Organic Materials and Characterization
405
Hiroshi Nanjo, Toshiro Yokoyama, Ryuzi Katoh, Masateru Nishioka, Yaeko Sasaki, Masayuki Nakamura and Tsukasa Ono
A fluorescent thin film was fabricated by the electrochemical polymerization of pyrene triazine thiol (PMN) molecules on type 304 stainless steel. The features of the film were characterized by spectroscopic ellipsometry, atomic force microscopy, X-ray photoelectron spectroscopy, and fluorescence spectroscopy. The thin film was formed not of a fiber network but of nanoparticles approximately 30 nm in diameter after 90 min of polymerization. The film thickness increased rapidly to 25 nm after 3 min and then gradually increased to 31–37 nm after 90 min. A rough substrate surface resulted in a rough and thick PMN film. The most stable structure was simulated by molecular mechanics (MM2) calculations, and the tetramer of a PMN derivative had an easily formed particle-like structure. The fluorescence intensity of the PMN film can be used to rapidly measure oxygen content with some film degradation.
411
Takahiro Aida, Tetsuya Yamamoto, Wei Ou-Yang, Takaaki Manaka and Mitsumasa Iwamoto
Experiments were conducted on Langmuir monolayers composed of chiral dipalmitoyl-phosphatidylcholine (D-DPPC and L-DPPC) molecules and racemic DPPC (dl-DPPC) molecules by Maxwell displacement current (MDC) measurement and Brewster angle microscopy (BAM) to examine the orientational structure and domain shapes of monolayers. The MDCs generated from chiral DPPC monolayers during monolayer compression resembled each other, indicating that the molecular chirality does not have a direct effect on the generation of MDC. The domain shapes of chiral DPPC monolayers depended on the molecular chirality. On the other hand, the MDC generated from racemic DPPC monolayers was different from that generated from chiral DPPC monolayers at the beginning of the pressure plateau, suggesting an effect of molecular chirality. Interestingly, a spanner-like domain shape of racemic DPPC monolayers was discovered. We suggest that phase separation within the domain by monolayer compression is responsible for the formation of this domain shape.
416
Nobutaka Tanigaki, Claire Heck, Toshiko Mizokuro, Hideyuki Minato, Masahiro Misaki, Yuji Yoshida and Reiko Azumi
Polyfluorene oriented films produced by a friction-transfer method show polarized blue-light emission. A subsequent doping of some types of fluorescent dyes into the oriented films using a vapor transportation method resulted in polarized emission from the oriented polymer and from the doped dye. Polarized photoluminescence spectra from the polyfluorene films doped with oligothiophenes, quaterthiophene, and sexithiophene showed that these materials exhibit marked dichroism caused by the alignment of the oligothiophene molecules parallel to the polymer chain. We succeeded in extending the wavelength range of the polarized emission by doping fluorescent dye into the films.
420
Hiroshi Kawabata, Ken Tokunaga, Shigekazu Ohmori, Kazumi Matsushige and Hiroto Tachikawa
Hybrid density functional theory (DFT) calculations have been carried out for neutral and radical cation species of a fused thiophene oligomer, denoted by T(n), where n represents the number of thiophene rings in the oligomer, to elucidate the electronic structures at ground and low-lying excited states. A polymer of fused thiophene was also investigated using one-dimensional periodic boundary conditions (PBCs) for comparison. It was found that the reorganization energy of a radical cation of T(n) from a vertical hole trapping point to its relaxed structure is significantly small. Also, the reorganization energy decreased gradually with increasing n, indicating that T(n) has an effective hole transport property. It was found that the radical cation species of T(n) has a low energy band in the near-IR region, which is strongly correlated to hole conductivity. The relationship between the electronic states and hole conductivity was discussed on the basis of theoretical calculations.
425
Xiaoliang Mo, Toshiko Mizokuro, Nobutaka Tanigaki, Takashi Hiraga, Noboru Umehara, Kazuyoshi Takagi and Sumio Yamamoto
We report the investigation of a spray beam and the initial stage of thin-film preparation in a vacuum spray method. As the key parts, two types of orifice plate with pinholes with diameters of 10 and 20 µm were used in the spray nozzle. The spray solution beam in a vacuum chamber was irradiated with a green laser. By measuring the length of the laser-scattered part, the divergence angle of the spray beam and the relationship between the beam width and spray pressure were investigated. After diluted poly[2-methoxy-5-(2'-ethylhexoxy)-1,4-phenylenevinylene] (MEH-PPV) in a chloroform solution was injected onto the heated substrates in a short time period, the MEH-PPV particles on the substrates were analyzed by optical microscopy and atomic force microscopy (AFM). Compared with the orifice plate with a pinhole with a diameter of 20 µm, the 10-µm-orifice plate generated a spray beam with a big divergence angle, and the MEH-PPV particles on the substrate were smaller and more uniform in size.
432
Satoko Nishiyama, Masahiro Tajima, Yoshikata Nakajima, Tatsuro Hanajiri and Yasuhiko Yoshida
The N 1s core binding energies of spin-coated poly(vinylpyridine) (PVPy), quaternized PVPy, and UV-irradiated PVPy were determined using X-ray photoelectron spectroscopy, and the depth profiles were determined using Ar+ beam etching. In typical N 1s spectra, cationic nitrogen atoms appeared at a binding energy 2–3 eV higher than that of neutral pyridine (Py). Changes in alkylpyridiniums in N 1s and bromide in Br 3p were determined according to etching cycles. In our PVPy cases, two types of nitrogen appeared at a region of high energy compared with that of neutral Py, and the differences in the binding energies between those states and neutral Py were all less than 2 eV. These nitrogens can be assigned to hydrogen-bonded Py and a complex formed among Py rings. Neutral Py, the complex Py, and hydrogen-bonded Py are very close together, and they were located at 399.0, 399.7, and 400.6 eV, respectively. Traces of ionic species were observed only in IR spectra.
438
Yuuki Tidiishi, Shigeki Naka and Hiroyuki Okada
An organic semiconductor superlattice using pentacene as a semiconductor has been investigated. In general, stacked pentacene shows a dendritic structure. However, in a thin pentacene layer as two monolayers, the roughness of the pentacene surface is smooth. Therefore, a smoother surface will be obtained by stacking a thin pentacene/insulator structure. From this, an insulating material of alumina is selected and the multilayer of pentacene [2 monolayer (ML)]/insulator is investigated. As a result, a relatively smoother surface roughness of 2.0 nm was observed for the structure of [pentacene (2 ML)/Al2O3 (5 Å)] × 13/pentacene (2 ML). On the other hand, in the case of the silicon dioxide layer, a nonuniform layer with a smaller grain was observed. This stacked organic layer structure will be useful for a multichannel organic layer for application in organic field-effect transistors.
Electrical and Optical Propteties of Organic Materials
441
Tomoyuki Sasaki, Hiroshi Ono and Nobuhiro Kawatsuki
We investigated the diffraction properties of slanted anisotropic gratings originating from a photoinduced molecular reorientation of polymer-dissolved liquid crystal composites doped with trace amounts of an azo-dye. The diffraction efficiencies of the holographic gratings were strongly dependent on the incident angle and polarization state of the probe beam. In order to explain the properties, a model of the periodical reorientation distribution is presented, considering the relationship between the polarization state of the pump beam and the molecular reorientation of the material. The optical properties of the structures were simulated by employing the finite-difference time-domain (FDTD) method. The simulation results showed good agreement with the observed diffraction properties.
446
Shizuyasu Ochiai, Koji Isogai, Kenzo Kojima, Asao Ohashi and Teruyoshi Mizutani
Owing to advancing large-scale optical communications technology, all-optical devices have attracted attention in high-speed data communication systems. We measured the characteristics of the optical bistability of elements fabricated using a terthiophene/poly(methyl methacrylate) (PMMA) composite film and a prism, and investigated the origin of the optical bistability. The measured optical bistabilities revealed excellent hysteresis characteristics. The shift of the on-off position of the optical bistability decreased with the composite film with a large third-order nonlinear optical susceptibility.
450
Kunjithapatham Sethuraman, Shizuyasu Ochiai, Yuu Yamada, Suguru Mototani, Kenzo Kojima, Asao Ohashi and Teruyoshi Mizutani
In this paper, we report on the third-order nonlinear optical properties of poly(3-hexylthiophene) (P3HT) thin films prepared using solution methods. The third-order optical susceptibilities χ(3)(-3ω;ω,ω,ω) of P3HT thin films spin-coated and drop-cast on quartz glass substrates were estimated from optical third harmonics measured using the Maker-fringe method. The orientation, alignment, and crystallinity of the P3HT thin films obtained were evaluated using atomic force microscopy (AFM), X-ray diffraction (XRD) analysis, and UV–visible absorption spectra. The maximum nonlinear optical susceptibility χ(3) (NLOS), as estimated from the drop-cast film, was 1.55×10-8 esu, which was higher than that of a spin-coated film by one order. The enhancement of χ(3) is associated with the orientation and crystallinity of the P3HT molecule on the substrate.
Organic Devices
455
Tatsuo Mori, Shunsuke Nishino, Takao Nishikawa and Satoshi Ogawa
We investigate the effect of a self-assembled monolayer (SAM) as a hole injection layer on the electroluminescence (EL) properties of organic light-emitting diodes (OLEDs). We modify the surface of an indium–tin-oxide (ITO) substrate using (heptadecafluoro-1,1,2,2-tetrahydrodecyl)triethoxysilane (F-SAM) and n-decyltriethoxysilane (CH3-SAM). The current of the OLED with F-SAM is higher that those of the OLEDs with or without CH3-SAM at the same voltage and the same as that of an OLED with copper phthalocyanine (CuPc). In addition, the half-lifetime of the OLED with F-SAM is 2500 times greater than that of the OLED without the hole injection layer and about twice that of the OLED with CuPc. We discuss the conduction mechanism of the OLED in terms of the barrier height of the hole injection and the voltage distribution of the organic layers.
460
Hirotake Kajii, Yutaka Ohmori, Hideki Maki, Yasuhiro Sekimoto, Yasuhiro Shigeno, Naoya Takehara and Hiroshi Nakagawa
The fabrication and characteristics of organic light-emitting diodes (OLEDs) with highly conductive polymer electrodes as an anode and the stress tolerance of the devices fabricated on polymeric substrates were studied. By inserting a wet-processed organic layer between a polymer electrode and a dry-processed hole-transport layer, the surface emission pattern from an OLED was markedly improved. For the device with a wet-processed organic layer (methoxy-substituted 1,3,5-tris[4-(diphenylamino)phenyl]benzene), the uniform surface emission resulted from the uniform applied electric field in the emissive layer and the improvement in interface adherence. The OLED with a wet-processed layer as a hole injection layer showed a maximum luminance and a maximum efficiency of 10,000 cd/m2 and 3.5 cd/A, respectively. For the device fabricated on a polymeric substrate, the impact testing of the OLEDs with highly conductive polymer electrodes [poly(ethylenedioxythiophene):poly(styrene sulfonic acid)] as an anode revealed that the emission lasted for more than several ten thousand steps. A highly conductive polymer electrode had a sufficient tolerance to mechanical stress, as determined by comparing devices with indium tin oxide and a highly conductive polymer as anodes.
