noise was greatly influenced by Id density.
04CC24
Bo-Chin Wang, San-Lein Wu, Yu-Ying Lu, Chien-Wei Huang, Chung-Yi Wu, Yu-Min Lin, Kun-Hsien Lee, Osbert Cheng, Po-Chin Huang and Shoou-Jinn Chang
In this study, the effect of uniaxial tensile on the SiO2/Si interface of the 28 nm n-type metal–oxide–semiconductor field-effect transistors (nMOSFETs) has been investigated. nMOSFETs were fabricated with different thicknesses of the stress-memorization technique (SMT) films to further increase channel stress because the SMT films can provide a higher uniaxial tensile to the channel. Trap behaviors such as activation energy and depth were characterized on the basis of drain current random telegraph noise (RTN). By RTN analyses, we found that the trap energy level is closer to the channel conduction band as the tensile strain in the channel increases higher, resulting in the trap being located close to the SiO2/Si interface.
04CC25
Yukinori Morita, Takahiro Mori, Shinji Migita, Wataru Mizubayashi, Akihito Tanabe, Koichi Fukuda, Meishoku Masahara and Hiroyuki Ota
We fabricate p- and n-channel Si tunnel field-effect transistors (TFETs) with an epitaxially grown tunnel junction. In a novel source/drain-first and tunnel-junction-last fabrication process, a thin epitaxial undoped Si channel (epichannel) is deposited on a preferentially fabricated p- or n-type source area. The epichannel sandwiched by a gate insulator and a highly doped source well acts as a parallel-plate tunnel capacitor, which effectively multiplies drain current with an enlarged tunnel area. On the basis of its simple structure and easy fabrication, symmetric n- and p-transistor and complementary metal oxide semiconductor inverter operations were successfully demonstrated.
04CC26
Sung-Ho Jeon, Noriyuki Taoka, Hiroaki Matsumoto, Kiyotaka Nakano, Susumu Koyama, Hiroshi Kakibayasi, Koji Araki, Moriya Miyashita, Koji Izunome, Mitsuru Takenaka et al
The effects of high-temperature Ar/H2 annealing on (110) Si, which is known to provide flat (110) Si surfaces, have been studied from the viewpoint of metal–oxide–semiconductor (MOS) interface roughness and inversion-layer electron mobility limited by surface roughness scattering in (110) Si n-channel metal–oxide–semiconductor field-effect transistors (n-MOSFETs). It has been confirmed by quantitative transmission electron microscope (TEM) analysis that the reduction in the surface roughness on (110) Si is still maintained after gate oxidation with gate oxide thickness (Tox) of 6.9 nm. The mobility measurement of (110) Si n-MOSFETs fabricated using Si wafers with high-temperature Ar/H2 annealing has revealed that the high-temperature annealing increases the electron mobility of (110) Si MOSFETs at 10 K by 14 and 5.7% for Tox values of 6.9 and 8.9 nm, respectively, and increases the electron mobility at 300 K by 2.5 and 0.72% for Tox values of 6.9 and 8.9 nm, respectively. The Tox dependence of the enhancement factor might be attributable to the increase in MOS interface roughness with increasing Tox. It has also been observed that the mobility enhancement factor is slightly dependent on the channel direction. The mobility increase has been observed to be greater along <111> than along <112>.
04CC27
Min-Hung Lee, Jhe-Cyun Lin, Cheng-Ying Kao and Chih-Wei Chen
P-type tunneling-based high-driving-current green field-effect transistors (p-gFETs) with dopant segregation (DS) on bulk Si were successfully fabricated and developed. gFETs with the vertical band-to-band tunneling (BTBT) mechanism have a valid benefit for ∼25× ON current enhancement compared with tunneling field-effect transistors (TFETs) without sacrificing leakage current and subthreshold swing for CMOS scaling in future-generation transistors. Ni DS enhanced the amount of n+ dopant in the source/drain region and produced a steep junction profile, which improved the BTBT mechanism. The promising gFET with silicon-on-insulator-free (SOI-free) gFET can be compatible with current processes and solve the issues of cost and thermal dissipation.
04CC28
Yan Wu, Chunmeng Dou, Feng Wei, Kuniyuki Kakushima, Kenji Ohmori, Parhat Ahmet, Takanobu Watanabe, Kazuo Tsutsui, Akira Nishiyama, Nobuyuki Sugii et al
The influence of structural parameters, including the Schottky barrier height for electron (φBn) and channel doping (Na), on the electrical characteristics of a scaled Schottky barrier tunneling FET (SBTFET) have been clarified by numerical device simulation. The thermionic emission current (ITH) as well as the tunneling current (ITN) have been considered as the main electron injections at the source edge. Simulation results have revealed that the main conduction is ITN in the region near and above the threshold voltage (Vth). As tunneling probability is determined by φBn and the width of the triangular potential barrier at the source edge, a lower φBn with higher Na results in a better subthreshold swing (SS) with high on-state drive current (ION) at a gate length (Lg) of 50 nm. With Lg scaling down to 10 nm, however, a lower φBn has shown an increased off-state leakage current (IOFF) due to the short-channel effect (SCE), while a larger φBn can suppress the IOFF at the cost of ION. Therefore, considering SS with ION and IOFF ratio, it can be concluded that an optimum φBn exists for short-channel devices. The SBTFET showed good subthreshold performance and higher ION/IOFF than the conventional silicon-on-insulator (SOI) MOSFET in 10 nm region with the Schottky barrier height optimization.
04CC29
Xingye Zhou, Takuya Inoue, Masashi Kitamura, Kai Matsuura, Masataka Miyake, Takahiro Iizuka, Takuya Umeda, Hideyuki Kikuchihara, Hans Juergen Mattausch, Jin He et al
It is demonstrated that the self-heating effect easily causes elevated thermal equilibrium condition within the active device for thin substrate MOSFETs. This leads to a non-linearity of the thermal resistance, which originally is a material specific constant. A compact model for describing the observed effective nonlinear thermal resistance has been developed which captures the device geometry effects as well as the bias condition dependences.
Advanced memory technology
04CD01
Fu-Hai Li, Yung-Yueh Chiu, Yen-Hui Lee, Ru-Wei Chang, Bo-Jun Yang, Wein-Town Sun, Eric Lee, Chao-Wei Kuo and Riichiro Shirota
In this study, we precisely investigate the charge distribution in SiN layer by dynamic programming of channel hot hole induced hot electron injection (CHHIHE) in p-channel silicon–oxide–nitride–oxide–silicon (SONOS) memory device. In the dynamic programming scheme, gate voltage is increased as a staircase with fixed step amplitude, which can prohibits the injection of holes in SiN layer. Three-dimensional device simulation is calibrated and is compared with the measured programming characteristics. It is found, for the first time, that the hot electron injection point quickly traverses from drain to source side synchronizing to the expansion of charged area in SiN layer. As a result, the injected charges quickly spread over on the almost whole channel area uniformly during a short programming period, which will afford large tolerance against lateral trapped charge diffusion by baking.
04CD02
Giorgio Palma, Elisa Vianello, Gabriel Molas, Carlo Cagli, Florian Longnos, Jérémy Guy, Marina Reyboz, Catherine Carabasse, Mathieu Bernard, Faiz Dahmani et al
In this paper, the effect of the active layer thickness and temperature on the switching kinetics of GeS2-based conductive bridge memories is addressed through electrical characterization. Results are explained in terms of a thermally and field driven ion hopping model for reversible resistance switching. The combined analysis reveals that at high temperature the set voltage and the set resistance decrease. Furthermore, the study suggests that applying the same reset condition, for GeS2 thicknesses lower than 50 nm, the conductive filament is almost dissolved, while for thicker layers a portion of the filament still remains.
04CD03
Xin Tong, Wenjuan Wu, Zhe Liu, Xuan Anh Tran, Hong Yu Yu and Yee-Chia Yeo
We report on a novel TaOx-based nonpolar resistive random access memory (RRAM) cell design with a Cr/TaOx/Al (top-to-bottom) structure. Extensive studies of the switching mechanism of the nonpolar RRAM were performed. The thermal coefficient of resistance of the RRAM in the low-resistance state is observed to adopt different polarities depending on how the preceding set operation was performed. On the basis of this observation, the coexistence of metallic ions and oxygen vacancies in the dominant filament is deduced, and a hybrid filament hypothesis is proposed for the first time to explain the observations. A switching model is provided to explain the microscopic changes in the nonpolar TaOx-based RRAM.
04CD04
Peng Huang, Yexin Deng, Bin Gao, Bing Chen, Feifei Zhang, Di Yu, Lingfeng Liu, Gang Du, Jinfeng Kang and Xiaoyan Liu
Large switching current is a great challenge for scaling down of the oxide-based resistive random access memory devices to realize high density and low power memory array. In this paper, large operation current caused by the current overshoot effect during forming process is investigated using a stochastic simulator based on the percolation theory. The electrical characteristic of forming process is simulated and compared with the experimental data. Our simulation demonstrates that the current overshoot effect results in a stronger conductive filament during forming process, which will cause a larger operation current in subsequent switching cycle. Furthermore, our simulation results reveal that low sweeping rate, high ambient temperature, high doping concentration and high pre-exist oxygen vacancies (VO) concentration are beneficial to the control of conductive filament evolution and the suppression of the current overshoot effect, which is critical for low reset current and low operation power resistive-switching random access memory (RRAM).
04CD05
Beomyong Kim, Wangee Kim, Hyojune Kim, Kyooho Jung, Wooyoung Park, Bomin Seo, Moonsig Joo, Keejeung Lee, Kwon Hong and Sungki Park
The effects of TiN top electrode composition (TiN vs Ti-rich TiN) on the resistive switching characteristics of selector-less TiN/TiOx/Ta2O5/TiN resistive random access memory (ReRAM) are investigated. Ti-rich TiN enables TiOx to have a higher concentration of oxygen vacancy and reduce barrier height between top electrode and TiOx. This leads to higher on/off current ratio and lower operation voltage without degradation of non-linearity which is the important factor for selector-less type ReRAM, compared to the stoichiometric TiN resistor stack. Consequently, it is verified that the switching mechanism is hybrid combination of filament formation and redox reaction in switching operation. This work is applicable to both high density and cost-effective ReRAM.
04CD06
Xavier Saura, Enrique Miranda, David Jiménez, Shibing Long, Ming Liu, Joan Marc Rafí, Francesca Campabadal and Jordi Suñé
Volatile threshold switching and non-volatile memory switching modes of resistive switching are reported in Al/HfO2/Si(p) metal–oxide–semiconductor structures with different values of current compliance limit during electroforming. When the current is limited to below 100 µA, a reproducible threshold switching loop is reported under injection from the p-type silicon substrate. The conduction in the low resistance state is linear above a voltage threshold called holding voltage and the conductance is a non-integer multiple of the quantum of conductance. Depending on the size of the conducting filament created during the electroforming process, one or several quasi-one dimensional quantum subbands are found to contribute to the current. Abrupt transitions between different discrete conductance values are reported during increasing and decreasing voltage sweeps. These results provide strong experimental evidence suggesting that the conduction filament behaves as a quantum wire (QW). No structural instability of the filament has to be invoked to explain either the highly structured conduction properties or the set and reset switching transitions. It is claimed that the whole phenomenology can be understood by electron injection from the valence band into a narrow conducting path which behaves as a QW.
04CD07
Jer-Chyi Wang, Yu-Ren Ye, Jhih-Sian Syu, Pin-Ru Wu, Chih-I Wu, Po-Sheng Wang and Jung Hung Chang
The effects of remote NH3 plasma treatment on a Pt/GdxOy/W resistive random access memory (RRAM) metal–insulator–metal (MIM) structure were investigated. We found that a decrease in the electron barrier height caused by nitrogen incorporation at the Pt–GdxOy interface can help reduce the operational set and reset voltages. Nitrogen atoms from the NH3 plasma prevent oxygen atoms in the film from diffusing through Pt grain boundaries into the atmosphere, resulting in superior retention properties (>104 s). The stability of the endurance behavior of GdxOy RRAMs was significantly improved owing to the passivation of defects in GdxOy films by nitrogen and hydrogen atoms from the remote NH3 plasma, markedly reducing plasma damage.
04CD08
Takuya Imamoto and Tetsuo Endoh
In this paper, the novel field effect diode (FED) type vertical capacitorless one transistor dynamic random access memory (1T-DRAM) cell with negative hold bit line (BL) voltage (VBL) scheme is proposed. In comparison with the conventional planar type, the proposed vertical type with negative hold VBL scheme shows excellent static and disturb retention time. The proposed vertical type memory cell with negative hold VBL scheme achieves 1,000 times longer static retention time and 104 times longer BL disturb retention time at 85 °C than that of the conventional planar type. Furthermore, the proposed vertical type memory cell has a small cell size of 4F2 due to its stacked vertical structure. The proposed FED type vertical capacitorless 1T-DRAM cell with negative hold VBL scheme is shown to be an excellent candidate for stand-alone and embedded memory applications and extends scaling limitations.
04CD09
Akihiro Sumi, Takahiro Oikawa, Hitoshi Morioka, Shoji Okamoto, Shintaro Yokoyama, Takayuki Watanabe, Yoshitaka Ehara and Hiroshi Funakubo
Squareness in polarization–electric field hysteresis loops of (100)-oriented epitaxial and fiber-textured rhombohedral Pb(Zr,Ti)O3 films prepared on (100) SrTiO3 and (100) Si substrates, respectively, was investigated as a function of temperature. The ratio of remanent polarization to saturation polarization (Pr/Psat) decreased with increasing temperature for all films. It depends on the kind of substrates and the remained strain in the in-plane orientation. These data suggest that the existing strain in the films possibly affects the temperature dependence of the Pr/Psat ratio.
04CD10
Daniele Ielmini, Simone Balatti and Stefano Larentis
Bipolar resistive switching memory (RRAM) relies on ion migration effects taking place at a conductive filament (CF). Understanding the evolution of the CF during set and reset transitions is essential for predicting RRAM scalability and for developing new methods for storage and computation. This work describes the evolution of the CF during bipolar resistive switching through numerical simulations of ion drift/diffusion. The defect distribution profile for increasing current after set transition and for increasing voltage during set transition are shown. Finally, the asymmetric shape of the CF is evidenced through polarity-dependent experiments and explained through numerical simulations.
04CD11
Moon Young Yang, Katsumasa Kamiya, Blanka Magyari-Köpe, Hiroyoshi Momida, Takahisa Ohno, Masaaki Niwa, Yoshio Nishi and Kenji Shiraishi
We theoretically clarified the atomistic role of the Al2O3 oxygen vacancy (VO) barrier layer in advanced ReRAM stacks. We found that VO filament formation in Al2O3 can be controlled by applying voltage when the Al2O3 layer is in contact with VO source layer such as Hf, although VO formation in Al2O3 is difficult in usual situation. Moreover, we proposed a physical guiding principle toward designing high quality ReRAM stacks with Al2O3 VO barrier layers.
