305
Hajime Kitagawa and Hiroshi Nakashima
Deep levels in nickel-doped n- and p-type silicon have been studied by the Hall effect and deep level transient spectroscopy (DLTS) under various diffusion and isothermal annealing conditions. It was found that nickel introduces an acceptor level of 0.47±0.04 eV from the conduction band and a donor level of 0.18±0.02 eV from the valence band, and that the concentrations of the two levels are practically identical. Isothermal annealing experiments have revealed stable behaviors of the two levels. The results suggest that the two levels are different charge states of the same substitutional nickel atoms in silicon.
311
Woo-Yeol Kim, Akio Shibata, Yoshiyuki Kazama, Makoto Konagai and Kiyoshi Takahashi
We have optimized the preparation conditions of p-i-n type a-Si:H solar cells prepared by photo-CVD. The pyramid-shaped SnO2 with haze ratio of 25% was chosen as the best TCO (transparent conductive oxide). The best efficiency obtained for a glass/TCO/p/buffer/i/n/Al structure of this type was 11.4% (Voc=0.90 V, Isc=17.86 mA/cm2, FF=0.706) for a 3×3 mm2 cell; the thicknesses of the p-, buffer-, i-, and n-layers were 50 A, 150 A, 7800 A, and 600 A, respectively.
316
Yohichi Kataoka, Yuuhiro Hida, Hiromu Ueba and Chiei Tatsuyama
Electrical properties of epitaxial Ge films grown on Si(100)–2×1 surfaces have been studied by Hall measurement, and their structural properties have been characterized by analyses of LEED patterns, X-ray diffraction, Raman scattering spectra and cross-sectional TEM images. It has been found that the growth layers exhibit p-type conduction, possibly due to the Ge vacancies and the temperature dependences of carrier concentration n(T) and hole mobility µ(T) depend on growth conditions, such as substrate temperature, film thickness and annealing treatment. For thick Ge films grown on coalesced Ge islands, µ(T) is governed by long-range optical phonon scattering, indicating the growth of high structural quality in the Ge films. For relatively thin films composed of Ge islands, on the other hand, µ(T) obeys short-range acoustic phonon scattering due to crystalline imperfections, such as dislocations or defects. Similar experiments have also been performed for thin Ge films grown on predeposited Ge buffer layers on Si substrates.
324
Shigetoshi Ohshima, Hiroyuki Ishida and Tokuo Wakiyama
Ba–Ln–Cu–O compounds (Ln=Gd, Dy, Ho and Er) were prepared by a solid-state reaction. The optimum sintering temperature for obtaining a single phase of Ba2LnCu3O7-δ was different for each Ln element, and this temperature decreased with increasing atomic number of Ln. A single phase with the perovskite structure was obtained only around the Ba2LnCu3O7-δ composition. Tc's of these compounds prepared by a solid-state reaction in air increased with increasing atomic number of Ln. Tc's of samples prepared in oxygen atmosphere were almost the same. The magnetic moment of Ba1-xLnxCuO3-y compounds is associated with each Ln, and its value is in good agreement with the Ln3+ Hund rules free ion values.
330
Masaki Sato, Takashi Kamimura and Takao Iwata
The nonlinear magnetic response of a high-Tc superconductor YBa2Cu3O7-x has been investigated by the ac induction method. At temperatures below 80 K, the fundamental and the third-higher harmonic susceptibility components of both the pellet and coarse powder samples strongly depends on the field amplitude. Also, M-H curves exhibit a hysteresis which bears a similarity to that of hysteretic superconductors. These characteristics are absent in well-isolated particles. Around the transition temperature, susceptibility components have a behavior distinct from that at low temperature and the magnetic response is nearly reversible. The observed magnetic behavior is interpreted as a superposition of the bulk property and the effect of weak linkage of superconducting particles.
334
Ryoji Sugise and Hideo Ihara
The Tl–Ba–Ca–Cu–O compounds, TlBa2Can-1CunOy (n = 1–5), with a single Tl–O layer and multiple Cu–O layers per unit cell were prepared. The formation process of these phases was studied. The numbers of Cu–O and Tl–O layers were influenced by the thallium content. Control of the thallium content was essential to prepare the desired phases in the Tl–Ba–Ca–Cu–O system. The value of Tc increased with increasing number of Cu–O layers (1≤n ≤4). At n=5 Tc was lower than that at n =4. Therefore, the highest Tc value was obtained at n=4.