464
Yoshitaka Nakano, Koji Noda, Hisayoshi Fujikawa and Takeshi Morikawa
We have investigated emissive interface states in fabricated indium–tin-oxide (ITO)/N,N'-di-1-naphthyl-N,N'-diphenyl-1,1'-biphenyl-4,4'diamine (α-NPD)/tris(8-hydroxyquinoline) aluminum (Alq3)/LiF/Al organic light-emitting diodes (OLEDs) by modified deep-level optical spectroscopy (DLOS). DLOS after hole injection into the OLEDs revealed a discrete trap level located at ∼1.77 eV below the conduction band of Alq3 in the emissive interface region, in addition to the band-to-band transitions of charge carriers from α-NPD to Alq3. This pronounced level can be activated as an efficient recombination center of the charge carriers. Also, this trap level was extensively distributed to a lower energy with increasing hole injection rate. Therefore, this level is probably attributable to intrinsic trap states at the α-NPD/Alq3 emissive interface. Thus, DLOS has been proven to be a powerful tool for the characterization of emissive interface states in the OLEDs.
468
Young Ran Park, Eunkyoung Nam and Young Sung Kim
We have investigated transparent conducting properties of using In-doped (4 at. %) zinc oxide (IZO) thin films deposited on glass substrate by pulsed DC magnetron sputtering at low processing substrate temperatures. As increase of the substrate temperature, IZO thin films with better c-axis orientations were grown in perpendicular to the substrate and work functions of IZO films slightly decrease. The optical properties showed high transmittance of higher than 85% in the UV–visible region and exhibited the absorption edge of about 350 nm. The electrical properties exhibited the low resistivity of 1.1 ×10-3 Ω cm and the high mobility of ∼7.8 cm2 V-1 s-1. The organic light emitting diodes (OLEDs) with an IZO anode achieved a maximum luminance efficiency of 2.7 cd/A and external quantum efficiency of 0.47%, which are compared to the values of a control device fabricated on commercial ITO anode. These results indicate that IZO films hold promise for anodic electrodes in the OLEDs application.
472
Masahiko Ohmori, Seiko Ueno, Naomi Kurachi, Momoe Sawamura, Masaaki Hattori, Toyokazu Inoue, Takeshi Miyabayashi, Yuuzou Takao, Shingo Hibino, Ichiro Tsuchiya et al
A light-emitting seal using a self-aligned organic light-emitting diode (OLED) and a laminate process is proposed and demonstrated. This device has a self-aligned ink-jet-printed structure where an insulating material is dissolved in a solvent, and a mixture of organic materials is formed at the same position as that of the ink-jet-printed region. A cathode electrode is laminated onto the above ink-jet-printed structure. The merits of the device are its simple fabrication without the need for photolithography or any vacuum process, and its lower cost. The typical luminance obtained was 6,810 cd/m2. The concept of the device is useful for light-emitting seals (LES), tags and graphics with noncontact electromagnetic electric supply but no electric supply line.
476
Ryousuke Tamura, Shuhei Yoshita, Eunju Lim, Takaaki Manaka and Mitsumasa Iwamoto
The behavior of charges in pentacene field-effect transistors (FETs) with a ferroelectric gate insulator [copolymer of vinylidene fluoride and tetrafluoroethylene, i.e., P(VDF-TeFE)] was investigated. Two peaks appeared in the Igs–Vgs characteristics at Vds = 0 V. Analyzing the behavior of the charges in the pentacene FETs revealed that the first peak appearing at the lower Vgs is ascribed to the exhaustion of accumulated holes at the pentacene/P(VDF-TeFE) interface in the direction from the interface to the source and drain electrodes in response to the electric field formed in pentacene. On the other hand, the second peak appearing at the higher Vgs is ascribed to the turn-over of the spontaneous polarization of the P(VDF-TeFE). However, a threshold voltage shift due to the spontaneous polarization that was small compared with the expected shift suggests that the turn-over of the spontaneous polarization is partial. A mechanism of the turn-over of spontaneous polarization is analyzed in terms of the Maxwell–Wagner effect.
480
Eiji Itoh, Yusuke Higashimoto and Keiichi Miyairi
Fullurence (C60)-based n-channel field effect transistors (FETs) have been fabricated on polyimide gate insulators as an alternative to conventional oxide gate insulators. The field effect mobility µe of C60 FET was improved to higher than 0.1 cm2 V-1 s-1 by heat treatment at 160 °C. This improvement was attributed to the de-doping of oxygen molecules, which were adsorbed by short-term exposure to air during sample transfer. The C60 films deposited on polyimide become amorphous even after the heat treatment or heating the sample during deposition. On the other hand, the crystalline phase of C60 appears when the films were deposited on pentacene-coated polyimide. Both the field effect mobility and the conductance of bulk C60 were increased markedly by the insertion of an ultrathin pentance layer between C60 and the polyimide gate insulator.
484
Kazunari Shinbo, Toshiyuki Akazawa, Yasuhito Takatsuka, Yasuo Ohdaira, Akira Baba, Keizo Kato and Futao Kaneko
Vapor treatments using several organic solvents were carried out for vacuum-evaporated magnesium phthalocyanine (MgPc) thin films. The UV–vis absorption spectra, surface morphologies, and X-ray diffraction patterns were markedly altered by the treatments and depend on the vapor. Furthermore, Au top-contact organic field-effect transistors (OFETs) were fabricated using MgPc films with and without the vapor treatments. The FET with N-methylpyrrolidone treatment did not work, but that with dichloromethane vapor treatment showed a large improvement in the on/off ratio and field-effect mobilities. Ethanol vapor treatment (5 min) also improved the FET characteristics, but long-term treatment (60 min) induced poor performance.
488
Iain McCulloch, Michael Coelle, Kristijonas Genevicius, Rick Hamilton, Michael Heckmeier, Martin Heeney, Theo Kreouzis, Maxim Shkunov and Weimin Zhang
Fabrication of display products by low cost printing technologies such as ink jet, gravure offset lithography and flexography requires solution processable semiconductors for the backplane electronics. The products will typically be of lower performance than polysilicon transistors, but comparable to amorphous silicon. A range of prototypes are under development, including rollable electrophoretic displays, active matrix liquid crystal displays (AMLCD's), and flexible organic light-emitting diode (OLED) displays. Organic semiconductors that offer both electrical performance and stability with respect to storage and operation under ambient conditions are required. This work describes the initial evaluation of reactive mesogen semiconductors, which can polymerise within mesophase temperatures, “freezing in” the order in crosslinked domains. These crosslinked domains offer mechanical stability and are inert to solvent exposure in further processing steps. Reactive mesogens containing conjugated aromatic cores, designed to facilitate charge transport and provide good oxidative stability, were prepared and their liquid crystalline properties evaluated. Both time-of-flight and field effect transistor devices were prepared and their electrical characterisation reported.
492
Keisuke Sugiyama, Shota Iizuka, Hisashi Yashiro, Hisashi Fukuda and Yuhei Shimoyama
X-ray diffraction (XRD) data shows lattice planes with a spacing of 12.8 Å for copper phthalocyanine (CuPc) thin films. Comparison between the XRD patterns of CuPc powder and thin films suggests that the molecules are oriented along the (100) lattice plane nearly perpendicular to the substrate. The XRD data of the perfluorinated phthalocyanine (F16CuPc) thin film indicate a similar structure to that of CuPc, but with a wider lattice spacing of 14.6 Å. Angular variations of the line position (g-value) of ESR spectra reveal tilt angles of 39 and 34° for the CuPc and F16CuPc thin films, respectively, and the same deviation angle of 24°. This indicates a cone-shaped orientation of CuPc and F16CuPc with similar tilt and deviation angles. The ESR linewidths of both films show angular variation, indicating one-dimensional spin-chain interactions in both the CuPc and F16CuPc thin films. Organic thin-film transistors (OTFTs) with CuPc and F16CuPc films are tested for their suitability as channel layers. The OTFTs with a CuPc film exhibit conduction with holes as carriers, and have a field-effect mobility of 2.6 ×10-5 cm2 V-1 s-1 and an on/off ratio of 10 in the accumulation mode. The OTFTs with F16CuPc films exhibit conduction with electrons as carriers (n-type), and have a field-effect mobility of 2.0 ×10-4 cm2 V-1 s-1 and an on/off ratio of 2.4 ×104 in the accumulation mode.
496
Suguru Mototani, Shizuyasu Ochiai, Xin Wang, Kenzo Kojima, Asao Ohashi and Teruyoshi Mizutani
The relationship between the carrier mobility and the structure/morphology of polymer semiconductor molecules on a substrate remains a very important issue in organic electronics. In this paper, the relationship between the crystallinity of drop-cast regioregular poly(3-hexylthiophene-2,5-diyl) (RR-P3HT) thin films and polymer substrates was discussed by using heat-crosslinkable poly(4-vinylphenol) (PVP) as the gate insulator in organic field-effect transistors (OFETs). The effect of a self-assembled monolayer (SAM) of 1,1,1,3,3,3-hexamethyldisilazane (HMDS) on crosslinked PVP was also examined and the performance of the OFET was investigated. Results show that not only the orientation and crystallinity of the polymer semiconductor are very important in determining the OFET performance, but also the gate dielectric properties, surface roughness, and the interface properties between the gate and semiconductor layers are important factors.
501
Ken-ichi Ogawa, Nobuyuki Aoki, Kun'ichi Miyazawa, Shigeo Nakamura, Tadahiko Mashino, Jonathan P. Bird and Yuichi Ochiai
Various kinds of field-effect transistor (FET) have been fabricated with C60 nanowhisker (NW) and also studied for nano-electronics application. Especially, pure and solvated C60 NWs have been synthesized in N2 environment so as to clarify the best device performance of C60 NW-FET. The FET works not only under vacuum but also in N2 environment when kept in the solvated condition. The solvated C60 NW-FET shows a clear improvement of their on/off ratio in the solvated condition, and the highest electron mobility after annealing. Although further study is needed, our results demonstrate the possibility, by appropriate choice of the solvent, of achieving good improvements in FET performance. Moreover, new kinds of C60 NW, such as derivative-based and nanotube-type one, have also been studied with regards to their fundamental FET characteristics.
505
Yuusuke Noma, Takashi Kado, Daisuke Ogata, Yoshitaka Hara and Shuzi Hayase
The effect of surface state (trap) passivation of a nanoporous TiO2 electrode was examined by a thermally stimulated current method (TSC). TSC decreased after dye molecules were adsorbed or after Al2O3 thin layers were fabricated on the TiO2 electrode, suggesting that the surface trap of the TiO2 electrode was actually passivated following these surface modifications. Electron diffusion coefficient in the TiO2 electrode increased and electron recombination was retarded after the TSC peak decreased by the passivation. All-solid-type organic solar cells consisting of nanoporous TiO2/Al2O3/dye/polythiophene derivative (Cell 1) were prepared and the photovoltaic properties of Cell 1 were compared with those of Cell 2 consisting of TiO2/dye/polythiophene derivatives. By inserting the Al2O3 layer between the TiO2 layer and the dye molecule layer, we observed improvement of the photovoltaic properties.