04CD12
Tomoko Ogura Iwasaki, Sheyang Ning and Ken Takeuchi
The potential of resistive random access memory (ReRAM) to provide high speed operation is held back by the need to verify during set/reset, and sensitivity to read disturb. 50 nm HfO2 cells are measured for disturb in forward and reverse directions, and at 25 and 85 °C. Two circuit proposals provide speed and reliability improvement. First, bipolar verify reduces write time. If the verify direction matches the set/reset direction, read voltage can be increased, which reduces signal development time, and eliminates the need to switch the highly capacitive source line voltage. Secondly, reverse read with dynamic write-back provides fast, disturb-free read. A margin-check is performed in parallel to normal reverse-read. Disturb of the low resistance state is monitored, and then, if needed, set write-back occurs. Based on disturb data, write-back occurs infrequently, after ∼5×109 reads. By these two proposals, write time can be reduced by 3× and 5× faster read with disturb immunity can be achieved.
04CD13
Yahua Peng, Fei Liu, Xiaoyan Liu, Gang Du and Jinfeng Kang
In this work, we evaluate the program/erase/retention performance of a novel TaN/Al2O3/TiO2/HfO2/SiO2/Si (TATHOS) charge trapping memory (CTM) device with the stacked HfO2/SiO2 tunneling layer and TiO2 charge trapping layer by our developed simulator, which has included the critical mechanisms in CTM and has been verified with the experiment data. With various gate dielectric layer's thicknesses and materials, bias voltages and temperatures, the novel structure device's performance are studied and compared to some conventional devices. It can been seen that with appropriate design for the stack tunneling layer and TiO2 choice for the charge trapping layer, significantly improved program/erase speed and retention characteristics could be achieved. It can be a useful tool to optimize the performance of CTM with the gate layer materials' choice and design.
04CD14
Hyung-jun Yang, Gae-hun Lee, Kyeong-rok Kim and Yun-heub Song
A bit-cost scalable (BiCS) NAND flash memory with a bulk erasing method is investigated in view of cell characteristics and uniformity. The proposed cell array has an additional electrode layer for a bulk erase operation in the middle of a vertical channel string cell. Here, under a bias condition of 20 V, a programming threshold voltage of 4.2 V at 1 ms and an erasing threshold voltage of Vth = -1.5 V at 10 ms are confirmed, which is acceptable for flash memories. Furthermore, the shielding transistor close to an erase electrode is also investigated, which gives better erase characteristics for the cells adjacent to the erase electrode. From this result, we expect that a bulk erasable-BiCS technology with a shielding transistor can be a candidate three-dimensional (3D) NAND flash memory.
Advanced circuits and systems
04CE01
Shin Sakai, Yoshiaki Tashiro, Rihito Kuroda and Shigetoshi Sugawa
In this paper, a global-shutter complementary metal oxide semiconductor (CMOS) image sensor using lateral overflow integration capacitor (LOFIC) in each pixel without trade-offs between full-well capacity (FWC) and dark current and between FWC and pixel size has been demonstrated. Because the FWC is determined only by LOFIC, a photodiode (PD) and storage diffusion capacitor (SD) are designed focusing on achieving low dark current performance especially. A 2.8 µm pixel pitch Bayer-RGB color CMOS image sensor with the pinned diffusion capacitor for the storage node was fabricated and achieved both 83.3 e-/s at the PD and 58.3 e-/s at the SD dark current at 60 °C and about 55 ke- full well capacity. A high resolution performance, a high FWC performance and a low dark current performance were simultaneously achieved in this image sensor.
04CE02
Atsutake Kosuge, Tsutomu Takeya, Mitsuru Shioya, Masao Taguchi and Tadahiro Kuroda
A non-contact inter-module link technique which consists of transmission line couplers (TLCs) and an equalizing receiver is proposed. The non-contact interface allows eliminating metal terminals and eases electro-static discharge (ESD) protection constraints, leading to higher channel bandwidth. Signals pass through two TLCs via a transmission line so that they are differentiated twice (d2v/dt2) and turn into double-peak pulses. To retrieve original waveforms, we developed a low-frequency compensation continuous time linear equalizer (LFC-CTLE) to emphasize the low frequency part converting the double-peak pulses to the first order differentiated shapes, resulting in improving the data rate. To verify this technique, we designed and fabricated a test chip in 0.18 µm CMOS technology and we achieved 3 Gbps data rate at the bit error rate of (BER) less than 10-11 with a 10-in. long FR4 micro strip line and two 11 mm length TLCs.
04CE03
Satoru Tanoi and Tetsuo Endoh
A low-voltage differential signaling (LVDS) driver with a new current reuse topology is proposed for low power-supply voltage (VDD) operation. The proposed driver has a new current mirror with shared MOSFET and is designed using vertical MOSFETs. The new current mirror reduces the output degradation to less than half of the conventional. And the design with vertical MOSFETs reduces the voltage drop of the eight-stage cascode circuit to 77.6% of that with planar ones. Our current reuse driver achieves 3-mW/Gbps with 2.5-Gbps and 1.8-V VDD operation in the simulation using 0.18-µm gate length MOSFET parameters. The achieved reduction of the power normalized by the output power at 1.8-V VDD is larger than 30% of that for the conventional drivers.
04CE04
Tsung-Ling Li, Shin Sakai, Shun Kawada, Yasuyuki Goda, Shunichi Wakashima, Rihito Kuroda and Shigetoshi Sugawa
In this paper, a column-parallel hybrid analog-to-digital converter (ADC) architecture taking the advantages of both successive-approximation-register (SAR) and single-slope (SS) architectures has been developed for CMOS image sensors. The proposed architecture achieves high conversion speed and low power consumption without requiring a high clock frequency and a large number of capacitors. Moreover, an error correction methodology has been presented to calibrate capacitance mismatches in a SAR capacitor array for linearity improvement. An 11-bit hybrid prototype ADC has been implemented in a 0.18-µm 1-poly 5-metal standard CMOS process. The conversion time is 1.225 µs with a maximum operation clock frequency of 40 MHz and it consumes 48 µW. With the proposed error correction, the measured differential nonlinearity (DNL) and integral nonlinearity (INL) are +0.40/-0.44 least significant bit (LSB) and +1.21/-1.12 LSB, respectively.
04CE05
Takashi Matsumoto, Kazutoshi Kobayashi and Hidetoshi Onodera
The statistical nature of random telegraph noise (RTN) induced delay fluctuation is described by measuring 1,655 ROs fabricated in a commercial 40 nm CMOS technology. A small number of samples have a large RTN-induced delay fluctuation. We investigated the impact of the body-biasing technique on RTN-induced circuit delay fluctuation for various substrate bias conditions. The impact of RTN-induced delay fluctuation tends to be reduced by the forward body-biasing technique, but a few ROs still have a large fluctuation.
04CE06
Yu Nishitani, Yukihiro Kaneko, Michihito Ueda, Eiji Fujii and Ayumu Tsujimura
A brain-like learning function was implemented in an electronic synapse device using a ferroelectric-gate field effect transistor (FeFET). The FeFET was a bottom-gate type FET with a ZnO channel and a ferroelectric Pb(Zr,Ti)O3 (PZT) gate insulator. The synaptic weight, which is represented by the channel conductance of the FeFET, is updated by applying a gate voltage through a change in the ferroelectric polarization in the PZT. A learning function based on the symmetric spike-timing dependent synaptic plasticity was implemented in the synapse device using the multilevel weight update by applying a pulse gate voltage. The dynamic weighting and learning behavior in the synapse device was observed as a change in the membrane potential in a spiking neuron circuit.
04CE07
Akihiro Toya, Kenta Sogo, Nobuo Sasaki and Takamaro Kikkawa
For application to an impulse-radio ultra-wideband (IR-UWB) portable breast cancer detection system, a 102.4 GS/s sampling circuit is developed. The high sampling rate is realized by an equivalent-time sampling technique and a low-power multi-clock generation circuit using a phase interpolator. The phase interpolator achieved a minimum phase resolution 9.8 ps. Using the sampling circuit, a tumor phantom buried by a breast phantom was detected.
04CE08
Hyoungjun Na and Tetsuo Endoh
In this paper, a dynamic random access memory (DRAM) core circuit realizing sub-1 V core voltage operation without using the overdriven sense amplifier technique is proposed by using the multi-pillar vertical MOSFET, and its performance is described with the HSPICE simulation. The proposed DRAM core circuit realizes the same sensing time at 0.6 and 0.75 V lower core supply voltage without and with the overdriven sense amplifier technique, respectively, comparing to the conventional DRAM core circuit by the planar MOSFET with the overdriven sense amplifier technique. Moreover, when VCORE is 1.25 V and VDD is 1.5 V, the overdriven proposed sense amplifier achieves 79% (2.7 ns) faster sensing time than the overdriven conventional sense amplifier. Furthermore, the proposed circuit achieves a faster wordline transition and precharge time than the conventional DRAM core circuit by approximately 17% (1.1 ns) and 55% (0.2 ns), respectively. This proposed DRAM core circuit is a promising circuit technique for low voltage and high speed DRAM core circuit operation.
04CE09
Ming-Hsien Tsai, Sing-Kai Huang and Shawn S. H. Hsu
The RF junction varactors are employed as electro-static discharge (ESD) protection devices and co-designed with 60 GHz low-noise amplifier (LNA) fabricated in a 65-nm CMOS technology. The junction varactor acts as an ESD diode to bypass ESD current during ESD zapping, and also utilized as a capacitor to be a part of input matching network of the LNA in normal RF operation. By transmission line pulse (TLP) measurement, the ESD protection capabilities of RF junction varactors are characterized with different device parameters. The experimental results demonstrate excellent second breakdown currents (It2) and high ratios of the ESD levels to parasitic capacitances (VESD/CESD). With ESD/matching co-design methodology, the ESD-protected LNA demonstrates a second breakdown current It2 of 1.4 A, corresponding to a 2-kV human-body-model (HBM) ESD protection level with a noise figure (NF) of 6.6 dB and a peak gain of 16.5 dB at 60 GHz under a power consumption of only 28 mW.
04CE10
Tetsuya Ariyoshi, Akiyoshi Baba and Yutaka Arima
We have proposed a simple method for color imaging in which the photosensor is illuminated from the side. In this method, color imaging can be produced using single pixels and without generating false colors and moiré patterns. A 5.0 ×5.0 mm2 test chip was fabricated using a 0.35 µm complementary metal oxide semiconductor (CMOS) 1-poly 4-metal process. Because the side illumination method is used, the side of the test chip was etched using a high-speed deep reactive ion etching (D-RIE) process. Light illumination experiments confirmed that four colors – blue, green, red, and near-infrared – could be separated using this method. We also estimated the color separation properties of a similar sensor based on a 0.18 µm CMOS process.
04CE11
Zuoxun Hou, Yitao Ma, Hongbo Zhu, Nanning Zheng and Tadashi Shibata
A very large-scale integration (VLSI) recognition system equipped with an on-chip learning capability has been developed for real-time processing applications. This system can work in two functional modes of operation: adaptive K-means learning mode and recognition mode. In the adaptive K-means learning mode, the variance ratio criterion (VRC) has been employed to evaluate the quality of K-means classification results, and the evaluation algorithm has been implemented on the chip. As a result, it has become possible for the system to autonomously determine the optimum number of clusters (K). In the recognition mode, the nearest-neighbor search algorithm is very efficiently carried out by the fully parallel architecture employed in the chip. In both modes of operation, many hardware resources are shared and the functionality is flexibly altered by the system controller designed as a finite-state machine (FSM). The chip is implemented on Altera Cyclone II FPGA with 46K logic cells. Its operating clock is 25 MHz and the processing times for adaptive learning and recognition with 256 64-dimension feature vectors are about 0.42 ms and 4 µs, respectively. Both adaptive K-means learning and recognition functions have been verified by experiments using the image data from the COIL-100 (Columbia University Object Image Library) database.
04CE12
Boram Kim and Kazuo Nakazato
A dual data pulse width modulator is proposed and demonstrated for radio frequency identification (RFID) biosensor signal modulation. Simultaneous wireless measurement of two sensors can be carried out using this circuit, in which two analog signals are modulated and transmitted in a single clock cycle. The measured modulation sensitivity of the two input channels is 84.69 and 85.16 µs/V and the dynamic range is 55.6 and 63.5 dB, respectively. Here, redox potential and temperature are measured wirelessly using the proposed circuit. Temperature change measurement shows a sensitivity of 9.501 µs/°C in the range of 25–40 °C. The measured redox potential shows fairly good linearity for a concentration ratio of hexacyanoferrate (III) to (II) ranging from 10-2 to 102 and the slope is 58.0 mV/decade, almost the same as the theoretical value. The chip area and power consumption are 0.36 mm2 and 650 µW, respectively, using 1.2-µm, 2-metal, 2-poly CMOS technology.
04CE13
Zheye Wang and Tadashi Shibata
A difference-of-Gaussian (DoG) analog CMOS image sensor architecture in which the kernel size and shape are made arbitrarily programmable has been developed based on the MOS subthreshold characteristics. The variability of MOS transistor threshold voltage causes a serious problem in the circuits operating in the subthreshold regime because the current varies exponentially depending on the threshold voltage. The problem has been alleviated by introducing a cancellation scheme employing a switched floating-gate MOS (neuMOS) circuitry. A proof-of-concept chip was designed in a 0.18-µm CMOS technology. The operation of the designed circuits was investigated by SPICE (simulation program with integrated circuit emphasis) simulation and their basic functions were demonstrated. A part of the core function, i.e., the generation of the Gaussian function profile, was confirmed by the measurement of a fabricated test circuit.
04CE14
Takuya Sawada, Hidehiro Takata, Koji Nii and Makoto Nagata
Static random access memory (SRAM) cores exhibit susceptibility against power supply voltage variation. False operation is investigated among SRAM cells under sinusoidal voltage variation on power lines introduced by direct RF power injection. A standard SRAM core of 16 kbyte in a 90 nm 1.5 V technology is diagnosed with built-in self test and on-die noise monitor techniques. The sensitivity of bit error rate is shown to be high against the frequency of injected voltage variation, while it is not greatly influenced by the difference in frequency and phase against SRAM clocking. It is also observed that the distribution of false bits is substantially random in a cell array.
04CE15
Sho Ikeda, Sang-yeop Lee, Tatsuya Kamimura, Hiroyuki Ito, Noboru Ishihara and Kazuya Masu
In this paper, we present a fractionally injection-locked frequency multiplication technique that can solve the tradeoff between the selectable frequency step and phase noise of injection-locked frequency multipliers (ILFMs). For a given output frequency step, the phase noise of the proposed ILFM is lower than that of conventional ILFMs because higher-frequency signals can be injected. The proposed ILFM was fabricated using a 180 nm Si complementary metal oxide semiconductor (CMOS) process. 1/2-, 1/3-, 1/4-, and 1/6-integral frequency multiplications were realized, which means that the output frequency resolution is 6 times as high as that of conventional ILFM. When the reference frequency was 100 MHz, the measured phase noise at 725 (= 100×29/4) MHz was -120 dBc/Hz at a 1 MHz offset, and that at 767 (= 100×23/3) MHz was -119 dBc/Hz at 1 MHz offset.