341
Tokuko Sugai, Gin-ichiro Oya and Syozo Imai
We studied the decarbonation process of a ternary mixture of Y2O3, BaCO3 and CuO or Cu2O by TG-DTA analysis to clarify the optimum condition for the preparation of YBa2Cu3O7-y ceramics, which are superconducting above 90 K. We found that a narrow temperature region, 940∼950°C, is desirable for the decarbonation process. Furthermore, we observed an anomaly at ∼600°C in DTA curves of stoichiometric YBa2Cu3O7-y ceramics and nonstoichiometric Y–Ba–Cu–O samples. From the strong correlation between the magnitude of this anomaly and the composition of the ceramics, the anomaly was attributed to the orthorhombic-tetragonal phase transition in the YBa2Cu3O7-y phase. It was also found that the composition dependence of Tc of the ceramics correlates strongly with that of the magnitude of the anomaly.
346
Michio Watamori, Kenjiro Oura, Fumiya Shoji, Tsutomu Yotsuya, Soichi Ogawa and Teruo Hanawa
The composition and crystalline structure of high-Tc superconducting YBa2Cu3Ox thin films formed on MgO(100) and Si(100) substrates have been investigated by Rutherford backscattering and channeling techniques. Y, Ba, Cu contents have been analyzed by employing a high-energy (over 4.5 MeV) 4He ions and large scattering angle (near 170°) condition, where Y, Ba and Cu peaks are clearly separated from each other. Oxygen concentration has been obtained through the use of low primary energy (below 2.5 MeV) and small scattering angle (below 150°) conditions, where the O peak is separated from the background. The crystalline quality of the films has also been investigated by ion channeling techniques.
351
Hiroaki Myoren, Yukio Nishiyama, Hirofumi Fukumoto, Hiroyuki Nasu and Yukio Osaka
High-Tc superconducting Ba2YCu3Ox thin films have been epitaxially grown on Si(100) substrates with the epitaxially grown tetragonal ZrO2 or cubic yttria-stabilized zirconia (YSZ) as a buffer layer. The thin films were prepared by rf magnetron sputtering of the stoichiometric Ba2YCu3Ox target below 700°C. An adequate positive substrate bias was necessary to ensure surface smoothness and to show the superconducting transition above liquid nitrogen temperature without any post-treatment. The highest Tc(onset) and Tc(end) observed were 88 K and 84 K, respectively.
356
Teruo Matsushita, Naoyuki Harada, Kaoru Yamafuji and Minoru Noda
The hysteresis losses due to ac magnetic fields are measured for a bulk superconducting Nb-Ta tape in the regime of reversible fluxoid motion under a bias field. The observed hysteresis losses and power factor agree well with the theoretical estimate based on Campbell's model of the force-displacement characteristic of the fluxoids. The hysteresis losses in superconducting multifilamentary wires with very fine filaments are also estimated from this scheme.
361
Kenji Sumiyama, Koichi Takemura, Noriyuki Kataoka and Yoji Nakamura
Magnetization and Mössbauer effect measurements were made for Fe1-xCux alloys sputter-deposited on water-cooled substrates under Ar gas pressures, PAr, of 8.9 and 0.23 Pa. The scanning electron micrograph (SEM) shows a columnar structure for PAr=8.9 Pa and a fibrous structure for PAr = 0.23 Pa. A perpendicular magnetic anisotropy is observed and the coercive force, Hc, is large for PAr = 8.9 Pa, while an in-plane magnetic anisotropy is observed and Hc is small for PAr =0.23 Pa. The magnetization and average hyperfine field for PAr = 8.9 Pa are smaller than those for PAr = 0.23 Pa. These differences can be ascribed to the presence of CuFeO2, which is detected in the paramagnetic Mössbauer spectra in the Cu rich alloys formed under PAr = 8.9 Pa.