509
Eiji Itoh, Yuta Takamizawa and Keiichi Miyairi
We have prepared a photovoltaic device consisting of poly[2-methoxy,5-(2'-ethyl-hexyloxy)-p-phenylenevinylene] (MEHPPV) and an n-type crystalline TiO2 (anatase) thin film by high-temperature process and low-temperature process at a temperature lower than 150 °C by sol–gel techniques. The refluxed sol of titanium-tetraisopropoxide (TTI) with water and nitric acid formed anatase phase TiO2 without requiring the high-temperature process, and the wettability of sol is successfully improved by diluting sol with ethanol. The short circuit current JSC, fill factor, and the power conversion efficiency increase with the heat-treatment temperature of TiO2, which is attributed to the improvement of series resistance of the TiO2 film. On the other hand, the open circuit voltage remains almost constant (ca. 1.0 V) with the change in heat-treatment temperature between 60 and 120 °C, whereas it decreases to 0.76 V in the device prepared on the TiO2 film sintered at 500 °C, probably owing to the change in crystallinity. The origin of open circuit voltage in indium tin oxide (ITO)/TiO2/MEHPPV/Au is also discussed. The open circuit voltage corresponds well to the energy difference of the conduction band edge of TiO2 and the highest occupied molecular orbital (HOMO) of MEHPPV (ca. 1 eV) in the device consisting of the ITO/low-temperature TiO2/MEHPPV/Au system.
513
Yuzuru Hijikata, Junichi Inoue and Masafumi Yamashita
The performance of organic photovoltaic cells containing tin–phthalocyanine (SnPc) as a donor layer and fullerene (C70) as an acceptor layer is studied using multi layer structures incorporating two hetero junctions with an ultra thin layer of Ag as an internal electrode. The photovoltaic conversion efficiency of the indium–tin oxide (ITO)/poly(3,4-ethylene dioxythiophene):poly(styrene sulfuric acid) (PEDOT:PSS)/SnPc/SnPc:C70/C70/Ag/SnPc/SnPc:C70/C70/Ag cell is improved from 1.54 to 1.90% by heating the substrate at 100 °C during film evaporation. X-ray diffraction measurements indicate that the ordering of phthalocyanine molecules is improved from the α phase to the β phase by heating the substrate.
516
Young Ran Park, Donggeun Jung and Young Sung Kim
Hydrogenated In-doped ZnO (IZO:H) anodic films grown at different ratios (R) of hydrogen to argon were deposited at a low processing temperature of 100 °C on a glass substrate by pulsed DC magnetron sputtering for photovoltaic cells. Even at a low substrate temperature, the transparent electrode showed an average optical transmittance of 88% in the visible range and a reduced resistivity of less than 3.5×10-3 Ω·cm. The organic photovoltaic cells with an IZO:H (R=0.08) electrode achieved a maximum power conversion efficiency (η) of 0.53%, which is as good as the values of the control device fabricated on a commercial ITO electrode (η=0.48%). This indicates that the efficiency of the organic photovoltaic cells is critically affected by the injection of hydrogen gas during the deposition of IZO:H. The high quality IZO:H film developed herein is promising as an alternative to conventional ITO film.
Organic-Inorganic Hybrid System
521
Tetsushi Okamoto and Shuhei Nakamura
In this paper we present the heat-resisting properties of a hybrid made from poly(dimethylsiloxane) (PDMS) and tetraethoxysilane (TEOS) through a sol–gel reaction. It is found that the hybrid with ratio TEOS/PDMS = 10 shows a weight loss of less than 3% after aging treatment at 200 °C for 480 h in air. The reason for the good thermal endurance property is that low-molecular-weight PDMS chains bond to the surfaces of silica derived from TEOS, leading to the suppression of the thermal decomposition of the chains. After the aging treatment, the mechanical properties of the elastic modulus and breaking stress are improved and elongation at breaking decreases. It is also found that the electrical insulating properties are stable upon aging treatment.
527
Katsuhiko Suzuki, Takashi Hiratsuka, Soutaroh Katoh and Yuta Hirano
Various composite devices consisting of nano- and/or microparticles and epoxy resin have been fabricated without heat treatment using a coagulant. The composite including the nanoparticles and the resin showed a rather considerable negative longitudinal magnetoresistance of about -5% compared with the composite including the microparticles. The average tunnel barrier thickness among particles of the composite containing the microparticles was about 2.7 times larger than that of the composite containing the nanoparticles. In both composites containing the micro- and nanoparticles, it was found that the slope of the pressure dependence of the resistance changed suddenly near 20 and 5 MPa in the compression and decompression processes, respectively. This shows that a change in the transport mechanism occurred owing to the pressure. The effects of the dispersion of nano- and/or microparticles and resin in the composite on the transport properties are also discussed.
531
Nimai Chand Pramanik and Sang Il Seok
The preparation of ceramic/polymer composites (BaTiO3–polymer in particular) has received much current interest for various electronic applications, because of the possibility of combining the effect of the processability of the organic components with that of the desired electrical properties of the ceramics. The synthesis of polyimide-based inorganic–organic hybrid thin films containing crystalline BaTiO3 nanoparticles and their dielectric properties are discussed. The precursor for the polyimide was prepared from benzophenone-3,3',4,4'-tetracarboxylic dianhydride (BTDA) and 4,4'-diamino-3,3'-dimethyl diphenyl methane (DADMDPM) and used as an organic matrix for a ceramic/polymer hybrid and that of the crystalline BaTiO3 nanoparticles was prepared by the wet-chemical decomposition of the [Ti(acac)3]+ complex with Ba(OH)2. The BaTiO3, prepared by the decomposition of the Ti-acac complex showed good crystallinity (average particle size = 90 nm) with better dispersibility in an organic medium (NMP). Crack-free thin films of 3.5–4.5 µm thickness were obtained by a single spin coating operation after curing the air-dried films at 150 °C. The polyimide/BaTiO3 hybrids exhibited a wide range of relative permittivity values (ε= 3.81–31.57) at room temperature.
538
Moonkyong Na, Hoyyul Park, Dongpil Kang, Myeongsang Ahn and Heewoong Lee
Organic–inorganic hybrid sols were synthesized using colloidal silica and organoalkoxysilane using the sol–gel process. Hybrid sols were functionalized using methyltrimethoxysilane (MTMS) and γ-glycidoxypropyltrimethoxysilane (GTMS). Coating films were formed on a glass substrate using a spin coating procedure. The hybrid sols were evaluated for stability and thermal degradation. Viscosity increased markedly when the hybrid sols were reacted for 10 d. It was found that the hybrid sols reacted over 10 d were difficult to be used as coating agents. The thermal degradation of a colloidal silica (CS)/MTMS sample occurred at 650 °C owing to the decomposition of a methyl group. Two CS/MTMS/GTMS samples degraded at 400 °C owing to the decomposition of an epoxy group. Coating films were characterized in terms of hydrophobicity, surface morphology, and electrical resistance. CS/MTMS coating films showed a high contact angle, indicating hydrophobic character. The contact angle of the CS/MTMS/GTMS coating film decreased owing to epoxy group when a large amount of GTMS was added. The roughness of all coating films was less than 20 nm. The surface resistance of the coating films reacted for 7 d was measured. The surface resistance of the coating films was more than 1013 Ω.
Inorganic Materials and Characterization
541
Myo Than Htay, Minoru Itoh, Yoshio Hashimoto and Kentaro Ito
Spectral features of the near-band-edge photoluminescence (PL) of submicron-sized ZnO crystals such as nanoplatelets, nanowires, and nanorods grown by an ultrasonic spray pyrolysis (USP) technique were investigated. The measurements of time-integrated and time-resolved PL spectra were performed in the temperature range of 8–300 K under various excitation densities by using the fourth harmonics (4.66 eV) of a Nd:YAG laser. Exciton-related emission bands were clearly observed in the ZnO crystals having different morphologies. In nanoplatelets, an emission band originating from radiative recombination of donor–acceptor pairs was also found at around 3.17 eV, indicating the existence of acceptor centers. The binding energies of donor and acceptor were about 53 and 200 meV, respectively. In nanowires, the intensity of an emission band peaking at 3.32 eV obeyed a quadratic dependency on the density of excitation. This fact shows that an inelastic exciton–exciton scattering process is efficient in the nanowires because of high crystal quality.
546
Takeshi Asada, Kenjirou Nagase, Nobuyuki Iwata and Hiroshi Yamamoto
Representative magnetoelectric (ME) material Cr2O3 films were prepared on R-cut sapphire (R-Al2O3) and SrTiO3 (STO) substrates with the aim of applying them in perovskite oxide electronic devices. Cr2O3 thin films were deposited using the DC–RF hybrid magnetron sputtering system at different substrate temperatures. When the R-Al2O3 substrate temperature was 550 °C, Bragg peaks (n,n,0,2n) were observed. The full width at half maximum (FWHM) of the rocking curve was smallest at Ts = 550 °C with a value of 0.52°. The grain size of Cr2O3 increased with substrate temperature in the 400–600 °C range. The lengths of rectangular Cr2O3 grains were in the ranges of 200–600 nm along the [1101] direction and 100–300 nm along the [1120] direction. Furthermore, Cr2O3 films were deposited on SrTiO3 (100) with CeO2 buffer layers. The Cr2O3 thin film deposited on the smooth CeO2 buffer layers with the average roughness (Ra) = 0.41 nm showed a c-axis orientation; moreover, a Cr2O3(0001)/CeO2(100)∥STO(100) crystal relationship was obtained.
550
Masayuki Naoe, Tomoaki Omura, Toshiro Sato, Kiyohito Yamasawa and Yoshimasa Miura
The authors have fabricated the polycrystalline Li–Zn–Cu ferrite as a new temperature sensitive ferrite. The Li–Zn–Cu ferrite had high-frequency permeability profile and high electrical resistivity as well as the Ni–Zn–Cu ferrite for multilayered surface-mounting device such as a high-frequency chip inductor and filter. Since the new Li–Zn–Cu ferrite had both excellent high-frequency magnetic property and temperature sensitivity, it will be suitable for miniaturization of high-frequency inductive temperature sensing device. In this study, the relationship between grain size and the temperature-dependent magnetic properties of polycrystalline Li–Zn–Cu ferrite has been investigated. Three kinds of the Li–Zn–Cu ferrites sintered with Bi2O3 at different temperature were synthesized, and their temperature characteristics were evaluated. The most important result obtained is as follows: as the sintering temperature rose the coarse grain increased without changing bulk density, the permeability and its temperature dependence can be enhanced by grain growth due to higher sintering temperature. Therefore, the temperature dependent permeability of the Li–Zn–Cu ferrite can be controlled by grain size only without a change of the chemical composition.
554
Carl Matthias Intelmann, Karsten Hinrichs, Vitali Syritski, Florent Yang and Jörg Rappich
We investigated the change in Si surface recombination behaviour during the electrodeposition of ultrathin polypyrrole (PPy) films onto Si surfaces by means of in-situ pulsed photoluminescence (PL) spectroscopy. The quenching of the band-gap related PL is lower (better passivation) when the electrodeposition is performed in a less acidic solution by use of potential pulse sequences. In-situ infrared spectroscopic ellipsometry (IR-SE) was applied for the first time to PPy electrodeposition. IR-SE and PL measurements confirm negligible formation of SiOx species at the Si/PPy interface although aqueous electrolytes were used.
558
Zhanguo Li, Guojun Liu, Mei Li, Minghui You, Lin Li, Min Xiong, Yong Wang, Baoshun Zhang and Xiaohua Wang
We optimized the suitable growth conditions for obtaining smooth surface and high-quality InSb epilayer grown on semi-insulating GaAs substrate. The low temperature (LT) buffer layer was introduced into the growth process to improve the surface morphology and interface quality of the epilayers. It was confirmed that high quality InSb epilayer strongly depends on LT InSb buffer layer and growth conditions and parameters. Our typical InSb samples were obtained at the growth temperature of 420–425 °C, with the optimum Sb/In ratio of 1.4:1, and in our experiments, the epilayer thickness was in the range of 1.0 to 2.2 µm. Typically, the room temperature X-ray diffraction (XRD) full width half maximum (FWHM) of 172'' and mobility of 64300 cm2 V-1 S-1 at 77 K were obtained for typical sample of 2.2 µm thickness.