Compound semiconductor electron devices and related technologies
04CF01
Taihei Ito, Azusa Kadoda, Koji Nakayama, Yuichiro Yasui, Masayuki Mori, Koichi Maezawa, Eiji Miyazaki and Takashi Mizutani
Al2O3/InSb/Si quantum well MOSFETs were fabricated with a thin InSb channel layer grown directly on Si(111) substrates. The InSb thickness ranged from 6 to 25 nm. These thicknesses are close to the critical thickness of InSb on Si, when the InSb layer is grown using a special technique called surface reconstruction controlled epitaxy, which reduces the lattice mismatch from 19.3 to 3.3% by rotating the in-plane InSb axis by 30° with respect to the Si(111) substrate. Good FET characteristics were observed for 10 nm InSb channel devices. The dependence of the device properties on InSb channel thickness was investigated. The enhancement of effective mobility for thin InSb channel devices was demonstrated, which indicates the crystal quality improvement when approaching the critical thickness.
04CF02
Masanobu Hiroki, Noriyuki Watanabe, Narihiko Maeda, Haruki Yokoyama, Kazuhide Kumakura and Hideki Yamamoto
We fabricated InAlN/AlGaN/GaN heterostructures using a regrowth technique in order to avoid an unintentional Ga incorporation into the InAlN barrier layer. We prepared two types of samples (S1 and S2) using different regrowth sequences: InAlN regrowth on AlGaN/GaN (S1), and InAlN/AlGaN/GaN regrowth on GaN (S2). The characteristics of the high electron mobility transistors (HEMTs) differed depending on the adopted sequence. In current–voltage characteristics, the kinks appear only for the HEMTs using S1 (HEMT-S1). The current reduction induced by gate-bias stress is as large as 20% in HEMT-S1, while it is only 5% in HEMT-S2. Results of our complementary experiments on AlGaN/GaN heterostructures prepared by various regrowth sequences suggest that the inferior device properties of HEMT-S1 can be attributed to higher trap density at the regrowth interfaces. The higher trap density is most likely a result of the AlGaN surface's being more easily oxidized than the GaN surface. Non-uniform decomposition of the AlGaN surface during the heating process prior to the regrowth may also play a role. The fairly a good device performance of HEMT-S2 indicates that InAlN can actually act as a good barrier for GaN-based HEMTs by careful optimization of the fabrication sequence even with a regrowth process.
04CF03
Masaru Sato, Shoichi Shiba, Hiroshi Matsumura, Tsuyoshi Takahashi, Yasuhiro Nakasha, Toshihide Suzuki and Naoki Hara
In this study, we developed a new type of high-frequency amplifier topology using 75-nm-gate-length InP-based high-electron-mobility transistors (InP HEMTs). To enhance the gain for a wide frequency range, a common-source common-gate hybrid amplifier topology was proposed. A transformer-based balun placed at the input of the amplifier generates differential signals, which are fed to the gate and source terminals of the transistor. The amplified signal is outputted at the drain node. The simulation results show that the hybrid topology exhibits a higher gain from 90 to 140 GHz than that of the conventional common-source or common-gate amplifier. The two-stage amplifier fabricated using the topology exhibits a small signal gain of 12 dB and a 3-dB bandwidth of 40 GHz (93–133 GHz), which is the largest bandwidth and the second highest gain reported among those of published 120-GHz-band amplifiers. In addition, the measured noise figure was 5 dB from 90 to 100 GHz.
04CF04
Kwang-Seok Jeong, Ho-Jin Yun, Yu-Mi Kim, Seung-Dong Yang, Sang-Youl Lee, Young-Su Kim, Hi-Deok Lee and Ga-Won Lee
To investigate the electrical instability mechanism under the application of gate bias stress and relaxation, the 1/f noise spectra of two different ZnO thin-film transistors (TFTs) were analyzed. In terms of gate bias dependence (SIDS/IDS), both devices followed a mobility fluctuation model based on the traps in their channel layers prior to and after stress. Device A (channel thickness: 20 nm), recovered its initial noise parameter (αapp) after relaxation, in exact agreement with the current–voltage (I–V) measurement results; this shows that in device A, the dominant phenomenon under the application of stress was temporary charge trapping at grain boundary traps. However, in device B (channel thickness: 80 nm), αapp did not recover its initial values after relaxation, and transfer parameters, such as VTH, mobility, SS, and Nt, degraded after the gate bias stress. Moreover, after the stress, device B showed a reduced gate insulator breakdown voltage. The electrical degradation seen in device B can be explained by trap creation and/or charge injection near channel/gate oxide interfaces, including those within the channel layer.
04CF05
Masashi Kashiwano, Jun Hirai, Shunsuke Ikeda, Motohiko Fujimatsu and Yasuyuki Miyamoto
We fabricated a vertical metal–insulator–semiconductor field-effect transistor (MISFET) with a heterostructure launcher and an undoped channel. Vertical MISFETs exhibit a high drain current density; however, their large output conductance is a disadvantage for the open-circuit voltage gain. In a previous study, a maximum voltage gain of 4.0 was found in a vertical MISFET with a heavily doped drain region and a 45-nm-wide channel mesa. The heavily doped drain region and a narrower channel width are effective in reducing the output conductance. In this study, we fabricated a device with the heavily doped drain region and a 23-nm-wide channel mesa structure. It was observed that the output conductance decreased from 120 to 57 mS/mm at a drain current density of 0.3 MA/cm2 with a narrower channel mesa. The maximum open-circuit voltage gain increased from 4.0 to 5.7.
04CF06
Xinke Liu, Chunlei Zhan, Kwok Wai Chan, Man Hon Samuel Owen, Wei Liu, Dong Zhi Chi, Leng Seow Tan, Kevin Jing Chen and Yee-Chia Yeo
This paper reports the fabrication and characterization of AlGaN/GaN-on-sapphire metal–oxide–semiconductor high-electron-mobility transistors (MOS-HEMTs) using a complementary metal–oxide–semiconductor (CMOS) compatible gold-free process. Devices with a gate-to-drain spacing LGD of 20 µm achieved an off-state breakdown voltage VBR of 1400 V and an on-state resistance Ron of 22 mΩ·cm2. This is the highest VBR achieved so far for gold-free AlGaN/GaN MOS-HEMTs. In addition, high on/off current ratio Ion/Ioff of ∼109 and low gate leakage current IG of ∼10-11 A/mm were also obtained.
04CF07
Kenichiro Tanaka, Masahiro Ishida, Tetsuzo Ueda and Tsuyoshi Tanaka
Kinetic studies on the current collapse of a normally-OFF AlGaN/GaN heterostructure field-effect transistor under a high voltage have been performed above room temperature. The ON-state resistance after the ON switching from the OFF state increases at high temperatures, contrary to the expectation that the emission of electrons is enhanced at elevated temperatures. This result indicates that elevating the temperature enhances not only the emission of electrons but also their capture. We experimentally observe that the enhancement of the capture process at high temperatures originates from the energy barrier for the capture of electrons, the value of which is determined to be 0.17±0.04 eV. The origin of the energy barrier for the capture process is explained by a configuration coordinate diagram.
04CF08
Takashi Katsuno, Masakazu Kanechika, Kenji Itoh, Koichi Nishikawa, Tsutomu Uesugi and Tetsu Kachi
The improvement of current collapses of p-GaN gate GaN high-electron-mobility transistors (HEMTs) caused by the effects of surface treatment and the passivation layer was investigated. The NH3 treatment and high-temperature oxide (HTO) passivation layer on the AlGaN layer are effective in improving the current collapse of a p-GaN gate GaN HEMT. The current collapse at a long time constant (τ= 4 s) could be decreased by the NH3 treatment of the AlGaN layer, because the nitrogen atoms in nitrogen vacancies in the AlGaN layer (trap level: 0.6 eV) would be incorporated, resulting in a low surface density. The current collapse at an intermediate time constant (τ= 11 ms) could also be decreased by the deposition of the HTO passivation layer on the AlGaN layer, because the low-interface-density layer (trap level: 0.4 eV) of HTO/AlGaN would be formed.
04CF09
Hiroshi Kambayashi, Takehiko Nomura, Hirokazu Ueda, Katsushige Harada, Yuichiro Morozumi, Kazuhide Hasebe, Akinobu Teramoto, Shigetoshi Sugawa and Tadahiro Ohmi
High quality SiO2/Al2O3 gate stack has been demonstrated for GaN metal–oxide–semiconductor (MOS) transistor. We confirmed that Al2O3 could realize a low interface-state density between Al2O3 and GaN, however, the breakdown field was low. By incorporating the merits of both Al2O3 and SiO2, which has a high breakdown field and a large charge-to-breakdown, SiO2/Al2O3 gate stack structure has been employed in GaN MOS devices. The structure shows a low interface state density between gate insulator and GaN, a high breakdown field, and a large charge-to-breakdown. The SiO2/Al2O3 gate stack has also been applied to AlGaN/GaN hybrid MOS heterojunction field-effect transistor (HFET). The MOS-HFET shows excellent properties with the threshold voltage of 4.2 V and the maximum field-effect mobility of 192 cm2 V-1 s-1.
04CF10
Wei Wang, Dedong Han, Jian Cai, Youfeng Geng, Liangliang Wang, Longyan Wang, Yu Tian, Xing Zhang, Yi Wang and Shengdong Zhang
We have fabricated fully transparent Al-doped ZnO thin-film transistors (AZO TFTs) on a flexible plastic substrate at room temperature. A double-stacked channel structure composed of a high-density layer and a low-density layer is also investigated to improve the device performance. As-fabricated TFTs exhibit excellent electrical performance as well as optical performance, with a saturation mobility of 31.4 cm2 V-1 s-1, a drain current on/off ratio of about 108, a subthreshold swing of 330 mV/dec, and an average transmittance in the visible wavelength range of above 70%.
04CF11
Jian Cai, Dedong Han, Youfeng Geng, Wei Wang, Liangliang Wang, Yu Tian, Lixun Qian, Xing Zhang, Shengdong Zhang and Yi Wang
High-performance aluminum-doped zinc oxide thin-film transistors (AZO TFTs) have been successfully fabricated on glass substrates. By controlling the oxygen flow ratio (OFR) during the deposition of an AZO active layer, we have demonstrated that the incorporation of oxygen in the deposition atmosphere plays an important role in improving the electronic performance of TFTs. For gate voltage VG = -2 to 5 V, the TFTs with an AZO active layer sputter deposited in an atmosphere of Ar and O2 mixture at room temperature (RT) as the channel layer exhibit much better properties than TFTs whose AZO layer was deposited in pure Ar atmosphere, such as a high saturation mobility (µsat) of 113 cm2 V-1 s-1, a positive threshold voltage Vth of 1.5 V, an improved steep subthreshold swing from 400 to 125 mV/decade, a decreased off-state current (Ioff) from 10-8 to 5×10-13 A, an increased on/off ratio from 105 to 109, and a higher transmittance of 82.5%.
04CF12
Kazuo Hayashi, Yutaro Yamaguchi, Toshiyuki Oishi, Hiroshi Otsuka, Koji Yamanaka, Masatoshi Nakayama and Yasuyuki Miyamoto
Gate leakage current mechanism in GaN high electron mobility transistors (HEMTs) has been studied using a two-dimensional thin surface barrier (TSB) model to represent two unintentional donor thin layers that exit under and outside the gate electrode due to the existence of surface defects. The donor thin layer outside the gate affects the reverse gate current at the high gate voltage above the pinch-off voltage. Higher donor concentration of thin layer outside the gate results in larger ratio of lateral to vertical components of the electric field at the gate edge. On the other hand, the electric field at the center of the gate has only the vertical electric field component. As a result, the two-dimensional effects are only important for the reverse gate current above the pinch-off voltage. We have confirmed in this paper that the simulation results provided by our model correlate very well with the experimental reverse gate current characteristics of the device for a very wide range of reverse gate voltage from 0.1 to 90 V.
Photonic devices and optoelectronic integration
04CG01
Ryuichi Ohta, Yasutomo Ota, Hiroyuki Takagi, Naoto Kumagai, Katsuaki Tanabe, Satomi Ishida, Satoshi Iwamoto and Yasuhiko Arakawa
We design and demonstrate a photonic crystal nanobeam cavity with a Q factor controllable by a micro-electro-mechanical system (MEMS). The cavity is evanescently coupled to an adjacent nanobeam waveguide, and its Q factor is controlled by electro-mechanically adjusting the gap distance between them. We experimentally demonstrate control of the Q factor from 2,250 to 2,750, by applying voltage from 0 to 11 V.
04CG02
Shintaro Kashima, Joo-Hyong Noh and Taro Arakawa
We propose a compact tunable 1×2 multimode interference (MMI) splitter based on an InGaAs/InAlAs multiple quantum well for an active trimmer for Mach–Zehnder modulator with a very high extinction ratio. The light power splitting characteristics of the splitter are theoretically investigated by a beam propagation method and a three dimensional finite-difference time-domain method. It is assumed that the core layer is composed of a multiple five-layer asymmetric coupled quantum well (FACQW) that is expected to exhibit a large electrorefractive index change owing to its unique quantum confined Stark effect. By applying reverse voltages and changing slightly the refractive indices of the localized regions surrounded by trenches for electrical isolation, the power splitting ratio can be tuned over a wide range. The length and width of the proposed MMI with four refractive index modulation regions are 192 and 6 µm, respectively. The length can be reduced to 115 µm if the number of index modulation regions is reduced to two, though the tuning range of the splitting ratio is narrowed. The simulation results show that the proposed compact MMI splitter has a low insertion loss and a low power consumption, and is promising for Mach–Zehnder modulators with a very high extinction ratio.
04CG03
Yi-Hua Hsiao, Satoshi Iwamoto and Yasuhiko Arakawa
We designed silicon photonic crystal (PhC) waveguides (WGs) for efficient silicon Raman amplifiers and lasers. We adopted narrow-width WGs to utilize two symmetric transvers-electric-like (TE-like) guided modes, which permit efficient external coupling for both the pump and Stokes waves. Modifying the size and shape of air holes surrounding the line-defect WG structures could tune the frequency difference between these two modes, at the Brillouin-zone edge, to match the Raman shift of silicon. Thus, small group velocities are also available both for pump and Stokes waves simultaneously, which results in a large enhancement of Raman gain. The enhancement factor of the Raman gain in the designed structure is more than 100 times that reported previously.