561
Akimori Tabata, Yusuke Komura, Yoshiki Hoshide, Tomoki Narita and Akihiro Kondo
Silicon carbide (SiC) thin films were prepared by hot-wire chemical vapor deposition from SiH4/CH4/H2 gases, and the influence of substrate temperature, Ts (104 < Ts < 434 °C), on the properties of the SiC thin films was investigated. X-ray diffraction patterns and Raman scattering spectra revealed that nanocrystalline cubic SiC (nc-3C-SiC) films grew at Ts above 187 °C, while completely amorphous films grew at Ts = 104 °C. Fourier transform infrared absorption spectra revealed that the crystallinity of the nc-3C-SiC was improved with increasing Ts up to 282 °C and remained almost unchanged with a further increase in Ts from 282 to 434 °C. The spin density was reduced monotonically with increasing Ts.
566
Takahiro Kida, Yohei Nagasaka, Takuya Sakurai, Tomohiko Yamakami, Rinpei Hayashibe, Katsuya Abe and Kiichi Kamimura
Microcrystalline SiC films were grown by hot-wire chemical vapor deposition (HW-CVD) at a low substrate temperature using a SiF4/CH4/H2 mixture, and their structural properties were characterized. Low growth pressure resulted in a narrow full width at half maximum (FWHM) of the Si–C peak in Fourier transform infrared absorption spectroscopy (FT-IR) spectra. The deposition rate and the FWHM value increased with increasing filament temperature. This seemed to be caused by change of the concentration ratio of precursors on the growth surface with increasing filament temperature. Also, the film crystallinity depended on the CH4/SiF4 flow rate ratio, and µc-3C-SiC(111) films were successfully obtained at low substrate temperature of 250 °C.
569
Hitoshi Miura, Kanji Yasui, Kazuki Abe, Atsushi Masuda, Yuichiro Kuroki, Hiroshi Nishiyama, Masasuke Takata, Yasunobu Inoue and Tadashi Akahane
The epitaxial growth of SiC on silicon-on-insulator (SOI) substrates with an ultrathin (<10 nm) top Si layer by hot-mesh chemical vapor deposition (CVD) was investigated. This method utilizes heated tungsten wires arranged in a mesh, which promotes the high decomposition efficiency of H2 gas. Using the hot-mesh CVD method, SiC epitaxial films were successfully grown on SOI substrates without voids being formed, which are formed readily in thin (<100 nm) top Si layers at temperatures above 800 °C. Some micropatterns for micro-electro-mechanical systems were fabricated on SiC on insulator (SiCOI) structure substrates by reactive ion etching and wet etching.
573
Yusuke Fukada, Kanji Yasui, Yuichiro Kuroki, Maki Suemitsu, Takashi Ito, Tetsuro Endou, Hideki Nakazawa, Yuzuru Narita, Masasuke Takata and Tadashi Akahane
GaN films were grown on AlN/SiC/Si substrates by hot-mesh chemical vapor deposition (CVD) using ruthenium (Ru)-coated tungsten (W)-mesh. When using the Ru-coated mesh, the crystallinity of the GaN films did not degrade until a mesh temperature of 1000 °C, while the crystallinity markedly degraded at lower than 1100 °C when using the W-mesh. From the photoluminescence (PL) spectra of GaN films grown using the Ru-coated W-mesh, strong near-band-edge emission without yellow luminescence can be observed. In order to elucidate the difference in the decomposition efficiency of ammonia gas, the hydrogen radical density generated by the heated W-mesh and Ru-coated mesh was also evaluated using tungsten phosphate glass plates.
577
Kensuke Akiyama, Satoru Kaneko, Teiko Kadowaki, Yasuo Hirabayashi and Hiroshi Funakubo
(110)-oriented epitaxial Fe3Si films were grown on (100) and (111) Si substrates with an epitaxial yttria-stabilized zirconia (YSZ) buffer layer by rf-magnetron sputtering. The epitaxial Fe3Si films contained a two-domain structure on the (100) substrate with a YSZ buffer layer, and a three-domain structure on the (111) substrate with a YSZ buffer layer. The coercive forces (Hc) of both epitaxial films were each approximately 40 Oe, and the saturation magnetizations (Ms) were each 850 emu/cm3, which are almost at the same level as those of bulk Fe3Si.
580
Hideyuki Toyota, Tomonori Sasaki, Shin-ichi Nakamura, Yoshio Jinbo and Naotaka Uchitomi
We prepared GaSb/AlGaSb multi-quantum-well (MQW) structures on n-type silicon (001) substrates by molecular beam epitaxy (MBE). To minimize dislocations in MQW layers and decrease the total thickness of the epitaxial layer, we employed not only an AlSb initiation layer but also a superlattice buffer layer (SL-BL) in a moderately thick GaSb buffer layer. For comparison we also fabricated other MQW structures on a considerably thick GaSb buffer layer without SL-BL. The obtained atomic force microscopy (AFM), transmission electron microscopy (TEM) images and high-resolution X-ray diffraction (XRD) patterns indicated that the definite MQW structures for both the samples and the quality of MQW layers prepared using SL-BL were generally better than those of the reference sample. The PL emission of these samples at about 1.30–1.55 µm was observed at room and low temperatures. The dependence of PL emission energy on GaSb well width was well explained by the finite square well potential model.
584
Takayuki Kamekawa, Hiroki Asami, Tsuneo Suzuki, Tadachika Nakayama, Hisayuki Suematsu, Takashi Yunogami and Koichi Niihara
Nickel copper oxide [(Ni1-xCux)O] thin films in which Cu content x was changed from 0 to 1 were prepared by pulsed laser deposition. The copper content of the thin films was determined by energy-dispersive X-ray analysis with scanning electron microscopy. Transmission electron microscope observation of the thin films with x = 0.37 revealed that the thin films contained grains consisting of Ni, Cu, and O. Both interplanar distances and lattice constant increased with increasing copper content. The (Ni1-xCux)O phase with 0 < x < 0.27 has a B1 structure.
588
Nozomu Tsuboi, Kenichi Tosaka, Satoshi Kobayashi, Keizo Kato and Futao Kaneko
The preparation of CuYO2 films on quartz glass substrates was carried out through the solution method using copper and yttrium nitrates as sources. Firstly, dip-coated films on the quartz glass substrates were annealed in air, and then annealed again under nitrogen flow. Continuous films were formed on the substrate surfaces. The films annealed in air at 900–950 °C were almost completely dominated by the Cu2Y2O5 phase, except for slight appearances of CuO and Y2O3. After annealing under nitrogen flow at 900–950 °C, the films were almost completely dominated by the CuYO2 phase, except for slight appearances of Cu2O and Y2O3. The slight appearances of the impurity phases are possibly related to slight variations in the concentration ratio of the copper source to the yttrium source within the dip-coated films. The nitrogen-annealed films, as well as bulk CuYO2, exhibited a green emission band owing to the Cu+ interconfiguration transition from 3d94s1 to 3d10 with the Stokes shift, being consistent with the dominant appearance of the CuYO2 phase.
592
Nozomu Tsuboi, Tomohiro Moriya, Satoshi Kobayashi, Hidehiko Shimizu, Keizo Kato and Futao Kaneko
As-deposited films were prepared on sapphire substrates at 500–680 °C by alternately sputtering Cu and Al targets in Ar-diluted O2 gas atmosphere. The composition of the as-deposited films corresponded to that of the slightly oxygen-rich region of the CuO–CuAl2O4–Al2O3 system. The films as-deposited at 500 °C had an amorphous structure, while the films as-deposited at 680 °C had CuAl2O4 phase but no CuAlO2 phase. Annealing at 1050 °C in nitrogen flow caused a reduction in the molar fraction of oxygen, i.e., the composition of the annealed films with [Cu]/[Al] ≈1 corresponded to CuAlO2. The annealed films were predominated by the CuAlO2 phase. The preferential orientation of the films toward the c-axis normal to the substrate surface is due to the small lattice mismatch between the rhombohedral [010] of delafossite-type CuAlO2 and the hexagonal [1100] of the sapphire substrate. The annealed films had an absorption edge corresponding to the energy gap of CuAlO2 and exhibited p-type conductivity.
596
Yusuke Miyamoto, Kunihiko Tanaka, Masatoshi Oonuki, Noriko Moritake and Hisao Uchiki
Cu2ZnSnS4 (CZTS) thin films were prepared by a sol–gel sulfurization method. One sample (CZTS1) was stoichiometric (Cu : Zn : Sn : S = 2.0 : 1.0 : 1.0 : 4.0) and another sample (CZTS2) was Cu poor and Zn rich (Cu : Zn : Sn : S = 1.87 : 1.15 : 1.00 : 4.00). Photoluminescence from the CZTS thin films was studied as a function of excitation power and temperature. The CZTS1 and CZTS2 thin films showed a broad luminescence between 1.1 and 1.4 eV and between 1.1 and 1.45 eV respectively. The peak photon energy of the photoluminescence was shifted to higher energy side when the excitation power was increased. The origin of the photoluminescence was attributed to donor-acceptor pair recombination with activation energy of 39 and 59 meV for CZTS1 and CZTS2 respectively. Transmittance spectra for the thin films were studied as a function of temperature. The band gap energy shift was smaller than by 10 meV with increasing temperature from 22 to 300 K.
598
Kunihiko Tanaka, Noriko Moritake, Masatoshi Oonuki and Hisao Uchiki
Cu2ZnSnS4 (CZTS) thin films were prepared by sulfurizing pre-annealed oxyhydrate precursors deposited by the sol–gel method. The precursors were obtained by coating solutions containing copper(II) acetate monohydrate, zinc(II) acetate dihydrate, tin(II) chloride dihydrate, 2-methoxyethanol, and monoethanolamine on a soda lime glass (SLG). By pre-annealing the precursors in air at 560 °C, chemical composition of films was almost stoichiometric, transmittance of IR region was increased and number of void was decreased while chemical composition of CZTS films deviated considerably from stoichiometry when the precursors were annealed N2+H2 (5%) atmosphere at 460 and 560 °C.
602
Katsuhiko Moriya, Kunihiko Tanaka and Hisao Uchiki
Cu2ZnSnS4 (CZTS) precursors were prepared by pulsed laser deposition while controlling the energy density to eliminate grains of Cu–Sn–S compounds. The precursor prepared with an energy density of 0.7 J/cm2 was flat and of better quality than the precursor prepared with an energy density of 1.5 J/cm2. The precursors were annealed in N2+H2S (5%) atmosphere. As a result of annealing, the decrease of the compositional ratio of sulfur was suppressed and the films became nearly stoichiometric. Some peaks in the an X-ray diffraction pattern of thin films are attributed to (112), (220), (312), and (200) planes of CZTS. The direct band-gap energy of the film annealed at 500 °C was about 1.5 eV, which is very close to the optimum value for a solar-cell absorber, and hence was used for a solar cell. The CZTS thin film solar cell with an active area of 0.12 cm2 showed an open-circuit voltage of 336 mV, a short-circuit current of 6.53 mA/cm2, a fill factor of 0.46, and a conversion efficiency of 0.64%.
605
Keiichi Murai, Hisayuki Suematsu, Weihua Jiang, Kiyoshi Yastui and Koichi Niihara
We have proposed a method using electron microscopy and the gas adsorption method to determine the submicrometer-particle content quantitatively in powder prepared by pulsed wire discharge. The mean surface diameter obtained by the gas adsorption method was larger than that obtained by electron microscopy. The submicrometer-particle content was successfully calculated by the ratio of mean surface diameters. It was found that this method made quantitative determination of the submicrometer-particle content possible.
609
Masahide Nakakuki, Akihiro Shiono, Isao Kobayashi, Noriaki Tajima, Tomohiko Yamakami, Rinpei Hayashibe, Katsuya Abe, Kiichi Kamimura, Motoki Obata and Mitsunori Miyamoto
A novel submount substrate with high thermal conductivity for optoelectronic devices is proposed. The substrate is fabricated by depositing an Al-based insulating film on a copper substrate. AlN films were deposited by RF reactive sputtering using an Al target (5N) in a gas mixture of Ar and N2. Al2O3 films were deposited by oxygen-ion-assisted electron beam (EB) evaporation. Many conductive paths were detected in the AlN films. These defects were introduced in the AlN film during a photolithography process for fabricating electrode patterns because the alkaline developer dissolved the film. An Al–OH peak in Fourier transform infrared spectroscopy (FT-IR) spectra suggested that the Al(OH)3 formation was one of the reasons for the presence of conductive paths in the AlN film. In the case of Al2O3 films, no conducting path was detected in electrical measurements, and no marked change in surface morphology was observed in scanning electron microscopy (SEM) images, after treatment with the alkaline developer. The Al2O3/Cu structure is a candidate for the novel submount substrate with high thermal conductivity.
612
Qixin Guo, Tooru Tanaka, Mitsuhiro Nishio and Hiroshi Ogawa
We report the structural and optical properties of AlInN films grown on (0001) sapphire substrates by reactive radio-frequency (rf) magnetron sputtering using aluminum and indium targets in an ambient of argon and nitrogen. X-ray diffraction analysis and atomic force microscopy show that AlInN films with a smooth surface can be obtained and that the lattice constant for the c-axis obtained from the (0002) diffraction peak of the AlInN films decreases with an increase in the Al composition x. Optical transmittance and reflectance spectra analysis reveals that the AlInN films are of a direct bandgap structure as AlN and InN. The bandgap energy of the AlInN films can be tailored by varying the ratio of the rf power of the indium target to that of the aluminium target.
616
Saki Kondo, Kenji Tateishi and Nobuo Ishizawa
The evolution of the corundum (α-Al2O3) structure was investigated at 297, 573, 873, and 1173 K using the single-crystal X-ray diffraction method and molecular dynamics simulation. The results were smoothly extrapolated to the previously reported high-temperature data of the compound at 2170 K [Ishizawa et al.: Acta Crystallogr., Sect. B 36 (1980) 228], revealing a significant shift of the fractional coordinate z of the Al atom as a function of temperature. The Al atom shift indicates that the Al…Al intermetallic repulsion force across a pair of face-sharing octahedra becomes conspicuous over other interatomic forces at high temperatures. The increasing Al…Al repulsion is relieved by both the preferential expansion of a unit cell along the c-axis and the change in the z coordinate of the Al atom. The results of molecular dynamics simulation experiments qualitatively agreed with the X-ray diffraction data. The thermal expansion of the crystal was well described by the quadratic functions, a = 4.75385 (1.0 + 5.05841×10-6T + 1.69084×10-9T2) Å, and c = 12.9782 (1.0 + 4.61344×10-6T + 2.63802×10-9T2) Å.
620
Masaru Sato, Mayumi B. Takeyama, Eiji Aoyagi and Atsushi Noya
As an extremely thin diffusion barrier applicable to Cu interconnects for the 45 nm technology nodes, we propose a barrier material without interface layers that can become a cause of barrier consumption owing to solid-phase reaction and/or intermixing. We examine the barrier properties of a reactively sputtered ZrN barrier as thin as 5 nm between Cu and SiOC. The ZrN barrier with a slightly N-rich composition tolerates annealing at 500 °C for 30 min. Transmission electron microscopy indicates the absence of interface layers adjoining the barrier. Using the ZrN barrier, we can demonstrate the effectiveness of the interface-layer-free characteristics for an extremely thin barrier of high performance.
625
Aishi Yamamoto, Yoshiyuki Kikuchi, Atsushi Ishizumi, Hisao Yanagi, Hiroyuki Iwai and Tsukasa Yoshida
The photoluminesecence (PL) of porous ZnO films modified with Eu3+ ions was studied. The samples were fabricated by electrodeposition using eosin Y (EY) dye molecules. Scanning electron microscopy images and X-ray diffraction patterns showed that the porous films have nanometer-scale networks and become finer with increasing EY concentration. Sharp PL peaks due to the intra-4f transitions of Eu3+ ions were clearly observed. The PL peak intensity was higher in finer porous films. The temperature dependence and decay profiles of the PL intensity indicated that capping Eu3+ ions with 4,4,4-trifluoro-1-(2-thienyl)-1,3-butanedione (TTA) were effective for enhancing PL intensity. Furthermore, PL excitation spectra were observed and the excitation of Eu3+ ions was discussed.
629
Katsuya Teshima, Yuki Niina, Kunio Yubuta, Tatsuo Nakazawa, Takaomi Suzuki, Toetsu Shishido, Nobuo Ishizawa and Shuji Oishi
Idiomorphic and prismatic K2Nb8O21 crystals were successfully grown by the isothermal evaporation of KCl flux. On the basis of their aspect ratio, the crystals were divided into two morphological types, that is, whisker (needle) and prism. Growth was induced by heating mixtures of KCl and Nb2O5 at 1100 °C for 60 h followed by quenching in a furnace with the electric power turned off. The obtained K2Nb8O21 crystals were colorless and transparent. Whiskers having an average size of approximately 160×11.1 µm were grown from high-temperature solutions containing Nb at 1–30 mol %. The grown crystals had roundish or prismatic one-dimensional forms, and their surfaces were very smooth. Their generation and sizes were obviously dependent on the Nb concentration of the starting mixtures. The K2Nb8O21 crystals exhibited high activity for dye adsorption and degradation. The degradation occurred via a photocatalytic process under ultraviolet light irradiation.
633
Yusuke Iida, Hideaki Takashima and Yoshinori Kanno
V2O5 thin films were prepared by pulsed laser deposition (PLD). We studied the response of the phosphorescence energy of the double bond between vanadium and oxygen (V=O) on basicity. The results show that the insertion of Li+ leads to a blue shift of the wavelength for the V=O peak with increasing electric charge. The V2O5 thin films, soaked in dimethylsulfone (DMSO2), acetone, and dilute HNO3 solutions, also lead to a blue shift of the wavelength for the V=O peak. In addition, the electrical properties of the V2O5 thin films were studied by atomic force microscopy (AFM). The current–voltage (I–V) characterization of V2O5 thin films (Ts = room temperature, PO2 = vacuum) shows erasing, metastable reproducing and recording states. The reversibility of phase transitions for V2O5 thin films depends on the conditions for fabrication by PLD.
637
Hiroshi Sugimoto, Hirokazu Tanaka and Yoshinori Kanno
We fabricated a quartz crystal microbalance (QCM) coated with inorganic films for volatile organic compound (VOC) gas sensing. The deposited materials were SiO2, TiO2, and Al2O3. Inorganic films were formed on a quartz electrode by pulsed laser deposition (PLD) and/or a sol–gel method. The TiO2 film had the highest sensitivity due to its large surface area. VOC gases were dichloromethane, carbon tetrachloride and toluene. Toluene showed the largest amount of adsorption onto the inorganic films. Sol–gel-coated TiO2 had about quintuple sensitivity, compared with PLD-coated TiO2.
640
Fan Zhang, Tomoaki Karaki and Masatoshi Adachi
Nanosized Bi4Ti3O12 (BIT) powders were prepared by a simple coprecipitation process. Differential scanning calorimetry (DSC) measurement was carried out to estimate the phase transition temperatures of the BIT powders calcined at different temperatures. The results showed a range of coexistence of the BIT and Bi2Ti2O7 phases at calcination temperatures from 600 to 650 °C. The dielectric constants of ball-milled BIT powders calcined at different temperatures were measured. It was found that the samples had a value of around 190, which is higher than that of BIT bulk ceramics.
644
Yong Choi and Sang Hyun Lee
Quasi-nano sized BaxZn1-xFe2O4 ferrites were prepared using self-propagating high-temperature synthesis (SHS) with different initial compositions of BaO2 and ZnO and various oxygen partial pressures of 0.25–1.0 MPa. The combustion temperature and the combustion propagating rate increased with decreases in the molar ratio of barium oxide to zinc oxide and oxygen partial pressure in the ranges of 860–1208 K and 4.9–6.0 mm/s, respectively. As the oxygen pressure during SHS reaction increased from 0.25 to 1.0 MPa, the maximum magnetization (Ms) level, the residual magnetization (Mr) level and the coercive force (iHc) changed from 0.580 to 1.932 A·m2/kg, from 0.110 to 0.472 A·m2/kg, and from 12.49 to 24.11 kA/m, respectively.
647
Tadashi Fujii, Hiroaki Matsunaga and Masatoshi Adachi
The micropatterning of ferroelectric thin films is a valuable technology for realizing high-density ferroelectric random access memories, sensors and actuators. We fabricated 500-nm- to 20-µm-sized circular dots of (Pb,Sr)TiO3 micropatterns by an electron-beam-induced reaction process using a scanning-electron-microscope-based electron beam lithography system. The piezoelectric response was observed in 10-µm-sized dots by piezoresponse scanning force microscopy. Using an atomic force microscope, every fabricated dot pattern was found to have a mesa shape. To obtain 100-nm-sized dots with high density, further optimization of EB irradiation and crystallization conditions is necessary.
649
Tsutomu Asakawa, Daisuke Nagano, Satoshi Denda and Keiichi Miyairi
The hydrogen distribution in tantalum and tantalum oxide thin films has been examined by secondary ion mass spectrometry (SIMS). Tantalum and tantalum oxide thin films implanted with deuterium were analyzed by conventional SIMS. Metal–insulator–metal (MIM) devices were analyzed by backside SIMS. The results of these measurements show that the hydrogen distribution is concentrated on the front side in tantalum films, while the hydrogen distribution in tantalum oxide films is not affected by SIMS measurement. A model has been proposed to explain the cause of an anomalous hydrogen peak forming at the interface between the tantalum oxide and tantalum films in the MIM devices. In the model, when the tantalum oxide film covering the tantalum film is removed by primary ion beam sputtering, hydrogen atoms in the tantalum film are quickly discharged to a vacuum in a sample chamber and the anomalous hydrogen peak is detected.
Electrical and Optical Propteties of Inorganic Materials
653
Don Klaitabtim, Sirapat Pratontep and Jiti Nukeaw
Nitrogen-doped zinc oxide (N:ZnO) films on glass substrates have been prepared by the reactive gas-timing rf magnetron sputtering of ZnO targets in a mixture of argon and nitrogen gases. Using this gas-timing technique, N:ZnO films were produced without any substrate heating. The nitrogen partial pressure during the sputtering process was periodically controlled by an on-off sequence. The structural and optical properties of the fabricated films were analyzed by X-ray diffraction (XRD) and optical absorption spectroscopy, respectively. The nitrogen composition of the N:ZnO films was quantified by X-ray photoelectron spectroscopy (XPS). In this study, we focused on investigating the effects of the nitrogen flow rate and the rf power on the structural properties, the nitrogen doping efficiency, and the optical band gap of N:ZnO films. A slight shift in the optical band gap to a higher energy was found when the nitrogen flow rate was increased or when the rf power was decreased. This coincides with an improvement in the crystallinity of the films. Gas-timing rf magnetron sputtering deposition is a simple method of fine-tuning material properties by slight modifications to the existing sputtering technique.