04CG04
Ken Morita, Huga Ueyama, Yukinori Yasunaga, Yoshinori Nakagawa, Takahiro Kitada and Toshiro Isu
A GaAs/AlAs multilayer cavity with a λ/2 AlAs cavity layer, which includes Er-doped InAs quantum dots (QDs) embedded in a thin strain-relaxed In0.45Ga0.55As barrier, was fabricated. Structural and optical properties were characterized by scanning electron microscopy and optical reflection measurements, respectively. We found that the cavity quality of the Er-doped QD cavity was improved by reducing the thickness of the strain-relaxed In0.45Ga0.55As barriers in the λ/2 AlAs cavity layer. Furthermore, time-resolved optical measurements were performed to study the relaxation time of the photogenerated carriers in the Er-doped QD cavity. A full width at half maximum of a 1 ps with a large reduction of slowly decaying carriers was obtained for the Er-doped QD cavity with a thin strain-relaxed In0.45Ga0.55As barrier.
04CG05
Takeru Amano, Shigenari Ukita, Laina Ma, Masahiro Aoyagi, Takeyoshi Sugaya and Kazuhiro Komori
We have calculated the thermal conductive properties and rate of temperature increase of a semiconductor laser on a polymer substrate. The temperature rises to 27 °C on the polymer interposer and the heat radiation effect is almost saturated in the case where the Au film has a thickness of 500 nm at 10 mW. Also, we have fabricated a 1.3 µm quantum dot (QD) laser with a stripe structure for the polymer interposer. We can achieve a low operating current threshold of 7 mA for the QD laser with a high mirror loss of 16 cm-1 at 1.3 µm emission because of the high quality of the QDs and the low scattering loss structure. Moreover, we have measured the heat distribution and rising temperature speed of a QD laser on a polymer substrate. These results indicate that we need to realize a high-efficiency laser source to achieve high transmission speeds in the future.
04CG06
Hidetada Komatsu, Zhao Zhang, Yoshinori Nakagawa, Ken Morita, Takahiro Kitada and Toshiro Isu
GaAs/air multilayer cavity structure is expected as a novel planar-type nonliner optical device because of the strong enhancement of optical electric fileds in the cavity. The optical Kerr signal was estimated to be two order of magnitude larger than that from GaAs/AlAs multilayer cavity with the same Q-value by numerical simulation. We fabricated a GaAs/air cavity structure with 2-period distributed Bragg reflector (DBR) layers on each side of the λ-cavity layer by wet etching of sacrificial AlGaAs layer. Measured reflection spectra showed the expected structure was successfully fabricated in some parts.
04CG07
Yuta Kitabayashi, Masaya Mochizuki, Fumitaro Ishikawa and Masahiko Kondow
We investigate inductively coupled plasma deep dry etching of Al0.8Ga0.2As for photonic crystal (PC) fabrication using the Cl2, BCl3, and CH4 mixture. On the basis of our previous work [M. Mochizuki et al.: Jpn. J. Appl. Phys. 50 (2011) 04DG15], we explore the deeper dry etching of the PC structure, investigating the impact of gas flow rate and chemical reactions. Increasing gas flow rate and process pressure resulted in deeper etching. These conditions increased the self-bias applied on the sample, which induced the sharpening of the air hole bottom and limitation of further deep etching because of the strong contribution of physical etching. The reduction of CH4 gas suppressed the sidewall passivation, counteracting the effect of the physical etching. As a result, we obtained a PC structure having air holes with a depth larger than 1.5 µm and a diameter of 120 nm.
04CG08
Hiroki Takami, Katsunori Makihara, Mitsuhisa Ikeda and Seiichi Miyazaki
We have demonstrated self-assembling formation of one-dimensionally self-aligned Si-based quantum dots (QDs) structures and applied them to an active layer of light emitting diodes (LEDs) with a semitransparent Au gate. Under forward bias conditions over threshold biases as low as ∼1.2 and ∼-2.0 V for LEDs formed on n- and p-Si(100), respectively, stable electroluminescence (EL) was observable in the near-infrared region at room temperature. The observed EL spectra could be deconvoluted into mainly two component peaks at ∼1140 and ∼1100 nm that originated from lower and upper dots, respectively, where both spectrum intensities showed a power-law relationship of the EL intensity with applied bias and input power. Notice that the slope of the component peak for the lower dots was larger than that for the upper dots, indicating that holes were stably stored in the lower dots due to a deep potential well. In fact, when an AC bias as low as ∼6.4 V (DC at 2.0 V) was applied to the LEDs with an Au gate formed on the n-Si(100), a single component peak for the lower dots was detected, indicating electron–hole recombination in the lower dots caused by alternate carrier injection from the Si(100) substrate.
04CG09
Yukinori Yasunaga, Hyuga Ueyama, Ken Morita, Takahiro Kitada and Toshiro Isu
Strong ultrafast four-wave mixing signals at ∼1.5 µm were demonstrated in a GaAs/AlAs multilayer cavity containing self-assembled InAs quantum dots (QDs) embedded in strain-relaxed In0.35Ga0.65As barriers. Time-resolved optical measurements using 100 fs pulses with 100 kHz repetition rate were carried out in the various excitation powers at room temperature. Strongly enhanced four-wave-mixing signals were observed for a cavity with two InAs QDs layers inserted in a half-wavelength (λ/2) cavity layer compared with that of a GaAs λ/2 cavity that had no QDs, in the whole range of excitation power (0.3–2 mW). For a low excitation power below 0.6 mW, the four-wave-mixing signals were about two orders of magnitude larger than that of the GaAs λ/2 cavity owing to the large nonlinearity of the InAs QDs.
04CG10
Junichi Fujikata, Makoto Miura, Masataka Noguchi, Daisuke Okamoto, Tsuyoshi Horikawa and Yasuhiko Arakawa
We studied Si waveguide-integrated metal–semiconductor–metal (MSM) and p–i–n-type Ge photodiodes (Ge-PDs), using a Si-capping layer. As for an MSM Ge-PD, the Schottky barrier height was increased up to 0.44 V by applying a 8–20 nm Si-capping layer, and a very low dark current density of approximately 0.4 nA/µm2 was achieved with a high responsivity of 0.8 A/W. In addition, a small electrode spacing of 1 µm realized high-speed photodetection of 20 Gbps. As for a p–i–n-type Ge-PD, by applying a 10–20 nm Si capping layer, the contact resistance between a metal electrode of Ti/TiN/Al and n+-Si capping layer was successfully reduced to 1×10-5 Ω·cm2. A 45 GHz bandwidth was obtained with a low dark current density of 0.8 nA/µm2. Moreover, a more than 20 GHz bandwidth was achieved with zero-bias voltage. In the case of zero-bias voltage operation, a 3 dB bandwidth was a little affected by input power, which would originate from the photocarrier screening effect on the built-in electric field.
04CG11
Liao Zhang, Michio Ikezawa, Tatsuya Mori, Shintaro Umehara, Yoshiki Sakuma, Kazuaki Sakoda and Yasuaki Masumoto
We studied optical properties of isoelectronic traps in nitrogen δ-doped GaAs by micro-photoluminescence (µ-PL) spectroscopy. We found that these nitrogen impurity centers (NNA) emit photons with nearly identical emission energy at 1475 meV and polarization direction. Furthermore, single photon generation from a single impurity center was confirmed by a strong photon antibunching under the continuous optical excitation at 5 K. Our results suggest that the nitrogen impurity center in GaAs might be well suited for the energetically-defined single photon source for the quantum information application.
04CG12
Sang-Baie Shin, Hiroto Sekiguchi, Hiroshi Okada and Akihiro Wakahara
In this study, the prototype optoelectronic integrated circuits (OEICs) operating with optical input signals were designed and fabricated. A back-side-illuminated (BSI) photodiode was designed and demonstrated by a newly proposed practical method, utilizing micro-electromechanical systems (MEMS) and postcomplement metal oxide semiconductor (CMOS) processes. Additional fabrication processes for the BSI photodiode were proposed and described in detail in this paper. The operational amplifier for amplification of the optical current by the BSI photodiode as the transimpedance amplifier was designed and fabricated. And the pulse width modulation (PWM) wave generator was implemented for modulating optical signals as the prototype OEIC device. The maximum quantum efficiency of 28.4% was obtained from the fabricated BSI photodiode. Output signals of PWM were successfully controlled by the generated optical current of the BSI photodiode.
04CG13
Fumihiko Tanoue, Hiroharu Sugawara, Kouichi Akahane and Naokatsu Yamamoto
A 147-µm-long cavity laser diode with 19 InGaAs quantum dot layers was fabricated by the ultrahigh-rate molecular beam epitaxial growth technique, and its gain properties were investigated using the Hakki–Paoli method below the threshold current (Ith) of 111.5 mA. At an injection current of 100.3 mA (0.9Ith), the positive net modal gain was in the range between 1005 and 1043 nm, corresponding to a photon energy of 45 meV. The maximum net modal gain and maximum modal gain were 46.5 and 60.5 cm-1, respectively. A differential net modal gain of as high as 3.8 cm-1/mA was observed at 0.77 times the threshold current. No gain saturation appeared below the threshold current, and injection currents higher than 78.4 mA (≈0.7Ith) were required to obtain a net modal gain.
04CG14
Ming Chang Shih, Yu Chin Sun and Shin Wei Fan
We demonstrated an InGaAlP multiple-quantum-well semiconductor laser diode with double circular ring cavities and its output characteristics. It was found that the optical confinement factor of the ridge waveguide plays an important role in the output emission of this device, and superluminescence emission can be achieved with a low-confinement ridge waveguide. Spatial solitons can be generated in the ridge waveguide of 8 µm width and 0.9 µm depth owing to a nonlinear photorefractive effect. When the injection current in the circular ring cavity increases, the feedback light from the Y-junction coupling section continuously enhances the excitation through the soliton waveguide. In addition, the double-ring cavities provide wavelength filtering and feedback control from the Y-junction coupling section to achieve a superluminescent mode or lasing mode output operation. Results of light–current (L–I) and spectral measurements of the devices with various waveguide properties were presented to explore the mechanism of the output from this circular ring laser diode.
04CG15
Yasushi Nanai, Yu Sakamoto and Tsuyoshi Okuno
The luminescence properties of rare-earth-doped thiosilicate phosphors are reported. These thiosilicate materials are fabricated in phosphor layers on silicon substrates. For Eu2+-doped calcium thiosilicate, yellow (560 nm) and red (650 nm) bands are obtained in the photoluminescence spectrum, which is almost the same as that for the corresponding powder sample. The energy transfer efficiency from Eu2+ to Er3+ in Eu2SiS4:Er3+ on Si substrates is improved by optimization of the annealing conditions. In addition, the insulation of electroluminescence devices using BaSi2S5:Eu2+ on silicon-on-insulator substrates is improved using a high-dielectric-constant polymer as a transparent insulating layer.
Advanced material synthesis and crystal growth technology
04CH01
Makoto Takamura, Kazuaki Furukawa, Hajime Okamoto, Shinichi Tanabe, Hiroshi Yamaguchi and Hiroki Hibino
We report on the mechanical resonance properties of trilayer graphene resonators created by controlling of the layer number. We epitaxially create bilayer graphene and an interfacial buffer layer on a SiC substrate. Using hydrogen intercalation combined with electrochemical etching, we break the Si–C bonds between the buffer layer and SiC substrate surface so that the bilayer graphene and buffer layer turn into three graphene layers. The successful creation of the trilayer graphene resonators is directly observed with a transmission electron microscope. By investigating the frequency shift induced by the laser irradiation, we estimate the thermal expansion coefficient. We find that a quality factor shows a typical temperature dependence of monolayer graphene and carbon-nanotube resonators with a doubly-clamped beam structure. This implies that there exists a general energy loss mechanism for both nanotubes and few-layer-graphene doubly clamped resonators.
04CH02
Kyoichi Kinoshita, Osamu Nakatsuka, Yasutomo Arai, Keisuke Taguchi, Hiroshi Tomioka, Ryota Tanaka and Shinichi Yoda
Compositionally uniform 2 and 10 mm diameter Si0.5Ge0.5 bulk crystals have been grown by the traveling liquidus-zone (TLZ) method. The TLZ method requires diffusion controlled mass transport in a melt and crystal size was limited for suppressing convection in a melt. For substrate use, however, larger diameter crystals are required. Increase of crystal diameter was challenged in spite of the concern that compositional homogeneity of grown crystals might be degraded due to faster convective flow in a larger diameter melt. As a result, however, increase of crystal diameter was possible up to 30 mm although single crystal length was limited to 5 mm. Si0.55Ge0.45 and Si0.6Ge0.4 bulk crystals with 30 mm diameter showed excellent compositional homogeneity and high crystallinity without mosaicity.
04CH03
Takeshi Kawae, Yuichiro Seto and Akiharu Morimoto
(Bi,Pr)(Fe,Mn)O3 (BPFM) thin films were deposited on SiO2/Si substrates by a chemical solution deposition method, resulting in the metal–ferroelectric–insulator–semiconductor (MFIS) capacitor structure. Polycrystalline BPFM films were grown on the substrate without impurity phases. Comparing with the capacitance vs voltage (C–V) curves of the MFIS capacitor structures with and without the BPFM self-barrier layer, the BPFM self-barrier layer suppress the formation of charge trap sites in the interface between the BPFM and SiO2 layers of the present structure, resulting in the prepared MFIS capacitor structure showing a clockwise C–V hysteresis behavior due to remnant polarization of the BPFM layer. The memory window width in the C–V curve was approximately 0.5 V for the bias voltage sweep from -20 to +20 V.
04CH04
Takahiro Hamada, Akihiro Ito, Nobuaki Nagao, Nobuyasu Suzuki, Eiji Fujii and Ayumu Tsujimura
We report on the structural and electrical properties of ZnO films grown on surface-treated GaN/Al2O3 substrates by chemical bath deposition. X-ray diffraction analysis indicated that the ZnO films had a single-crystalline wurtzite structure with c-axis orientation. The ZnO film exhibited n-type conduction with a carrier concentration of 6.9 ×1018 cm-3, an electron mobility of 41 cm2/(V·s), and a resistivity of 2.2 ×10-2 Ω·cm. A low specific contact resistivity of 4.3 ×10-3 Ω·cm2 was obtained at the ZnO/n-GaN interface. Additionally, the ZnO film exhibited high transparency in the visible and infrared region.
04CH05
Fumiya Ishizaka, Keitaro Ikejiri, Katsuhiro Tomioka and Takashi Fukui
We studied the growth of indium-rich InGaP nanowires (NWs) on InP (111)A substrates by selective-area metal organic vapor phase epitaxy (SA-MOVPE). We obtained vertically aligned InGaP NWs by optimizing growth conditions, such as group III supply ratio and V/III ratio. We found that the height, diameter, shape, and composition of InGaP NWs depended significantly on the supply ratios of trimethylgallium (TMGa) and trimethylindium (TMIn). As the supply ratio of TMGa was increased, the lateral growth was drastically enhanced, and the uniformity of NWs deteriorated. Furthermore, the sidewall facets of NWs changed from {211} to {110} as the supply ratio of TMGa was increased, indicating the possibility of structural transition from wurtzite (WZ) to zinc blende (ZB). We propose a possible growth model for such lateral growth, uniformity, and structural transition. Photoluminescence (PL) measurements revealed that the Ga compositions ranged approximately from 0 to 15%. Our results show that highly uniform InGaP NWs can be grown by controlling the growth conditions.