657
Joel T. Asubar, Ariyuki Kato, Yoshio Jinbo and Naotaka Uchitomi
ZnSnAs2 thin films were prepared by molecular beam epitaxy (MBE) on semi-insulating (001) InP substrates using the same growth conditions as previously reported. High-resolution X-ray diffractometry (HRXRD) and Raman spectroscopy studies suggest the presence of both the chalcopyrite and sphalerite phases. The transport properties were measured from 5 K up to room temperature. We observed a pronounced peak in the Hall coefficient temperature dependence curve at ∼130 K, similar to those observed only from chalcopyrite-phase bulk ZnSnAs2 in earlier studies. A hole concentration of p = 5.98 ×1018 cm-3, hole mobility of µ= 23.61 cm2/(V·s) and resistivity of ρ= 4.43 ×10-2 Ω·cm were obtained at room temperature.
661
Takahiro Suzuki, Tadachika Nakayama, Tsuneo Suzuki, Hisayuki Suematsu and Koichi Niihara
Some normal chain alcohols with various carbon chain numbers were applied to NiFe2O4 porous bulks in order to examine the mechanisms underlying the abrupt gradient change of the temperature dependence of electrical resistivity. As a result, it was discovered that the temperature at which the gradient changes of the electrical resistivity were different for adsorped alcohols with different carbon chain numbers. The evaporation and temperature of alcohols were related to the temperature of gradient change, therefore, alcohol adsorption or desorption and/or other chemical reactions were the cause of the gradient change.
664
Satoru Kaneko, Kensuke Akiyama, Masahiko Mitsuhashi, Takeshi Ito, Masao Kumagai, Hiroshi Funakubo and Mamoru Yoshimoto
The multilayered structure of bismuth cuprate superconducting film (Bi2Sr2Ca1Cu2OX/Bi2Sr2Cu1OX) affects the supercell consisting of several unit cells as well as the lattice constant of each layer. A relatively thick film of epitaxial Bi2Sr2Ca1Cu2OX (Bi-2212) was prepared to determine its crystal structure and to compare with a reference film of ∼1000 Å thickness and a multilayered structure. As the Bi-2212 film grew continuously, the film was rotated by 32° around the surface normal with respect to the initial layer of Bi-2212. The angle can be interpreted according to the coincidence site lattice (CSL) with Σ 17 and 18.
667
Yusuke Iida and Yoshinori Kanno
V2O5 thin films were prepared by pulsed laser deposition (PLD). Ag-doped V2O5 thin films were prepared by the reaction between V2O5 thin films and 1 M AgNO3 solution for 3 min. Photochromism and photoelectrochromism in V2O5 and Ag-doped V2O5 thin films were investigated. Absorption spectra measurement results show that V2O5 and Ag-doped V2O5 thin films are colored by ultraviolet light irradiation and bleached by visible light irradiation. Furthermore, we can conclude that the response of Ag-doped V2O5 thin films to ultraviolet light irradiation is rapid. Photoluminescence (PL) measurements show that the photochromic system of Ag-doped V2O5 thin films is by the photooxidation of Ag to Ag+. In the bleaching process by electrochemical method, the response of Ag-doped V2O5 thin films was better than that of V2O5 thin films.
671
Hirokazu Tanaka, Hiroshi Sugimoto and Yoshinori Kanno
An analytical technique using AT-cut 9 MHz quartz crystal microbalance (QCM) mist sensors coated with lipid film [dimethyl didodecylammonium poly(styrene sulfonate) (2C12N+/PSS-)] was investigated. The mist sensors coated with lipid films had a different sensitivity to volatile organic compounds (VOCs), whose fine mists were produced by ultrasonic vibration using an atomizer. The VOCs used for mists are formaldehyde and toluene. The frequency shift of the sensor coated with the film is significantly higher than that of the sensor without the films. The surface morphology of the sensor coated with the films is more rugged than that of the sensor without the films. The diversity of surface structure contributes to the improvement of QCM sensitivity.
Inorganic Devices
676
Yoshiki Ishida, Chen Chen, Masataka Hagihara, Tomohiko Yamakami, Rinpei Hayashibe, Katsuya Abe and Kiichi Kamimura
Nitrided layers were grown on a 4H-SiC(0001) by plasma nitridation method using NH3. Nitridation was enhanced with increasing RF power and with decreasing growth pressure. However, the exact capacitance–voltage (C–V) properties of the nitride layer/SiC interface could not be determined because of the leakage current. The SiO2 film was deposited on the nitrided layer by thermal chemical vapor deposition method using tetraethoxysilane (TEOS) omit obtain an insulating film with sufficient thickness and an exact interface property. The interface state density Dit was evaluated from C–V characteristics by the Terman method. It was indicated that Dit near the mid gap of the TEOS oxide/nitride layer structure was higher than those of the TEOS–SiO2 films and thermal oxide film. The Dit of the oxide/nitride layer successfully decreased by post NH3 annealing.
679
Gwo-Mei Wu, Kung-Yu Cheng, Chia-Hui Fang, Tzer-En Nee, Jen-Cheng Wang, Nie-Chuan Chen, Yeu-Jent Hu, Jiunn-Chyi Lee and Ya-Fen Wu
We studied the unique correlations between the electrical and optical characteristics of InGaN/GaN multiple quantum well (MQW) light-emitting diodes (LEDs) with n-AlGaN layer and n-InGaN/GaN superlattice electron tunneling layer (ETL). It was found that the ideality factor of the two devices increased with decreasing temperature from 300 to 20 K. Levine's model was used to characterize the anomaly, and the ideality factor could be shown as a function of temperature by n = 1 + To/T. The device with ETL inherently exhibited a large pseudo-temperature To with a large characteristic energy and charge population in the multilayer interface, over wide temperature and voltage ranges. Owing to the more interface state distribution and the less effective density of state (DOS) in the quantum wells, the excitons formed in the ETL sample augment the spectral radiations at temperatures higher than 150 K. The carrier tunneling processes via the extent of charge population consequently caused anomalous To and resulted in the abnormal deterioration of the EL intensities with a small density of state.
682
Hiroyuki Endo, Shingo Hiratsuka, Hiroshi Kitamura, Toshinari Takamatsu, Makoto Hosoda and Naoki Ohtani
The authors investigated the electric-field dependence of photoluminescence (PL) spectra in a GaAs/AlAs multi-quantum well (MQW) structure, in which QWs with different thicknesses coexist. PL properties in this sample are chiefly determined by the coexistence of 21-monolayer (ML) and 23-ML QWs, because the islands of 22-ML QWs are too small to have an effect on radiative processes. Two PL signals are found in the shorter-wavelength region, caused by X1–Γ2 resonances, because the different thicknesses of GaAs QWs lead to different resonant voltages and wavelengths. We also estimated the carrier densities of excited states from the observed two PL intensities and by calculations of overlap integrals of wave functions between electron and heavy-hole states. This result clearly indicates that the carrier density in the Γ2 in the 21-ML QW becomes larger than that in the 23-ML QW when the X1–Γ2 resonance of the 21-ML QW occurs. This demonstrates that interface imperfection creates novel carrier transport paths and affects carrier densities as well as optical properties in excited states in MQW structures.
685
Toshio Kurobori, Yoshihiro Obayashi, Kenji Suzuki, Yukio Hirose, Toshiaki Sakai and Shin-ichiro Aoshima
Fine-pitched microgratings either on or beneath surface of bulk lithium fluoride (LiF) are holographically fabricated by interfering with the second harmonic (400 nm) of a mode-locked Ti:sapphire oscillator–amplifier laser. The laser-active F2 and F3+ color centers in LiF are excellent candidates for producing visible laser action from the green-to-red spectral range when excited with a single wavelength. Here a green distributed feedback (DFB) laser action with a narrower oscillating linewidth is demonstrated by utilizing simultaneous formation of the F3+ color centers and waveguide with the microgratings encoded by interference of 400 nm femtosecond laser pulses. In addition, the possibility of a dual-beam DFB laser based on these color centers in LiF is discussed.
689
Leke Wu and Wenzhong Shen
Employing the concept of photon frequency upconversion, we have proposed two types of semiconductor upconverters to realize pixelless far-infrared (FIR) imaging. The upconverter consists of a GaAs FIR homojunction interfacial work-function internal photoemission detector integrated with a GaAs/AlGaAs near-infrared light-emitting diode (LED), or GaN/AlGaN mid-IR/FIR dual-band heterojunction detector with a GaN/AlGaN violet LED. We have studied in detail the dependences of the modulation transfer function and quantum efficiency of the upconverters on various device parameters. Through the application of resonant cavity to the GaAs-based upconverter, we can expect sharp and high-resolution image and improved quantum efficiency. In addition, due to the large light absorption in the GaN/AlGaN heterojunction detector, the quantum efficiency of the GaN-based upconverter is much higher than that of GaAs-based one.
694
Yoshiyuki Chiba, Akira Yamada, Makoto Konagai, Yoshihiro Matsuo and Takahiro Wada
Cu(InGa)Se2 (CIGS) thin films have been successfully grown by a mechanochemical process (MCP), which is a low-cost process, without any additional heating. In this study, we carried out low-temperature photoluminescence (PL) measurements for CIGS films prepared by the MCP. The CIGS films with Ga contents of 1 and 5% showed four radiative recombinations. The emission peaks of 0.97 and 0.90 eV were assigned to free-to-bound and donor–acceptor pair transitions, respectively. The other two peaks were the phonon replicas. The film which exhibited high conversion efficiency shows the emission of a free exciton. From the free exciton energy, we inferred that the acceptor and donor defects were VCu and VSe, respectively. These results suggested that the films grown by mechanical synthesis possess intrinsic defects identical to those in films deposited by a vacuum process.
Electrical Properties of Nano-materials
697
Shunsuke Odaka, Hisao Miyazaki, Takuya Moriki, Takashi Sato, Akinobu Kanda, Kazuhito Tsukagoshi, Yoichi Ootuka and Yoshinobu Aoyagi
Nanoscale channel formation and characterization in ultrathin graphite film are performed. Two narrow channels with a submicron square connected in series are patterned by electron-beam lithography followed by oxygen plasma etching. The patterned film showed Coulomb blockade oscillations in the source–drain current upon a gate voltage change at 4.2 K. The Coulomb blockade effect occurred due to the electric potential modulation in the narrow graphite channels.
700
Shinji Ide, Masato Yoshikuni, Nobuyuki Iwata and Hiroshi Yamamoto
For applications to a novel low-voltage acceleration field emission display, carbon nanofiber (CNF) emitters were fabricated using a screen printing method. The two types of CNF of different lengths, normal-length CNFs, and cut CNFs were examined. A current density of 1.4 mA/cm2 was achieved at 10 V/µm in CNF emitters prepared from the paste composed of normal-length CNFs (1 wt %), glass paste (6 wt %), and gold nanometal ink (30 wt %). The field enhancement factor β in the Fowler–Nordheim equation was ca. 5800. CNF emitters without gold nanometal ink showed low performance. Emitter performance was determined on the basis of the results of scanning electron microscopy (SEM) and field emission characteristics.
703
Yue-Lin Huang, Meng Hsien Chou, Sheng Yun Wu and Chia-Liang Cheng
Spatially well separated cupric oxide (CuO) nanowires grown using thermal oxidation method were examined to directly observe the scale structure evolution of lattice vibration modes. Scanning electron microscopy and high-resolution transmission electron microscopy studies revealed the single crystalline nature and microstructure of a single CuO nanowire. Phonon spectral evolution along the wire axis was investigated using confocal Raman spectroscopy by scanning a single nanowire. The Ag, Bg(1), and Bg(2) phonon modes of CuO that are quantum-confined in radial directions of the thin nanowire evidenced from the observed systematic red-shift, broadening of the peak profile. These results can be well explained based on the phonon confinement model.
Magnetic Properties of Nano-materials
706
Sheng Yun Wu, Jhong-Yi Ji and Po-Hsun Shih
A weak surface magnetic anisotropy was observed in the thermal deviation of the saturation magnetization of Cu2O nanoparticles. The thermal deviation of the saturation magnetization is clearly a departure from the Bloch T3/2 law expected for isotropic systems, signaling the onset of magnetic anisotropy, and is presumably due to the high surface-to-volume ratio of the nanoparticles, and the surface atoms give rise to polarized moments. Here, we assume a uniaxial anisotropy and adopt the Heisenberg ferromagnet model for the applied magnetic field Ha-aligned moment-carrying Cu2O nanoparticles, and the surface magnetic anisotropic energy gap Δ can then be obtained from the fit, indicating that the anisotropic energy gap Δ can only be revealed at low temperatures.
Nano-Process and Technologies
712
Takumi Ogino, Shinya Nishimura and Jun-ichi Shirakashi
Scanning probe microscope (SPM) scratching with a diamond-coated tip on a Si surface was performed in a low-force regime of less than 9 µN. The influence of various scan parameters on the groove size was investigated. The groove size could be precisely controlled by the applied force, scan direction, and the number of scan cycles. There is no effect of the scan speed on the groove size. It is concluded that high-speed nanolithography can be achieved without the degradation of patterns by SPM scratching. Using this method, more complex nanostructures such as a line and space pattern with a pitch of 30 nm and a dot array of 2.6 ×1010 cm-2 density were successfully fabricated on a Si surface.
715
Shinya Nishimura, Takumi Ogino and Jun-ichi Shirakashi
We have studied micrometer-scale scanning probe microscopy (SPM) local-oxidation lithography on Si. In order to perform large-scale oxidation, an SPM tip with a contact area of 2.5 ×1.9 µm2, which is about 12,000 times larger than that of a conventional SPM tip, was prepared. The width of the Si oxide produced was clearly determined by the contact length of the tip. Furthermore, the throughput reached 125 µm2/s, which is 10,000 times larger than that of conventional SPM local oxidation. The SPM tip with a larger contact area may increase the spatial dimension of the water meniscus, resulting in a larger oxidized area. It is suggested from our results that SPM local oxidation can be upscaled by using a larger tip radius.
718
Shinya Nishimura, Takumi Ogino, Yasushi Takemura and Jun-ichi Shirakashi
Local-oxidation nanolithography by scanning probe microscopy (SPM) has enabled us to fabricate nanometer-scale oxide wires on Si surfaces. Here, we investigate the size dependence of the wires on the dynamic properties (oscillation amplitude, Q-factor) of the cantilever used in tapping-mode SPM local oxidation. With the enhancement of oscillation amplitude from 72 to 432 nm at a natural Q-factor of 505, the width and height of the Si oxide wires were controlled and ranged from 31.3 to 18.3 nm in width and from 1.5 to 0.4 nm in height, respectively. On the other hand, when the amplitude was fixed at a natural value of 144 nm, local oxidation with a low Q-factor of 193 realized an oxide wire with a width of 33.7 nm and a height of 1.2 nm. At a high Q-factor of 1665, the width and height of the fabricated Si oxide wire were 24.9 and 1.0 nm, respectively. These results imply that the size of the oxide wire is more strongly affected by the oscillation amplitude of the cantilever than the Q-factor.
721
Yusuke Taki, Makiko Kikuchi, Kiyoaki Shinohara and Akira Tanaka
The synthesis of vertically aligned single-walled carbon nanotube (SWCNT), double-walled carbon nanotube (DWCNT), and triple-walled carbon nanotube (TWCNT) films has been achieved by a combination of radiation-heated chemical vapor deposition (RHCVD) and long-throw sputtering. The proportions of specific walled CNTs/as-grown CNTs are as follows: SWCNT/CNT ratio of 87%, DWCNT/CNT ratio of 83%, and TWCNT/CNT ratio of 62%. When the population density of vertically aligned CNTs on a substrate ranges from 1.1 ×109 to 7.1 ×1010 bundles/cm2, the selective growth of graphene walls of CNTs is achieved. As outer diameters and the number of graphene walls of CNTs increase, CNTs grow longer. It is considered that the larger the metallic catalyst diameter, the longer the catalyst lifetime.
725
Yusuke Taki, Kiyoaki Shinohara, Makiko Kikuchi and Akira Tanaka
Radiation-heated chemical vapor deposition (RHCVD) is a newly developed process which enables the maintenance of narrow catalyst diameter distributions until carbon nanotubes (CNTs) start growing and the synthesis of single-walled carbon nanotube (SWCNT), double-walled carbon nanotube (DWCNT), and triple-walled carbon nanotube (TWCNT) films by changing catalyst diameters. The proportions of specific walled CNTs/as-grown CNTs are as follows: SWCNT/CNT ratio of 100%, DWCNT/CNT ratio of 88% and TWCNT/CNT ratio of 76%. It is clarified that CNT diameter and the number of graphene walls of CNTs are proportional to catalyst diameter.
730
Toshiya Murakami, Yuki Hasebe, Kengo Higashi, Kenji Kisoda, Koji Nishio, Toshiyuki Isshiki and Hiroshi Harima
Single-walled carbon nanotubes (SWNTs) were grown by catalytic chemical vapor deposition on SiO2 substrates. By thinning the substrate before growth, the morphologies of the SWNTs and their seed catalyst particles were simultaneously observed in the as-grown state by plan-view transmission electron microscopy (TEM). Analysis over a wide area of the substrate showed that the diameters of the SWNTs d and those of the catalyst particles D had different distributions. The catalytic activity was size-dependent: fine particles (D\lesssim4 nm) yielded the same diameter SWNTs (d∼D), and intermediate sizes (∼4 < D\lesssim6 nm) yielded finer tubes (d < D), while larger particles (D\gtrsim6 nm) had no catalytic activity. We also found that the small catalyst particles with D of less than 5 nm that appeared during the growth process by chemical reactions with the carbon source mainly contributed to the growth of SWNTs.
735
Katsuya Teshima, Nobutaka Shikine, Ryota Hayakawa, Kunio Yubuta, Takaomi Suzuki, Morinobu Endo, Toetsu Shishido and Shuji Oishi
Molybdenum dioxide (MoO2)/carbon nanofiber composites were successfully fabricated by LiCl–KCl flux cooling. The preparation was obtained by heating mixtures of MoO3, LiCl, KCl, and carbon nanofibers at 500 °C for 10 h and then carrying out quenching in a furnace with the electric power turned off. The obtained MoO2/nanocarbon composites were blackish and had a metallic luster. The obtained composites have lengths of about 5–150 µm and are in the form of prism. The carbon nanofibers and MoO2 crystals were interfused densely with each other. Carbon nanofibers were found to act as a reducing agent.
738
Takayuki Hirai, Yoshinori Kanno and Yoshiki Takagi
This paper describes a series of experiments to grow nanocrystalline diamond (NCD) in a closed system hot filament chemical vapor deposition (HFCVD) reactor using acetone containing various amounts of water. A commercial acetone includes a slight amount of water, so we tried to dehydrate from the acetone. Next, diamond was synthesized under the various type of water content. We investigate about an optimum acetone/water concentration ratio in diamond particle formation and film formation. We clarified the effect of water concentration on the morphology, nucleation density and size. The morphology, and grain size and structure of the diamond were examined with field emission scanning electron microscopy (FE-SEM) and Raman spectroscopy. We will refer to the synthesis process in detail about diamond and NCD.
741
Ruiqian Guo, Jun Nishimura, Masato Matsumoto, Mitsuhiro Higashihata, Daisuke Nakamura and Tatsuo Okada
Vertically aligned ZnO nanowires with controllable density were successfully synthesized by nanoparticle-assisted pulsed-laser deposition (NAPLD), by which nanoparticles formed in the gas phase by the condensation of the ablated species are transported onto the substrate, and nanoparticles play an important role in density control. The effects of synthesis conditions on the density and optical properties of ZnO nanowires were investigated in detail. With the increase in repetition rate and laser energy, ZnO nanowires with a higher density can be obtained as a result of a larger quantity of nanoparticles formed in the gas phase. The density-controlled growth also depends on substrate–target distance. UV emission was observed from all the obtained nanowires at about 390 nm without visible fluorescence near 500 nm due to their excellent crystallinity and the oxygen-deficient defect.
746
Chia-Cheng Wu, Dong-Sing Wuu, Tsai-Ning Chen, Ting-En Yu, Po-Rung Lin, Ray-Hua Horng and Hsin-Yi Lai
ZnO nanowall networks with a honeycomblike pattern on GaN/sapphire substrates were deposited by metalorganic chemical vapor deposition (MOCVD) without using any metal catalysts. The effects of growth temperature and VI/II ratio on the surface morphology and optical properties of ZnO nanowall networks were investigated by scanning electron microscopy (SEM) and photoluminescence (PL) analysis. The SEM image obtained shows a prominent nanowall-network structure when the growth temperature is higher than 550 °C. The wall width and network size of ZnO nanowall-network structures grown by MOCVD were found to change depending on DEZn flow rate. The surface morphology of ZnO structures was observed at different time intervals from 10 to 40 min to investigate the formation mechanism of ZnO nanowall networks. The room-temperature PL measurement of ZnO nanostructures grown on GaN/sapphire substrates shows high-intensity ultraviolet peaks at 385 nm without any “green peak”. The PL spectrum suggests that the quantum confinement effects are caused by the nanostructure of ZnO.
751
Jaturong Jitputti, Sorapong Pavasupree, Yoshikazu Suzuki and Susumu Yoshikawa
TiO2-derived nanotubes were prepared by hydrothermal treatment in 10 M NaOH(aq) by using commercially available TiO2 (Degussa P-25) as starting material. N2-adsorption/desorption analysis, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD) observations of the obtained product revealed the formation of titanate nanotube structure with its diameter of about 10–20 nm. The effect of post-heat-treatment on the phase structure, morphology, specific surface area and photocatalytic activity was investigated. The TiO2 (B) nanotubes could be observed at post-heat-treatment of 300 °C. As post-heat-treatment was increased to 400 °C, the nanotubes began to transform into nanoparticles of anatase phase, producing a bi-crystalline mixture of TiO2 (B) nanotubes and anatase nanoparticles. Moreover, the particles changed into rutile phase through the post-heat-treatment at higher temperatures over 700 °C. The photocatalytic activity of prepared samples was evaluated with photocatalytic H2 evolution. The results showed that the TiO2-derived nanotubes treated at appropriate temperature exhibited high H2 evolution.