04CH06
Yu-Ci Jian, Der-Yuh Lin, Jenq-Shinn Wu and Ying-Sheng Huang
Single crystals of Au- and Ag-doped ReSe2 (ReSe2:Au and ReSe2:Ag) have been grown by chemical vapor transport (CVT) method using iodine as a transporting agent. The optical properties are studied by absorption and polarized-thermoreflectance (PTR) spectroscopy at different polarization angles in the temperature range between 12 and 300 K. The direct band-edge excitonic transitions (E1ex, E2ex, E3ex, and Esex) have been clearly revealed for the first time in the absorption spectra when the samples are made thin enough. The dominant E1ex and E2ex excitonic transitions gets strongest as the polarization is parallel and perpendicular to the b-axis, respectively. The parameters that describe the temperature dependence of the excitonic transition energy and the broadening function are extracted and discussed. We have also performed electrical conductivity and Hall measurements at different temperatures to derive the activation energy (∼95 and 50 meV for ReSe2:Au and ReSe2:Ag, respectively).
04CH07
Tetsuya Kouno, Masaru Sakai, Katsumi Kishino and Kazuhiko Hara
Hexagonal GaN microdisks exhibiting lasing action with unusual wavelengths of approximately 390 nm under an optically pumped condition have been investigated. The lasing action was caused by the resonant modes of the whispering gallery mode and/or quasi-whispering gallery mode in the hexagonal microdisks. A cross-sectional transmission electron microscopy observation indicated that multiple crystalline boundaries, which are formed by stacking faults, were included in the specific GaN microdisks exhibiting such an unusual lasing action. The origin of the optical gain was discussed, based on the modification of the crystal structure associated with the stacking faults.
04CH08
Susoma Jannatul Ferdous, Yoshifumi Nakamine, Tetsuo Kodera, Koichi Usami, Yukio Kawano and Shunri Oda
Silicon nanocrystal (SiNC)-based thin-film devices have been fabricated, where the idea of scaling down of channel length was implemented in such a way that very few SiNCs can be fitted inside the channel in the channel length direction in order to decrease the number of barriers to increase electrical conductivity. In this study, we have demonstrated the scaling down of channel length to 20 nm in order to reduce the number of barriers provided by each of the SiNCs, which are fabricated using a very high-frequency (VHF) plasma-enhanced chemical vapor deposition (CVD) system with a diameter of 10±1 nm. A high electrical conductivity has been achieved by optimizing channel length. In addition, we have demonstrated the surface nitridation of SiNCs to protect the highly reactive surface of SiNCs from further natural oxidization and successfully suppressed the degradation of transport properties.
04CH09
Takahiro Oikawa, Shintaro Yasui, Takayuki Watanabe, Koji Ishii, Yoshitaka Ehara, Hisato Yabuta, Takeshi Kobayashi, Tetsuro Fukui, Kaoru Miura and Hiroshi Funakubo
Films of a high-pressure perovskite phase, Bi(Mg1/2Ti1/2)O3, were prepared on (111)c-oriented SuRuO3-coated (111)Pt/TiO2/SiO2/(100)Si substrates. The perovskite Bi(Mg1/2Ti1/2)O3 films had a (111) one-axis orientation, because their constituent grains were epitaxially grown on (111)c-oriented perovskite SrRuO3 ones. The remanent polarization and piezoelectric constant measured at an applied electric field of 600 kV/cm were about 30 µC/cm2 and 40 pm/V, respectively. A remarkable phase transition was not observed from room temperature to 350 °C in a (111) one-axis-oriented Bi(Mg1/2Ti1/2)O3 film, suggesting that the Curie temperature of this film is above 350 °C.
04CH10
Gerald Lucovsky
The following topics are addressed: (i) X-ray absorption spectroscopy (XAS) studies of plasma deposited non-crystalline (nc-) SiO2 and GeO2 emphasizing (a) band-edge states and (b) pre-existing bonding defects, and (ii) interpretation of X-ray absorption and photoemission spectra based on many electron theory, including two-electron singlet and triplet electron spin states. The articles also addresses electronic and defect structures in emerging device structures incorporating (GeO2)x(SiO2)1-x alloys, and bonding between Ge and Si substrates and elemental and/or alloy nc-SiO2 and nc-GeO2. The most significant results are identification of local atomic structure of pre-existing defects in the elemental oxides. Defects are created during processing, and are qualitatively different than those produced by X-ray, γ-ray, or high energy electron stressing and detected by second derivative XAS.
04CH11
Chih-Cheng Huang, Chen-Chia Kao, Der-Yuh Lin, Chih-Ming Lin, Fan-Lei Wu, Ray-Hua Horng and Ying-Sheng Huang
We present a comprehensive study on the optical properties of gold-doped rhenium disulphide (ReS2:Au) layer crystal. Its anisotropic optical properties were studied by using the polarization-dependent optical absorption and photoconductivity (PC) measurements. Absorption measurements indicate that the absorption edge shifted toward high energy as the sample was slimmed down to a thin piece. For the first time, excitonic transitions have been observed by this method. The room temperature transition energies were evaluated to be 1.48 eV for E1ex and 1.516 eV for E2ex. E1ex exciton dominates the transition as the polarization is parallel to the b-axis of the layer crystal, while E2ex exciton is most present as the polarization is perpendicular. PC spectra are performed to check this anisotropic phenomenon. Thermoreflectance modulation (TR) and photoluminescence (PL) measurements have been performed in the temperature range of 42 to 300 K. The temperature dependence of the transition energies and broadening parameters were determined.
Physics and applications of novel functional devices and materials
04CJ01
Tomohiro Kambara, Tetsuo Kodera, Yasuhiko Arakawa and Shunri Oda
We demonstrate gating and charge sensing functions of a lithographically defined single electron transistor (SET). The electrochemical potential of the SET is modulated by applying a voltage to both the source and drain electrodes. The SET integrated with a double quantum dot (DQD) works as a gate electrode for the DQD. Charge transitions in the DQD are detected by the SET through its charge sensing function. This dual function of the SET is useful for saving space in crowded devices with many gates and charge sensors, toward the integration of multiqubits for quantum computation.
04CJ02
Shiu-Ming Huang, Alexander Olegovich Badrutdinov, Kimitoshi Kono and Keiji Ono
We study the spin splitting energies of different orbital states of quantum dots with a low-potential barrier. The experimental results show that the splitting energies are orbital state dependent. The theoretical analysis is done with a generalization of the Fock–Darwin states in the presence of spin–orbit interactions. The theoretical predictions match well with the experimental observations and exhibits that the Rashba interaction strength in vertical In0.05Ga0.95As/GaAs quantum dots is in the range 80≤λR≤120 meV Å. This enhanced Rashba spin–orbit interaction intensity can be understood from the high penetration of the electron wavefunction into the quantum well with a low-potential barrier.
04CJ03
Tetsufumi Tanamoto, Yu-xi Liu, Xuedong Hu and Franco Nori
The Kondo effect and the Fano–Kondo effect are important phenomena that have been observed in quantum dots (QDs). We theoretically investigate the transport properties of a coupled QD system in order to study the possibility of detecting a qubit state from the modulation of the conductance peak in the Kondo effect and the dip in the Fano–Kondo effect. We show that the peak and dip of the conductance are both shifted depending on the qubit state. In particular, we find that we can estimate the optimal point and tunneling coupling between the |0> and |1> states of the qubit by measuring the shift of the positions of the conductance peak and dip, as functions of the applied gate voltage on the qubit and the distance between the qubit and the detector.
04CJ04
Nobuya Mori, Masanori Tomita, Hideki Minari, Takanobu Watanabe and Nobuyoshi Koshida
Impacts of atomic disorder on avalanche multiplication in a one-dimensional silicon nanodot (SiND) array have been theoretically studied. The disorder lifts the degeneracy of the energy levels and reduces the impact-ionization threshold. This leads to a larger carrier multiplication factor in the disordered SiND array compared to an ideal SiND array without disorder or strain.
04CJ05
Ryota Suzuki, Motoki Nozue, Takuya Saraya and Toshiro Hiramoto
Silicon-based single-electron transistors (SETs) and complementary metal–oxide–semiconductor (CMOS) devices have been integrated onto a single chip, and the operation of SET/CMOS integrated circuits has been demonstrated at room temperature. The fabrication process of SETs has been improved in terms of parasitic resistance suppression, threshold voltage control, and reduction in required time for electron-beam lithography for integration with CMOS devices. There is no significant degradation in the characteristics of CMOS devices owing to the special fabrication process of SETs operating at room temperature. CMOS 1-bit analog selectors, which are building blocks of multibit address decoders, have been combined with SETs, and the circuit operation has been demonstrated at room temperature for the first time. These results show the feasibility of SET/CMOS integrated circuits composed of high-density arrays of SETs and high-performance CMOS peripheral circuits, which fully leverage the advantages of SETs and CMOS.
04CJ06
Taro Shiokawa, Genki Fujita, Yukihiro Takada, Satoru Konabe, Masakazu Muraguchi, Takahiro Yamamoto, Tetsuo Endoh, Yasuhiro Hatsugai and Kenji Shiraishi
Influence of Coulomb blockade on electron scattering by a quantum dot has been theoretically investigated using a multielectron wave packet simulation technique based on the time-dependent Hartree–Fock approximation. In our simulation, the bound states of electrons in the dot are self-consistently determined. We confirmed that Koopman's theorem keeps its validity only for weak Coulomb interactions. Moreover, we show that the maximum number of electrons trapped in the dot does depend on the strength of Coulomb interactions. Consequently, the transmission and reflection probabilities of an incident wave packet toward the dot are strongly influenced by the number of trapped electrons in the dot.
04CJ07
Junya Denda, Kazuya Uryu and Masahiro Watanabe
A novel scheme of resistance switching random access memory (ReRAM) devices fabricated using Si/CaF2/CdF2/CaF2/Si quantum-well structures grown on metal CoSi2 layer formed on a Si substrate has been proposed, and embryonic write/erase memory operation has been demonstrated at room temperature. It has been found that the oxide-mediated epitaxy (OME) technique for forming the CoSi2 layer on Si dramatically improves the stability and reproducibility of the current–voltage (I–V) curve. This technology involves 10-nm-thick Co layer deposition on a protective oxide prepared by boiling in a peroxide-based solution followed by annealing at 550 °C for 30 min for silicidation in ultrahigh vacuum. A switching voltage of lower than 1 V, a peak current density of 32 kA/cm2, and an ON/OFF ratio of 10 have been observed for the sample with the thickness sequence of 0.9/0.9/2.5/0.9/5.0 nm for the respective layers in the Si/CaF2/CdF2/CaF2/Si structure. Results of surface morphology analysis suggest that the grain size of crystal islands with flat surfaces strongly affects the quality of device characteristics.
04CJ08
Toru Miyabe and Toshihiro Nakaoka
We report unipolar and bipolar resistive switchings in naturally oxidized AlxO1-x thin films. We find a relationship between the switching behavior and the electrode gap distance. The macro-gap device with the electrode separation of 20 µm shows a unipolar switching behavior while the nano-gap device with the separation of 40 nm shows a bipolar behavior. The result is explained by a model in which the unipolar or the bipolar switching is governed by the way of the carrier injection into oxygen vacancies.
04CJ09
Chih-Ting Lin, Jer-Chyi Wang, Po-Wei Huang, Yu-Yen Chen and Li-Chun Chang
The annealing effects on the gold nanocrystal (Au-NC) formation for memory application are proposed. At higher annealing temperatures, the memory window becomes larger owing to the high density of Au-NCs. The average size of the Au-NCs is approximately 5 nm, and the spaces between NCs tend to decrease with annealing temperature. Furthermore, the retention charge loss rate was optimized at 700 °C annealing formation and found to be dominated by the thermally activated and tunneling mechanisms. The high charge loss rate for the thermally activated mechanism shows no dependence on annealing temperature, while the low charge loss rate for the tunneling depends on the spaces between NCs. Besides, the activation energy of the thermally activated electron loss was low at a high Au-NC density, which can be attributed to the lateral electron migration between NCs. The endurance of the 700 °C annealed sample can sustain a memory window of approximately 1.1 V after 104 program/erase cycles.
Organic materials science, device physics, and applications
04CK01
Hirotake Kajii, Daiki Terashima, Yusuke Kusumoto, Ikuya Ikezoe and Yutaka Ohmori
We investigated the fabrication and electrical and optical properties of top-gate-type polymer light-emitting transistors with the surfaces of amorphous fluoropolymer insulators, CYTOP (Asahi Glass) modified by vacuum ultraviolet light (VUV) treatment. The surface energy of CYTOP, which has a good solution barrier property was increased by VUV irradiation, and the gate electrode was fabricated by solution processing on the CYTOP film using the Ag nano-ink. The influence of VUV irradiation on the optical properties of poly(9,9-dioctylfluorene-co-benzothiadiazole) (F8BT) films with various gate insulators was investigated to clarify the passivation effect of gate insulators. It was found that the poly(methyl methacrylate) (PMMA) film prevented the degradation of the F8BT layer under VUV irradiation because the PMMA film can absorb VUV. The solution-processed F8BT device with multilayer PMMA/CYTOP insulators utilizing a gate electrode fabricated using the Ag nano-ink exhibited both the ambipolar characteristics and yellow-green emission.
04CK02
Tadahiko Hirai, Karl Weber, Jenny O'Connell, Mark Bown and Kazunori Ueno
We propose a novel Schottky and impedance spectroscopy (IS) numerical model to evaluate carrier injection and transport behavior of organic semiconductor materials. Using temperature-dependent current–voltage (I–V) and IS measurements of hole-only (HOD) and electron-only (EOD) devices and phosphorescent blue organic light emitting diodes (OLEDs), we have obtained values for the Richardson factor, the barrier height, trap density, density of states (DOS), and carrier mobility of organic materials and interfaces as device parameters. Therefore, we approach to degradation mechanism of the emitting zone inside of the OLEDs.
04CK03
Yu-Sheng Tsai, Apisit Chittawanij, Fuh-Shyang Juang, Lin-Ann Hong and Chih-Yuan Ou
Solution-based processing was applied to fabricate green phosphorescent organic light-emitting diodes (OLEDs). EPH31 was used as a phosphorescent host, doped with guest dopant green phosphorescent Ir(ppy)3, and dissolved in chlorobenzene solvent to form the emitting layer. Device structural parameters were controlled by changing the spin coating speed of the emitting layer and hole injection layer [poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate), PDOT:PSS] to adjust the thickness of the electron transport layer [tris(8-hydroxyquinolinato)aluminum, Alq3]. In addition, the differences in using CsF and LiF materials as the electron injection layer were investigated. A maximum current efficiency of 13.6 cd·A-1 was obtained at a high emitting layer spin coating speed. Despite the close resemblance in both the luminance intensity and current efficiency when using CsF and LiF as the electron injection layer, CsF devices had a low driving voltage. Smooth and stable films resulting from the spin coated hole injection layer, along with the control of the thickness of the electron transport layer (Alq3) and electron injection layer (CsF), effectively improved the performance of green OLEDs. The emitting layer host material (CBP) and three guest dopants [Firpic, Ir(ppy)3, and Ir(piq)2] were dissolved in toluene solvent during solution preparation to fabricate white OLEDs. The properties of the resulting solution-processed white PHOLEDs are a current efficiency of 2.4 cd·A-1 at 20 mA·cm-2 and CIE coordinates of (0.33, 0.33) at 9 V. Results of these experiments demonstrate that solution processing can be used as an alternative to and in conjunction with thermal evaporation.
04CK04
Dai Taguchi, Takaaki Manaka, Mitsumasa Iwamoto, Tetushu Karasuda and Mikio Kyomasu
We have developed a novel microscope for visualizing electric fields in organic thin film devices on the basis of electric-field-induced second-harmonic generation (EFISHG) measurement. By using a radial polarized laser beam as a probing light, we showed that the electric field formed in metal–C60–metal diodes in the film-thickness direction is visualized. The developed microscope has a potentiality in directly visualizing carrier motion in thin-film devices such as organic solar cells.
04CK05
Eiji Itoh, Yasutake Maruyama and Katsutoshi Fukuda
The contributions of ultrathin titania nanosheet (TN) crystallites were studied in both an inverted bulk-heterojunction (BHJ) cell in indium tin oxide (ITO)/titania nanosheet (TN)/poly(3-hexylthiophene) (P3HT):phenyl-C61-butyric acid methylester (PCBM) active layer/MoO3/Ag and a conventional BHJ cell in ITO/MoO3/P3HT:PCBM active layer/TN/Al multilayered photovoltaic devices. The insertion of only one or two layers of poly(diallyldimethylammonium chloride) (PDDA) and TN multilayered film prepared by the layer-by-layer deposition technique effectively decreased the leakage current and increased the open circuit voltage (VOC), fill factor (FF), and power conversion efficiency (η). The abnormal S-shaped curves observed in the inverted BHJ cell above VOC disappeared with the reduction in the work function of the bottom electrode in the inverted cells. The power conversion efficiency was increased nearly twofold, and better photovoltaic performance was observed in the conventional BHJ cells. Although the active layer has a hydrophobic surface, the active layer was fully covered by the insertion of only two or three layers of PDDA/TN multilayered film. The TN layer effectively decreased the leakage current by a factor of 100, and increased the open circuit voltage by 0.25 V probably owing to the complete hole blocking at the P3HT/TN/Al interface.
04CK06
Kosuke Sugawa, Daido Tanaka, Tomonori Ichikawa and Naoto Takeshima
In this study, we have developed localized surface plasmon resonance (LSPR) refractive index sensor systems consisting of triangular silver nanoplates (nanoprisms) immobilized on glass plates by electrostatic interactions. The nanoprisms are synthesized by exploiting light-induced morphological changes in silver nanoparticles in aqueous solution. We have demonstrated that silver nanoprisms protected with alkylthiol molecules and supported by glass plates can function as spectrally stable LSPR refractive index sensors even in ethanol solvents. The sensitivity of the nanoprisms was found to increase with decreasing carbon chain length of alkylthiol. Furthermore, we have demonstrated that nanoprisms with higher aspect ratios had higher sensitivities than those with lower aspect ratios.
04CK07
Ryuji Matsumoto, Sunao Yamada and Hiroaki Yonemura
The fabrication of tetraphenyl porphyrin (TPP)–silver nanoparticle (AgP) composite films on indium–tin oxide (ITO) electrodes was carried out by the electrostatic layer-by-layer adsorption technique. Maximum enhancement in photocurrent action spectra as well as in fluorescence emission spectra was observed at an immersion time of 2 h. The effects of AgP on photocurrent and fluorescence suggested the effects of enhanced electric fields resulting from a localized surface plasmon resonance on the enhancement of photocurrent and fluorescence signals. The effect of AgP on the lifetime of the singlet excited state of TPP (1TPP*) indicated that the lifetime of 1TPP* decreases as compared with that in the absence of AgP substrate. The results on fluorescence lifetime suggested that the difference between the effects of AgP on photocurrent and fluorescence is most likely ascribed to the notion that the energy transfer from 1TPP* to surface plasmons due to AgP aggregates competes with photoinduced electron transfer from 1TPP* to O2 during photocurrent measurement.
04CK08
Keanchuan Lee, Martin Weis, Xiangyu Chen, Dai Taguchi, Takaaki Manaka and Mitsumasa Iwamoto
Effects of illumination on the carrier injection and transport due to photogenerated carriers were investigated in pentacene organic field-effect transistor (OFET). A plasmonic nanoparticles self-assembled monolayer (SAM) was incorporated in pentacene FET to act to enhance the photo-carrier generation. The influence of nanoparticles (NPs) on the photogeneration as well as on the charge trapping has been investigated using the current–voltage (I–V) and impedance spectroscopy (IS) measurements. The I–V results proved higher amount of photogenerated charge in presence of NPs even though this device has the contact resistance about two orders higher and effective mobility an order lower than the reference device without plasmonic NPs. The IS analysis of relaxation times verified strong influence of NPs on the charge trapping.
04CK09
Shui-Hsiang Su, Chung-Ming Wu, Hsiang-Lin Tsai and Meiso Yokoyama
This work presents transparent pentacene-based organic thin film transistors (OTFTs) in which an oxide/metal/oxide trilayer provides low-resistance transparent source/drain electrodes. The device structure is glass/indium–tin oxide (ITO)/poly(methyl methacrylate) (PMMA)/pentacene/transparent source–drain electrode. The transparent source/drain electrode consists of a low-resistance metal, silver, that is sandwiched by a high-transmittance oxide, WO3. The structure of the transparent source–drain electrode is optimized by tuning the thickness of each layer. The optimized structure has a sheet resistance of 6.2 Ω/sq. and an optimum transmittance of 70% in the visible wavelength range of 380–780 nm. The pentacene-based OTFT employing optimized transparent source–drain electrode yields an output current (IDS) of -7.08 µA, a field-effect mobility (µ) of 0.22 cm2 V-1 s-1, an on–off drain current ratio of 1.8×105, and a threshold voltage of -15.1 V. OTFTs in which WO3 (5 nm)/Ag (10 nm)/WO3 (30 nm) is used as the source/drain electrode greatly outperform OTFTs in which silver is utilized, because the work function of WO3/Ag/WO3 substantially exceeds that of silver.
04CK10
Taikai Eguchi, Yuusuke Tsuchiya, Ai Hasegawa, Kuniaki Tanaka, Kenji Ogino and Hiroaki Usui
Thin films of poly(3,4-ethylenedioxythiophene) (PEDOT) were obtained by physical vapor deposition. To this end, low-molecular-weight PEDOT was synthesized by oxidative polymerization using oxygen as the oxidizing reagent with palladium acetate and copper acetate as the catalysts. The degree of polymerization was controlled by adjusting reaction time. The material can be vapor-deposited by thermal evaporation when the degree of polymerization was about 10. Formation of PEDOT thin films was confirmed by infrared spectroscopy. The optical absorption edge of the deposited film showed a redshift with increasing degree of polymerization. The electrical conductivity of the deposited film was in the range from 10-4 to 10-3 S/cm. The deposited films are expected to be in the nondoped state since the oxidizing reagent (oxygen) is unlikely to remain in the films.
04CK11
Shun-ichiro Ohmi, Kousuke Kamino and Hiroshi Ishiwara
Ultrathin poly(4-vinylphenol) (PVP) layer formation by evaporation was investigated for the first time to improve the pentacene/HfO2 interface characteristics in bottom-gate organic field-effect transistors (OFETs). 3–10-nm-thick PVP layers were successfully deposited by evaporation. It was found that the surface roughness of the PVP layer was remarkably decreased at the deposition temperatures of 50–100 °C both on SiO2 and HfO2 gate insulators. The obtained relative dielectric constants of the PVP layers deposited on SiO2 and HfO2 were 3.4 and 4.8, respectively. The mobility in the fabricated pentacene-based p-type OFETs with the HfO2 gate insulator was increased from 0.25 cm2 to 0.32 cm2 V-1 s-1 at the operation voltage of 2 V by the 5-nm-thick PVP interfacial layer deposited at 50 °C.
Micro/Nano electromechanical systems and bio/medical analyses
04CL01
Yuki Nishio, Shigeyasu Uno and Kazuo Nakazato
Full three-dimensional simulation of DNA detection by ion-sensitive field-effect transistor technology is presented. DNA conditions for improving the sensing characteristics, namely, increased hybridization signal, are clarified. Poisson's equation is solved using a full three-dimensional finite element method for the model, where the model space consists of an electrolyte, DNAs, a self-assembled monolayer, and an insulator. The flatband voltage shift due to the hybridization of randomly positioned and oriented DNA is similar to experimental data, and indicates the possibility of experimental prediction. We examine the effects of DNA position and orientation on flatband voltage shift, and it is noted that the hybridization signal becomes largest when the DNAs are tilted 90° and distributed at equal intervals. It is also noted that a large hybridization signal can be obtained when upright DNAs are tightly immobilized even if it is difficult to tilt the DNAs.
04CL02
Hui-Chong Lau, Tae-Eon Bae, Hyun-June Jang, Jae-Young Kwon, Won-Ju Cho and Jeong-Ok Lim
The development of potential applications of biosensors using the sensory systems of vertebrates and invertebrates has progressed rapidly, especially in clinical diagnosis. The biosensor developed here involves the use of Drosophila cells expressing the gustatory receptor Gr5a and an ion-sensitive field-effect transistor (ISFET) sensor device. Gustatory receptor Gr5a is expressed abundantly in gustatory neurons and acts as a primary marker for tastants, especially sugar, in Drosophila. As a result, it could potentially serve as a good candidate for potential biomarkers of diseases in which the current knowledge of the cause and treatment is limited. The developed ISFET was based on the outstanding electrical characteristics of the metal–oxide–semiconductor field-effect transistor (MOSFET) with a subthreshold swing of 85 mV/dec, low leakage current of <10-12 and high on/off current ratio of 7.3×106. The SiO2 sensing membrane with a pH sensitivity of 34.9 mV/pH and drift rate 1.17 mV/h was sufficient for biosensing applications. In addition, the sensor device also showed significant compatibility with the Drosophila cells expressing Gr5a and their response to sugar, particularly trehalose. Moreover, the interactions between the transfected Drosophila cells and trehalose were consistent and reliable. This suggests that the developed ISFET sensor device could have potential use in the future as a screening device in diagnosis.
04CL03
Chikashi Kigure, Hideki Naganuma, Yuichiro Sasaki, Hisashi Kino, Hiroshi Tomita and Tetsu Tanaka
The development of poly(3,4-ethylenedioxythiophene) (PEDOT) stimulus electrodes and the relationship between the electrical stimulation of a rabbit retina and electrically evoked potential (EEP) were studied in detail. We fabricated implantable flexible cables with Pt, IrOx, and PEDOT electrodes and evaluated the electrochemical impedances (EIs) and charge injection capacities (CICs) of such electrodes. From the result, we confirmed that PEDOT electrodes have both lower EIs and larger CICs than Pt and IrOx electrodes. In addition, we performed in vivo experiments with PEDOT electrodes and clarified the relationships between the electrical stimulation of the rabbit retina and EEP. It is highly probable that visual restoration will be realized safely with PEDOT electrodes.
04CL04
Sanghoon Lee, Soichiro Kanno, Hisashi Kino and Tetsu Tanaka
We have fabricated various types of Si neural probe for in vivo and in vitro neuronal signal recordings by combining standard photolithography with a bulk micromachining process. To place the probe tip at target areas in the brain precisely, the mechanical properties of the Si neural probes with various tip shapes were carefully investigated under different insertion conditions to brain phantoms. As results, the minimum length and penetration force of the Si neural probe were determined from conditions where the Si neural probe began to penetrate the surface of the brain phantom. To control buckling of the Si neural probe, it is necessary to optimize the insertion rate in accordance with the conditions of the Si neural probe. Although the insertion forces of the Si neural probe with a sharpened tip were smaller than those of the Si neural probe with a normal tip, the effect of the probe tip shape became small with increased insertion speeds.
04CL05
Subrata Kumar Kundu, Shinya Kumagai and Minoru Sasaki
Realizing an untethered, low-cost, and comfortably wearable respiratory rate sensor for long-term breathing monitoring application still remains a challenge. In this paper, a conductive-textile-based wearable respiratory rate sensing technique based on the capacitive sensing approach is proposed. The sensing unit consists of two conductive textile electrodes that can be easily fabricated, laminated, and integrated in garments. Respiration cycle is detected by measuring the capacitance of two electrodes placed on the inner anterior and posterior sides of a T-shirt at either the abdomen or chest position. A convenient wearable respiratory sensor setup with a capacitance-to-voltage converter has been devised. Respiratory rate as well as breathing mode can be accurately identified using the designed sensor. The sensor output provides significant information on respiratory flow. The effectiveness of the proposed system for different breathing patterns has been evaluated by experiments.
Spintronics materials and devices
04CM01
Aurélie Spiesser, Suguru Watanabe, Hidekazu Saito, Shinji Yuasa and Koji Ando
We examined electrical creation of spin-polarized carriers in heavily doped p-type Ge from a Fe/GeO2 tunnel contact where GeO2 is an amorphous insulator. Clear spin accumulation signals were successfully observed up to 300 K down to a very low voltage of 1 mV. In contrast to epitaxial Fe/MgO tunnel contact, the magnitude of spin accumulation signal exhibits a nearly symmetric behavior with respect to the bias voltage polarity. These results establish that GeO2 is an effective tunnel barrier for spin injection and detection in germanium.
04CM02
Yuichi Fujita, Shinya Yamada, Gotaro Takemoto, Soichiro Oki, Yuya Maeda, Masanobu Miyao and Kohei Hamaya
To inform room-temperature spin functionality of D03-ordered Fe3Si, we explore tunneling magnetoresistance (TMR) effects in magnetic tunnel junctions (MTJs) consisting of Co60Fe40/AlOx/Fe3Si on Si. We clearly observe reproducible TMR ratios of ∼20% at room temperature for all MTJs fabricated. By using Julliere's formula, the room-temperature spin polarization (P) value for D03-ordered Fe3Si can be roughly estimated to be ranging from 0.18 to 0.45 when we assume the P values from 0.5 to 0.2 for Co60Fe40. This study reveals that the room temperature P value for D03-ordered Fe3Si is relatively small compared with that for Co-based Heusler alloys reported previously.