757
Chih-Chieh Wang, Chi-Chung Kei, Chih-Liang Wang and Tsong-Pyng Perng
TiO2 nanohoneycomb was fabricated by solution-based nanosphere lithography. TiCl4 solution was used as a precursor to fill in the interspace of the self-assembled polystyrene nanosphere mask. After removing the polystyrene (PS) nanosphere monolayer by heating, an anatase nanohoneycomb was formed. A more uniform nanohoneycomb was obtained by using t-butanol as the solvent for TiCl4 because of its better wetting with the nanospheres. UV–visible spectra of the nanohoneycombs showed that there were two absorption edges at 320 and 470 nm. The photocatalytic activity measurement showed that the nanohoneycomb had a better photodecomposition efficiency than the film.
760
Yoshinori Tokoi, Tsuneo Suzuki, Tadachika Nakayama, Hisayuki Suematsu, Weihua Jiang and Koichi Niihara
Nanosized powders of TiO2 have been synthesized by pulsed wire discharge (PWD) using titanium wire in oxygen gas. The relative energy (R, R = Ei/Ev), which is the ratio of the charged energy of the capacitor (Ei) to the vaporization energy of the wire (Ev), was changed from R = 1.9 to 52.1. The X-ray diffraction patterns of nanosized powders synthesized at various relative energies showed that all the samples had peaks of rutile and anatase. The rutile content increased with the increase in the relative energy, and changed from 6 to 84 vol % at 100 kPa. The median particle diameter decreased from 30.9 to 20.4 nm. Control of the rutile content and particle size was possible by varying the relative energy used for PWD.
764
Hong-Hsin Huang, Hung-Peng Chang, Fang-Hsing Wang, Yuan-Shing Liu, Moo-Chin Wang and Ding-Fwu Lii
NiO/TiO2 films with various NiO film thicknesses ranging from 10 to 320 nm were deposited on silicon and glass substrates by e-beam evaporation at 200 °C, and then annealed in H2 atmosphere at 500 °C for 1 h in order to reduce the NiO film to Ni grains on the TiO2 film. The structures of titanium oxide, NiO, and Ni/TiO2 were determined by X-ray diffraction (XRD) analysis, and the morphology of the Ni/TiO2 films was observed by scanning probe microscopy. The ultraviolet–visible (UV–vis) transmittance and vis absorption of the Ni/TiO2 films were measured by UV–vis spectrophotometry. The results showed that an amorphous titanium oxide was obtained as deposited at 200 °C and that the structure change to the anatase phase after 500 °C annealing. As deposited, crystalline NiO films with XRD patterns similar to that of powder were obtained; however, diffraction peaks of (111) and (200) Ni appeared after annealing in H2 atmosphere. Ni nanograins, coarsened grains, and films were obtained on the TiO2 films when the NiO film with a thickness from 10 to 320 nm was reduced in H2 atmosphere at 500 °C. The transmittance of the Ni/TiO2 films decreased with an increase in Ni particle size. The vis absorption measurement showed that the peak shifted toward a shorter wavelength with a decrease in Ni particle size.
768
Yasuyuki Shimada, Tsutomu Yamada, Jun-ichi Shirakashi and Yasushi Takemura
A local oxidation technique using an atomic force microscope (AFM) was studied. The reaction current passing through the AFM tip was measured in order to evaluate its dependence on the resistivity and surface condition of the samples. The current efficiency actually contributing the oxidation reaction was about 0.5 for a Si substrate. The ratio was constant regardless of the tip scan speed. As for NiFe thin films, the current was higher and the current efficiency was lower than those of the Si substrate. The Al2O3 capped layer on the NiFe thin films reduced the excess current, which did not contribute to the oxidation.
771
Zhifu Liu, Toshinari Yamazaki, Yanbai Shen, Toshio Kikuta and Noriyuki Nakatani
TeO2 nanowires were successfully synthesized by a simple reactive thermal evaporation method using pure Te metal as the source material. The study on synthesis process indicates an optimal synthesis temperature of 400 °C. Structural characterization using X-ray diffraction and transmission electron microscopy shows that the TeO2 nanowires have a single phase tetragonal structure. Scanning electron microscopy observation demonstrates that each TeO2 nanowire starts to grow from a TeO2 nanopartice, which suggests a self-catalytic growth mechanism. The Fourier transform infrared spectrum of TeO2 nanowires shows a blue shift of 20 cm-1 in the axial stretching bands. The gas sensing measurements indicate that TeO2 nanowires have a p-type electrical conduction and can reversibly response to NO2 gas at room temperature.
775
Koji Suwa, Tadachika Nakayama, Tsuneo Suzuki, Hisayuki Suematsu, Weihua Jiang and Koichi Niihara
Ni–Cu nanopowders were successfully synthesized from Cu and Ni wires using pulsed wire discharge. The powders were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), and energy-dispersive X-ray spectroscopy (EDS). XRD confirmed that the nanopowder produced from Ni and Cu stranded wire was of Ni–Cu alloy. The composition of the nanopowders was controlled by varying the ratio of Ni to Cu wire diameter. TEM showed that the size of the prepared particles was less than 100 nm. EDS results revealed that the compositions of single nanoparticles in the nanopowder were different from each other. The composition distribution indicated that most compositions of nanoparticles agreed with that of the stranded wire. Submicron-sized particles consisting of Ni- or Cu-rich compositions were also found in the sample.
780
Hikaru Aoshima, Hiroshi Sakuma and Kiyoshi Ishii
Iron nitride (Fe–N) nanoparticles were prepared by reactive gas flow sputtering. The structure, size distribution, and magnetic properties of these particles were studied as a function of the average atomic ratio of N against Fe (N/Fe ratio). X-ray diffraction analysis revealed that the mixture of α-Fe and γ'-Fe4N was formed at an N/Fe ratio of approximately 0.2 and ε-Fe2–3N began to appear at an N/Fe ratio of approximately 0.4. Using transmission electron microscopy, it was found that α-Fe and γ'-Fe4N crystallites were not formed in one particle; instead, Fe particles and γ'-Fe4N particles coexisted. The size distribution was well fitted by a log–normal distribution; the mean diameter and standard deviation were approximately 50 and 15 nm, respectively, and were independent of the N/Fe ratio. The saturation magnetization decreased monotonously with an increase in the N/Fe ratio.
784
Se-Jun Kim, Hyon-Hee Yoon, Sang-Joon Park, Yong-Seo Park and Hyung-Wook Choi
In this study, nanocrystalline zinc gallate (ZnGa2O4) phosphors were prepared by a precipitation method using aqueous ammonia as the precipitant. This method enabled the low temperature formation of phosphors with spherical shape. The samples were characterized by X-ray diffractometry (XRD), scanning electron microscopy (SEM), and cathodoluminescence (CL). The highest diffraction intensity was observed for the sample with a metal ion concentration of 0.1 mol/dm3. The sample with this metal ion concentration had nanocrystalline ZnGa2O4 phosphor with an average size of about 80 nm. The emission spectra of ZnGa2O4 showed a broad self-activated blue emission band spanning over in the wide range of 300–600 nm with a peak wavelength of about 420 nm; this band showed a maximum intensity at a metal ion concentration of 0.1 mol/dm3.
787
Surawut Chuangchote, Takashi Sagawa and Susumu Yoshikawa
Ultrafine poly[2-methoxy-5-(2'-ethylhexyloxy)-1,4-phenylene-vinylene] (MEH-PPV)/poly(vinyl pyrrolidone) (PVP) composite fibers with the average diameters ranging from 43 nm to 1.7 µm were prepared by electrospinning of blended polymer solutions in mixed solvent of chlorobenzene and methanol. The average diameter of the as-spun fibers was found to decrease into nanometer scale with decreasing the PVP concentration and/or addition of a volatile organic salt, pyridinium formate (PF). PVP was easily removed from MEH-PPV/PVP fibers by the Soxhlet extraction, and after the removal, pure MEH-PPV fibers were obtained as a ribbon-like structure aligned with wrinkled surface in fiber direction. Comparison with the cast film, as-spun fibers showed relatively higher crystallinity, higher conjugation length, and there was a remarkable blue shift of photoluminescence (PL) peak.
794
Tengku Nadzlin Bin Tengku Ibrahim, Kunihiko Tanaka and Hisao Uchiki
Organic films were prepared by RF plasma chemical vapor deposition (CVD) using naphthalene (named naph), propane (prop), and naphthalene mixed propane (naph-prop). All of the samples showed broadband emission of photoluminescence. In IR transmission, aromatic ring out-of-plane C–H bending, C–H stretching, and C=C stretching vibrations were observed in naph-prop sample, and all of the absorption was similar to naph sample. The aliphatic C–Hn stretching vibrations also were founded in all samples. The conductivity of the naph-prop sample was 1.8 ×10-7 S/cm, and this value was large compared to the samples that only prepared by naphthalene or propane. The naph-prop sample showed the space charge limited current (SCLC) at the higher voltage region.
797
Keita Nakagaki, Toshihiko Yamauchi, Yoshinori Kanno and Seiji Kobayashi
A chemical vapor deposition (CVD) system based on 27.12-MHz-RF-heated plasma discharge was developed to investigate the synthesis of advanced ceramics, particularly diamond. In our unique system, a four-turn RF antenna coil was installed inside the chamber. Here, we found for the first time an interesting physical behavior in which capacitively coupled plasma (CCP) suddenly changed to inductively coupled plasma (ICP) at the threshold power. The plasma characteristics, which were measured using a double prove, exhibited Te ∼10 eV and ne ∼1011 cm-3. No impurity was observed, judging from the spectroscopic measurement results. Ball-like diamond on a silicon (Si) substrate was synthesized by the low-power RF heating.
800
Hiroshi Kawabata, Tetsuji Iyama and Hiroto Tachikawa
Hybrid density functional theory (DFT) calculations have been carried out for the lithium adsorbed on a fluorinated graphene surface (F-graphene, C96F24) to elucidate the effect of fluorination of amorphous carbon on the diffusion mechanism of lithium ion. Also, direct molecular orbital–molecular dynamics (MO–MD) calculation [H. Tachikawa and A. Shimizu: J. Phys. Chem. B 109 (2005) 13255] was applied to diffusion processes of the Li+ ion on F-graphene. The B3LYP/LANL2MB calculation showed that the Li+ ion is most stabilized around central position of F-graphene, and the energy was gradually instabilized for the edge region. The direct MO–MD calculations showed that the Li+ ion diffuses on the bulk surface region of F-graphite at 300 K. The nature of the interaction between Li+ and F-graphene was discussed on the basis of theoretical results.
803
Tetsuji Iyama, Hiroshi Kawabata and Hiroto Tachikawa
The electronic states of potassium ion and atom (K+ and K) adsorbed on the amorphous carbon surfaces have been investigated by means of hybrid density functional theory (DFT) calculation to elucidate the nature of interaction between K+/K and the amorphous carbon. Seven graphene sheets (n = 7, 14, 19, 29, 37, 44, and 52, where n means numbers of rings in each carbon cluster) were considered as models of amorphous carbon in the present study. The B3LYP/LANL2MB calculations showed that the potassium ion is located at ca. 2.80 Å from the graphene surfaces and the charge of K+ is not dependent on the cluster size of the graphene sheets. On the other hand, the charge of potassium atom (K) increased with increasing cluster size (n), and it reached a constant value (ca. +0.70) at n = 29–52. Also, direct molecular orbital–molecular dynamics (MO–MD) calculation [H. Tachikawa and A. Shimizu: J. Phys. Chem. B 110 (2006) 20445] was applied to diffusion processes of the K+ ion and K atom on the model surfaces of amorphous carbon. The direct MO–MD calculations showed that the K+ ion and K atom diffuse freely on the surface at 800 K. The nature of the interaction between K+/K and the carbon clusters was discussed on the basis of theoretical results.