04CM03
Tetsufumi Tanamoto, Hideyuki Sugiyama, Tomoaki Inokuchi, Mizue Ishikawa and Yoshiaki Saito
Spin injection and detection are very sensitive to the interface properties between ferromagnet and semiconductor. Because the interface properties such as a tunneling resistance and a polarization factor can be chosen independently between the injection and detection sides, the magnetic transport properties are considered to depend on the asymmetry of the two interfaces. We theoretically investigate the effect of the asymmetric interfaces of the injection side and the detection side on both the local and non-local magnetoresistance measurements. The results show the magnetoresistance ratio of local measurement structure has its maximum at the symmetric structure, and the effect of the asymmetry is very weak for the non-local measurement structure.
04CM04
Daisuke Suzuki, Yuhui Lin, Masanori Natsui and Takahiro Hanyu
A single-ended circuit using three-terminal magnetic tunnel junction (3T-MTJ) devices is proposed for a compact nonvolatile lookup-table (NV-LUT) circuit. The use of 3T-MTJ devices makes a high tunnel magneto-resistance ratio used in the circuit, because read-current path is separated from the write-current path. By utilizing single-ended circuit structure, the NV-LUT circuit becomes quite simple without reference circuit. In fact, the effective area of the proposed 6-input NV-LUT circuit is only 29% the size of the corresponding CMOS-based implementation using two-terminal-MTJ-based nonvolatile static random access memory cells, with a simulation program with integrated circuit emphasis (SPICE) simulation under a 90 nm CMOS technology.
04CM05
Ryo Yamaguchi, Shin-ichiro Gozu, Teruo Mozume, Yoshitsugu Oyanagi, Mitsunori Uemura and Atsushi Tackeuchi
The carrier spin relaxation of In0.8Ga0.2As/AlAs/AlAs0.56Sb0.44 coupled double quantum wells is investigated by spin-dependent pump and probe reflectance measurements with a high time resolution of 200 fs. The observed fast spin relaxation time of 9 ps at room temperature indicates high potential for applications to high-speed optical devices. A negative temperature dependence of spin relaxation time is observed between 100 K and room temperature. The spin relaxation is found to be governed by the Bir–Aronov–Pikus process between 10 and 100 K and by the D'yakonov–Perel' and Elliott–Yafet processes between 100 K and room temperature.
04CM06
Makoto Kawano, Shinya Yamada, Soichiro Oki, Kohei Tanikawa, Masanobu Miyao and Kohei Hamaya
We explore epitaxial growth of Co2MnSi films on Si(111) or Ge(111) by means of low-temperature molecular beam epitaxy. We find that as-grown Co2MnSi films consist of mixed phases with L21-ordered structures and microcrystalline ones. As a result, the magnetic moment, which is nearly half of the ideal value, can be obtained even at very low growth temperature. Post-growth annealing was effective to crystallize the microcrystalline phases observed in the as-grown layer, leading to a further enhancement in the magnetic moment. We discuss a difference in growth mechanism between Co2MnSi and other Heusler alloys examined in our previous works.
04CM07
Kosuke Fujiwara, Mikihiko Oogane, Takuo Nishikawa, Hiroshi Naganuma and Yasuo Ando
Arrays of 100×100 magnetic tunnel junctions (MTJs) connected in parallel and series were fabricated. A synthetic antiferro-coupled bottom free layer with a NiFe/Ru/CoFeB structure and MgO tunneling barrier were used to realize a high sensitivity, which is defined as TMR/2Hk, where, TMR is the tunneling magnetoresistance ratio and Hk is the magnetic anisotropy field of the free layer. To obtain a linear response of tunneling resistance against an applied external magnetic field, a double annealing process was carried out. From R–H curve measurements, the sensitivity of the 100×100 integrated MTJs was lower (8%/Oe) than that of a single MTJ (25%/Oe). However, a 1/30 decrease in noise power density was realized in the integrated MTJs. Consequently, a very small magnetic field of 0.29 nT was detected with the integrated MTJs.
04CM08
Sora Ahn, Hyein Lim, Miryeon Kim, Hyungsoon Shin and Seungjun Lee
Spin-torque oscillators (STOs) are new oscillating devices based on spintronics technology with many advantageous features, i.e., nanoscale size, high tunability, and compatibility with standard silicon processing. Recent research has shown that two electrically connected STOs may operate as a single device when specific conditions are met. To overcome the limitation of the small output power of STOs, the phase-locking behavior of multiple STOs is hereby extensively investigated. In this paper, we present a circuit-level model of two coupled STOs considering the interaction between them such that it can represent the phase-locking behavior of multiple STOs. In our model, the characteristics of each STO are defined first as functions of applied DC current and external magnetic field. Then, the phase-locking condition is examined to determine the properties of the two coupled STOs on the basis of a theoretical model. The analytic model of two coupled STOs is written in Verilog-A hardware description language. The behavior of the proposed model is verified by circuit-level simulation using HSPICE with CMOS circuits including a current-mirror circuit and differential amplifiers. Simulation results with various CMOS circuits have confirmed the effectiveness of our model.
Application of nanotubes, nanowires, and graphene
04CN01
Tatsuhiro Numata, Shigeyasu Uno, Yoshinari Kamakura, Nobuya Mori and Kazuo Nakazato
A fully analytic and explicit model of device properties in the ballistic transport in gate-all-around metal–oxide–semiconductor field-effect transistors (MOSFETs) is proposed, which enables circuit simulations. The electrostatic potential distribution in the wire cross section is approximated by a parabolic function. Using the applied potential, the energy levels of electrons are analytically obtained in terms of a single unknown parameter by perturbation theory. Ballistic current is obtained in terms of an unknown parameter using the analytic expression of the electron energy level and the current equation for ballistic transport. We analytically derive the parameter with a one-of-a-kind approximate methodology. With the obtained parameter, the fully analytic and explicit model of device properties such as energy levels, ballistic current, and effective capacitance is derived with satisfactory accuracy compared with the numerical simulation results. Finally, we perform a transient simulation using a circuit simulator, introducing our model to it as a Verilog-A script.
04CN02
Bart Vereecke, Marleen H. van der Veen, Masahito Sugiura, Yusaku Kashiwagi, Xiaoxing Ke, Daire J. Cott, Thomas Hantschel, Cedric Huyghebaert and Zsolt Tökei
We have evaluated the resistance of carbon nanotubes (CNTs) grown at a CMOS-compatible temperature using a realistic integration scheme. The structural analysis of the CNTs by transmission electron microscopy (TEM) showed that the degree of graphitization decreased significantly when the growth temperature was decreased from 540 to 400 °C. The CNTs were integrated to form 150-nm-diameter vertical interconnects between a TiN layer and Cu metal trenches on 200 mm full wafers. Wafers with CNTs grown at low temperature were found to have a lower single-contact resistance than those produced at high temperatures. Thickness measurements showed that the low contact resistance is a result of small contact height. This height dependence is masking the impact of CNT graphitization quality on resistance. When benchmarking our results with data from the literature, a relationship between resistivity and growth temperature cannot be found for CNT-based vertical interconnects.
04CN03
He Cheng, Shigeyasu Uno, Tatsuhiro Numata and Kazuo Nakazato
We propose a compact model of drain current in the ballistic and quasi-ballistic modes for cylindrical gate-all-around (GAA)-MOSFETs with two subbands based on the perturbation theory. By setting one unknown parameter, we can use it to express surface potential and electron confinement energy levels to calculate drain current analytically. With our compact model, we obtained a good agreement with the numerical compact model. In addition, we carry out a NMOS inverter circuit simulation using this model.
04CN04
Junichi Hattori and Shigeyasu Uno
Phonon transport in silicon nanowires (Si NWs) doped with isotopes is investigated theoretically. The ballistic thermal conductance and diffusive thermal conductivity are calculated at room temperature using the phonon dispersion relations derived through a semiempirical atomistic approach. The thermal conductance and conductivity in 28Si NWs randomly doped with 29Si are smaller than those in the corresponding pure 28Si NW, which can be fully explained by the effect of isotope impurities on the dispersion relations. In [001]-oriented 28Si NWs having a square cross section with a side length of 1.086 nm and randomly doped with 29Si, the maximum reduction in thermal conductivity reaches more than 20%. This reduction leads directly to an improvement in the thermoelectric figure of merit by more than 25%. It is also found that the impact of isotope impurities on phonon transport becomes large with increasing mass difference between the constituent and impurity isotopes or with increasing wire cross-sectional area. Phonon transport in isotopic core–shell Si NWs is also investigated. Some of these Si NWs show increased thermal conductance and conductivity although the increase is very small.
04CN05
Aya Shindome, Yu Doioka, Nobuyasu Beppu, Shunri Oda and Ken Uchida
Two-terminal mono- and multilayer graphene nanoribbon resistive random access memories (ReRAMs) are experimentally demonstrated. Fundamental ReRAM properties, device scalability, and width dependence with device scaling are investigated. The lower switching energy is obtained for smaller channel width, indicating the suitability of graphene nanoribbons for high-density LSIs. Operation mechanism is studied by changing the type of contact metal and the number of graphene layers as well as by performing physical analysis by atomic force microscopy (AFM), cross-sectional transmission electron microscopy (TEM), and electron energy-loss spectroscopy (EELS). Then, it is suggested that the mechanism is the chemical bonding-state change of graphene.
04CN06
Atsuko Nagataki, Tatsuya Kagota, Takayuki Arie and Seiji Akita
We have investigated the release of a stuck carbon nanotube cantilever beam by molecular dynamics simulation toward nanorelay applications. We have demonstrated that the successful release of a nanotube arm from the stuck state at room temperature can be realized by the application of a resonant external vibration to the nanotube cantilever beam. The release of the stuck nanotube cantilever beam was well explained by the thermal activation model with a barrier height of the van der Waals interaction between the nanotube arm and the counter electrode.
04CN07
Katsumasa Kamiya and Susumu Okada
We report on total-energy electronic-structure calculations based on the density functional theory performed on linear alkanes [CnH2n+2 with n = 1 to 8] adsorbed on single-walled carbon nanotubes (SWCNTs). We find that all of the alkanes are bound to the SWCNTs. The binding energy of alkane adsorption onto CNT, ΔE(n), is linearly scaled by the length of the alkane chain n: ΔE(n) = -0.048n - 0.038 in units of eV. The electronic structure of alkane–CNT hybrid systems is qualitatively similar to a simple sum of those of an isolated alkane molecule and a pristine CNT. However, detailed analysis of the electronic structure of the hybrid systems reveals that the adsorption of alkane affects the electronic structure of CNTs, depending on the length of the alkane molecule.
04CN08
Takazumi Kawai
Lithium atom intercalation into a graphite layer from the step edge to the interlayer region with various edge terminations of graphite is investigated by first-principles electronic structure calculations. The interactions between the step edge and a Li atom depend on the functional group. There is little interaction of the edge with hydrogen termination, while a large interaction traps diffusing Li atoms for termination by oxidative functional groups. The hydroxylic termination would reduce the initial diffusion barrier for the intercalation. Therefore, the controlled edge termination would successfully enhance the charge and discharge properties of Li ion batteries; on the other hand, the progress of oxidative termination would decrease capacity and charge and discharge rates. The diffusion barrier heights of Li is comparable to or larger than those of other rate-limiting factors during charge and discharge, such as desolvation of Li from electrolyte.
Power devices and materials
04CP01
Satoru Machida, Yusuke Yamashita, Tadashi Misumi and Takahide Sugiyama
In this paper, we report on the effects of trap energy levels on the reverse recovery surge, for the first time. The different current and temperature dependences of the reverse recovery surge with shallow and deep trap energy levels were measured. Results of simulations of current and temperature dependences of the reverse recovery surge with different trap energy levels were similar to measurement results. Through numerical and theoretical analyses based on the Shockley–Read–Hall (SRH) model, it was confirmed that variations in recombination rate due to different trap energy levels affect the current and temperature dependences of the reverse recovery surge. We found that in order to achieve a soft recovery in the design of silicon power diodes, the trap energy levels play a crucial role along with the carrier lifetime profile.
04CP02
Masashi Kato, Masaya Kimura and Masaya Ichimura
To suppress the negative influence of defects on 4H-SiC Schottky barrier diode characteristics, we have developed a new method called passivation of defects by anodic oxidation (PDA). This method utilizes anodic oxidation as a means to form oxide films on defects of the 4H-SiC surface, and these oxide films can function as a resistive layer to the leakage current of Schottky barriers. We observed the current–voltage characteristics of Ni Schottky contacts on 4H-SiC before and after PDA. We found that the leakage current was significantly suppressed after PDA, while the increase in series resistance caused by PDA can be negligible when we apply PDA for an optimum time duration. These results suggest that the PDA method is a promising technique to improve the performance of 4H-SiC Schottky barrier diodes.
04CP03
Kenji Hamada, Naruhisa Miura, Shiro Hino, Tsuyoshi Kawakami, Masayuki Imaizumi, Hiroaki Sumitani and Tatsuo Oomori
We have investigated the effect of n-type doping into the junction field-effect transistor region (JFET doping) on the static characteristics of 3300-V-class 4H-SiC metal–oxide–semiconductor field-effect transistors (MOSFETs). The JFET doping technique is significantly effective in reducing the on-resistance of SiC MOSFETs without degradation of the blocking characteristics when the MOS cells are properly designed. The JFET doping reduces the temperature coefficient of the resistance in the JFET region, leading to lower on-resistance of the SiC MOSFETs at high temperatures.
04CP04
Shiyang Ji, Kazutoshi Kojima, Yuuki Ishida, Sadafumi Yoshida, Hidekazu Tsuchida and Hajime Okumura
Al memory-effect during the growth of p-type 4H-SiC by hot-wall chemical vapor deposition method was investigated. A technique of suppressing the unintentional Al impurities incorporating into succeeding growth was developed by utilizing “site-competition” growth technology. Lowering C/Si ratio from 1 to 0.4 effectively reduced the level of incorporated Al-impurity almost 3 orders, and a high abrupt Al distribution between Al-doped layer and undoped layer was obtained at a reduction factor about 1/17000 with Al-impurity concentration in the undoped layer decreased to the range of 1015 cm-3. In addition, it is found that, due to low C/Si ratio, the nitrogen impurity concentration increases about one order of magnitude up to the order of 1016 cm-3. Combining with site-competition growth technology, the influences of growth temperature and pressure on Al-impurity concentration were examined.
04CP05
Kazuya Konishi, Shuhei Nakata, Yoshiyuki Nakaki, Yukiyasu Nakao, Akemi Nagae, Takanori Tanaka, Yu Nakamura, Yoshihiko Toyoda, Hiroaki Sumitani and Tatsuo Oomori
The relationship between stacking faults and the position of the leakage current inside a triangular defect was analyzed. Triangular defects are categorized into two types on the basis of the current–voltage (I–V) characteristics. It was found that stacking faults (SFs) of the 3C structure inside a triangular defect increase leakage current at a reverse bias voltage as well as forward current at a low bias voltage, while SFs of the SF(4,2) structure inside a triangular defect do not lead to deterioration of device performance in this case.
04CP06
Tomoyuki Shoji, Shuichi Nishida and Kimimori Hamada
Cosmic ray neutrons can trigger catastrophic failures in power devices. It has been reported that parasitic transistor action causes single-event burnout (SEB) in power metal–oxide–semiconductor field-effect transistors (MOSFETs) and insulated gate bipolar transistors (IGBTs). However, power diodes do not have an inherent parasitic transistor. In this paper, we describe the mechanism triggering SEB in power diodes for the first time using transient device simulation. Initially, generated electron–hole pairs created by incident recoil ions generate transient current, which increases the electron density in the vicinity of the n-/n+ boundary. The space charge effect of the carriers leads to an increase in the strength of the electric field at the n-/n+ boundary. Finally, the onset of impact ionization at the n-/n+ boundary can trigger SEB. Furthermore, this failure is closely related to diode secondary breakdown. It was clarified that the impact ionization at the n-/n+ boundary is a key point of the mechanism triggering SEB in power devices.
04CP07
Takao Yamamoto, Masataka Miyake and Mitiko Miura-Mattausch
We have developed a compact model of the injection-enhanced insulated-gate bipolar transistor (IGBT) applicable for circuit optimization. The main development is modeling the hole accumulation in the floating-base region. It is demonstrated that the observed negative gate capacitance is well reproduced with the developed model.
04CP08
Atsushi Uchida, Yuka Morisawa and Satoshi Matsumoto
In this paper, we describe the parasitic bipolar effect of the fabricated thin-film silicon-on-insulator (SOI) power metal–oxide–semiconductor field-effect transistor (MOSFET) at high temperatures. This effect in the on-state was suppressed as temperature increased. This effect in the off-state was promoted as temperature and body contact pitch increased. The parasitic bipolar effect caused by the thermally generated current is enhanced by increasing temperature and decreasing channel length. This reduced breakdown voltage.
04CP09
Masahiro Nagano, Isaho Kamata and Hidekazu Tsuchida
We performed a plan-view and cross-sectional photoluminescence (PL) imaging and a spectral analysis of threading dislocations in 4H-SiC epilayers in the near-infrared region. The bright PL spots of threading screw dislocations (TSDs) and threading edge dislocations (TEDs) observed in the plan-view PL imaging are compared with the grazing incidence synchrotron X-ray topography contrast, and precise discrimination of threading dislocations using the PL technique and the direct acquisition of Burgers vector directions of TEDs are demonstrated. The inclination angles of TSDs and TEDs across a thick epilayer are revealed by the cross-sectional PL imaging, and the variations in the plan-view PL appearances of the threading dislocations are confirmed to originate from the line directions of such dislocations.
04CP10
Atsushi Tanaka, Koji Nakayama, Katsunori Asano, Tetsuya Miyazawa and Hidekazu Tsuchida
The electrical characteristics of 4H-SiC p–i–n diodes with 8H-type in-grown stacking faults are investigated. The 4H-SiC p–i–n diodes have epilayers with a low Z1/2 center density formed by carbon implantation. The forward voltage drops of the 4H-SiC p–i–n diode with 8H-type in-grown stacking faults are larger than those of the 4H-SiC p–i–n diode without an 8H-type in-grown stacking fault. The differential on-resistance of the 4H-SiC p–i–n diode with 8H-type in-grown stacking faults is larger than the drift resistance of the drift layer calculated from the doping density and thickness of the drift layer. A large number of electrons are trapped at 8H-type in-grown stacking faults, and the effective carrier density decreases compared with the doping density.
Photovoltaic materials and devices
04CR01
Satoshi Nakamura, Tsuyoshi Maeda and Takahiro Wada
Cu and In diffusion in Cu-poor CuInSe2 (CIS) with a Cu vacancy have been investigated by first-principles calculations with the generalized gradient approximation. The activation energies and migration pathways are obtained by means of the combination of linear and quadratic synchronous transit (LST/QST) methods and nudged elastic band (NEB) method. The activation energy of Cu migration was 1.06 eV, which is 0.44 eV lower than that of the moving Cu atom located at the center of octahedral site and 0.17 eV lower than that of the moving Cu atom located at center of tetrahedral site. In the transition state, the moving Cu atom is located at the point between the center of the octahedral site and Se atom, which is saddle point of electrostatic potential. The activation energy of In migration (1.70 eV) is much higher than that of Cu migration. The In atom at Cu site (InCu) in Cu-poor CIS is scarcely to occur at room temperature.
04CR02
Shigeru Yamada, Yasuyoshi Kurokawa, Shinsuke Miyajima and Makoto Konagai
We investigate the effects of a niobium-doped titanium dioxide (TiO2:Nb) diffusion barrier layer on the performance of silicon quantum dot superlattice (Si-QDSL) solar cells. The insertion of a 2-nm-thick TiO2:Nb layer significantly reduces phosphorus diffusion from a highly doped n-type layer into a Si-QDSL layer during thermal annealing at 900 °C. The phosphorous concentration in the Si-QDSL layer of the solar cell with the TiO2:Nb diffusion barrier layer was found to be less than 1018 cm-3, which is approximately two orders of magnitude lower than that of the solar cell without the diffusion barrier layer. The reduction in phosphorous concentration leads to the improvement of photo-generated carrier collection in the Si-QDSL layer. The short circuit current density of the solar cell with the diffusion barrier layer was dramatically improved to 1.6 mA/cm2 without the degradation of open circuit voltage and fill factor.
04CR03
Yasuyuki Ota, Tsuyoshi Sueto, Hirokazu Nagai, Kenji Araki and Kensuke Nishioka
Under concentration conditions, it is important to manage the operating temperature of a concentrator photovoltaic (CPV) module, because a high-density solar energy enters into the solar cell. We measured the receiver temperature of the CPV module and evaluated the relationship between the temperature and output of the CPV module. 25 series-connected 820X CPV modules with 2- and 4-mm-thick back chassises were fabricated. In the case of a CPV module with a 4-mm-thick back chassis, the receiver temperature was markedly reduced owing to the effective thermal diffusion of the thicker chassis. The absolute conversion efficiency of the CPV module with the 4-mm-thick back chassis was 1.5% higher than that of the module with the 2-mm-thick back chassis. Moreover, we developed a thermal transfer model of the CPV module and calculated the thermal distribution in the CPV module using a thermal transfer simulator.
04CR04
Tetsuya Kaneko and Michio Kondo
We fabricated crystalline germanium (c-Ge) heterojunction solar cells with a double heterostructure (DH) which consists of hydrogenated amorphous silicon (a-Si:H) layers. In the a-Si:H/c-Ge DH solar cell, the improvement of the conversion efficiency is obtained compared to the c-Ge solar cell having single heterostructure. We investigated effects of post-annealing on characteristics of Ge heterojunction solar cells. The open-circuit voltage (VOC) of Ge heterojunction solar cells increases with increasing post-annealing temperatures above 150 °C. The increase of VOC by post-annealing could be mainly explained by the improvement of passivation quality of a-Si:H for the c-Ge surface. Our results suggest that the a-Si:H double heterostructure is beneficial not only for c-Si-based heterojunction solar cells but also for c-Ge-based heterojunction solar cells.
04CR05
Xiangyu Chen, Dai Taguchi, Keanchuan Lee, Takaaki Manaka and Mitsumasa Iwamoto
Using the Maxwell–Wagner model, we analyzed the interfacial charging of triple-layer organic solar cells (OSCs). Results showed that the charging processes at the two interfaces depend on each other. The electric-field-induced second-harmonic generation (EFISHG) measurements applying external voltage pulses supported the conclusion. On the other hand, the EFISHG measurements using closed circuits with various external resistances clarified the contribution of interfacial charging to the fill-factor of the OSCs. The dielectric nature of the triple layer of the OSCs governs the working mechanism.
04CR06
Kazuya Yokoyama, Toshihiko Kaji and Masahiro Hiramoto
Organic solar cells connecting two photoactive co-deposited layers, i.e., a visible-light-sensitive front layer consisting of metal-free phthalocyanine (H2Pc) and fullerene (C60) and a near-infrared (NIR)-light-sensitive back layer consisting of lead phthalocyanine (PbPc) and C60, were fabricated. The internal quantum efficiency in the visible and NIR regions reached 48 and 43%, respectively. A conversion efficiency of 1.53% was obtained. A model of a function-separated mechanism for the cell, consisting of photocarrier generation by J-PbPc and H2Pc aggregates, hole transport by H-PbPc and H2Pc aggregates, and electron transport by C60, was proposed.
04CR07
Takeo Oku, Junya Nakagawa, Makoto Iwase, Atsushi Kawashima, Kazumi Yoshida, Atsushi Suzuki, Tsuyoshi Akiyama, Katsuhisa Tokumitsu, Masahiro Yamada and Mika Nakamura
Polysilane-based organic solar cells with bulk heterojunction and heterojunction structures were fabricated by spin-coating using a mixture solution. Microstructures of the solar cells were investigated by X-ray diffraction analysis and transmission electron microscopy, which indicated a nanocomposite and amorphous structure. The effects of phosphorus and boron doping into polysilanes were investigated by electrical measurements, Raman scattering analysis and Hall effect measurements. Here, we discuss the photovoltaic properties and microstructures of the solar cells. Energy levels in the present solar cells are also discussed.
04CR08
Takeshi Nomura, Tsuyoshi Maeda and Takahiro Wada
We successfully prepared a Cu2Sn(S1-xSex)3 (CTSSe) solid solution with 0≤x≤1.0. CTSSe solid solution powders were synthesized by mixing the elemental powders and post-annealing at 600 °C. The crystal structure of Cu2SnS3 (CTS) was characterized by Rietveld refinement of the powder X-ray diffraction data and determined to be a monoclinic crystal system. The band gaps of CTSSe solid solution were determined by the diffuse reflectance spectra of the powder samples and the transmittance spectrum of the film fabricated by a non-vacuum thin-film fabrication process called printing and high-pressure sintering (PHS). The band gap (Eg) of CTS is 0.87 eV, which is in good agreement with the recently reported value of monoclinic CTS film. The band gap of the Cu2Sn(S1-xSex)3 solid solution linearly decreases from 0.87 eV (x = 0.0) to 0.67 eV (x = 0.6) with increasing Se content. The CTSSe solid solution has potential as a narrow band-gap absorber material for thin-film full spectrum solar cells.
04CR09
Hiroki Hashiguchi, Tomihisa Tachibana, Mari Aoki, Takuto Kojima, Yoshio Ohshita and Atsushi Ogura
For realizing low-cost and high-conversion-efficiency silicon solar cells, we propose an ion shower doping technique for fabricating conventional and selective emitter structure solar cells. Because of its high through put with a large beam area, the technique could lead to low-cost production of the emitter layer. We used this technique to form a uniform emitter layer and also a selective high-doping emitter region for silicon solar cells, which were compared with cells prepared by POCl3 diffusion. The conventional structure cells were confirmed to have good electrical properties with uniform conversion efficiency compared with the cells prepared by POCl3 diffusion. There was no doping-induced damage nor metal impurities interfused during the ion shower doping. In addition, the conversion efficiency of selective emitter structure cells was higher than that of cell prepared by POCl3 diffusion only. We concluded that the ion shower doping technique is useful for forming a uniform emitter layer as well as a selective emitter region.
04CR10
Gerry Lucovsky, Greg Parsons, Daniel Zeller and Jinwoo Kim
This article addresses low defect densities in hydrogenated amorphous silicon, a-Si1-x:Hx with approximately 10 at. % bonded H, x∼0.1. Based low defect densities at mid-gap, ∼0.5 to 1×1016 cm-3, a-Si:H thin films have been integrated into photovoltaic (PV) devices and thin film transistors (TFT's). Amorphous Si (a-Si) thin films with no detectable bonded-H have been used as precursors for polycrystalline gate electrodes in microelectronic applications. PV and TFT alloys have been deposited by glow discharge (GD), remote plasma-enhanced chemical vapor deposition (RPECVD), and reactive magnetron sputtering (RMS) with different bonded-H content determined by deposition precursors and substrate temperatures. Two conditions are required for the lowest Si dangling bond densities: (i) a monohydride, Si–H, concentration of ∼10 at. % H, and (ii) deposition, and/or a post-deposition annealing at 240 to 300 °C.
04CR11
Keisuke Ohdaira
High-pressure water-vapor annealing (HPWVA) is performed on 3-µm-thick polycrystalline silicon (poly-Si) films formed on glass substrates by crystallizing electron-beam (EB)-evaporated precursor amorphous Si (a-Si) films by flash lamp annealing (FLA). HPWVA at higher temperature and pressure tends to result in a lower defect density of FLC poly-Si films. The defect density of FLC poly-Si films can be reduced from ∼3×1017 to ∼2×1016/cm3 when the HPWVA temperature is 500 °C and the pressure is more than 8 MPa, which is sufficiently of device grade. The annealing of flash-lamp-crystallized (FLC) poly-Si films under inert-gas atmosphere does not lead to sufficient reduction in their defect density, indicating the necessity of water vapor during annealing.
04CR12
Yusuke Shinmura, Masayuki Kubo, Toshihiko Kaji and Masahiro Hiramoto
Thick heterojunction cells composed of fullerene and p-type hole-transporting materials (HTMs) doped with molybdenum oxide (MoO3) were fabricated. The Fermi level (EF) of HTMs shifted toward the positive direction and close to the upper edge of the valence band following MoO3 doping. These EF shifts indicate that intrinsic HTMs changed to be of the p-type. The introduction of p-type HTMs to the cells increased photocurrent density and fill factor. The increase in photocurrent density can be explained by the formation of built-in potential at the interface between p-type HTMs and C60. On the other hand, the increase in fill factor can be explained by the drastic decrease in the resistance of 300-nm-thick HTM films, which reached a very small value of 2 Ω.
04CR13
Taisuke Matsumoto, Takeo Oku and Tsuyoshi Akiyama
A series of bulk-heterojunction organic solar cells incorporating silver nanoparticles was fabricated and evaluated. Silver nanoparticles were incorporated in the hole-transport layer of the solar cells. Plasmonic absorption and the generation of localized surface plasmon resonance of silver nanoparticles were confirmed by absorption and surface enhanced Raman scattering spectra even in the hole-transport material. The incorporation of silver nanoparticles increased photoelectric conversion efficiencies, whose enhancement properties were varied by the incorporation amount of silver nanoparticles.
04S001
The following article is Free article
04S002
The following article is Free article
Yukiharu Uraoka, Seiji Akita and Kouichi Ono