368
Ryoichi Nakatani, Toshio Kobayashi, Shigekazu Ootomo and Noriyuki Kumasaka
Fe–2 at.%Ni/Ni–20 at.%Fe multilayered films are formed by the ion beam sputtering method. Their magnetic properties and magnetic anisotropy dispersions are examined. The Fe–Ni/Ni–Fe multilayered film of a 25 nm period displays a relative permeability of 1300 and a saturation magnetic flux density of 1.9 T. As the period of Fe–Ni/Ni–Fe multilayered films is reduced, the Fe–Ni crystallite size and the magnetic anisotropy dispersion become smaller, resulting in good soft magnetic properties.
372
Haruko Masuya and Haruo Awano
The compositionally segregated microstructure and the crystal structure of sputter-deposited Co–Cr films to which various percentages of carbon were added are studied by transmission electron microscopy. The results are as follows:
(1) The degree of segregation in the microstructure increases as amount of carbon added increases. The segregated pattern is changed by the amount of carbon added.
(2) The saturation magnetization increases as the degree of the segregation increases. The perpendicular coercivity depends on the perpendicular magnetic anisotropy, and magnetic anisotropy is related to the degree of segregation and the refinement of the segregated pattern.
(3) The plane defects perpendicular to the C-axis in sputter-deposited Co–Cr films are grown by carbon addition.
379
Takakazu Takahashi, Masaaki Yoneda and Masahiko Naoe
Amorphous CoZrNb films with high saturation magnetization 4πMs of about 14 kG and low coercivity Hc of about 0.3 Oe have been successfully prepared by the CMF magnetron sputtering technique with a CoZrNb alloy target. Hc and 4πMs along the easy axis were changed by background pressure, film thickness and Ar pressure Pr. The applied voltage of discharge operation is as low as 270 V at Pr of 0.3 Pa. The maximum deposition rate is as large as 0.13 µm/min for a power density of 4.42 W/cm2. The target utilization efficiencies are improved in spite of using a magnetic target because a leakage magnetic field increases more to a greater extent by attaching an outer pole piece. These are about 95% and 60% in surface area and in volume, respectively. The changes in a film thickness of 1 µm deposited on the substrate were 0.05 µm at Pr of 0.2 Pa, and 0.06 µm at a distance of 50 mm between substrate and target, respectively.
384
Akihiko Nishida, Kazumi Horai and Tetsuo Fujita
Changes induced by oxygen implantation in the temperature dependence of the linewidth, g value and peak height of CESR in aluminum foils were investigated, using the spin transmission technique. It was found that oxygen implantation induces excess conduction-electron-spin relaxation, which takes maxima at 7 K and 77 K. The results were analyzed by Hasegawa's model incorporating the Kondo effect. The excess relaxation was simulated fairly well by “resonant Kondo scattering” with two kinds of impurity states. Both the g value and peak height revealed a large contribution to interzone scattering at the Fermi surface from complex localized surface states. Based on detailed observations, the existence and contribution of localized moments at the Al/AI2O3 interfaces with oxygen implantation are suggested.
391
Takahiro Matsumoto, Motoyoshi Baba, Takahiro Kuga and Masahiro Matsuoka
We have achieved reduction of the power fluctuation of the second harmonic of a cw mode-locked YAG laser from 5% to less than 0.1% using a feedback loop with an acoustic loss modulator inside the laser cavity. By using the second harmonic of this laser as a pumping source, we have also reduced the output power fluctuation of a synchronously pumped dye laser at low frequencies.
396
Eiichi Tsuchida and Heihachi Sato
Taking into account the radial distributions of the gas-flow velocity v, the discharge current Idis, the gas temperature T and the effective pumping rate ηe, we theoretically derive the gain coefficient γ as a function of the radial distance from the plasma-tube axis for a fast-axial flow (FAF) CO2 laser amplifier. For various combinations of v and Idis, the calculated γ's are compared with the experimental results corresponding to both laminar and turbulent flows, resulting in good agreement in both cases. Increase of v leads to a linear enhancement of γ: for example, γ becomes about two times larger with increasing v from 80 to 180 m/s, while there is an optimum current near 45 mA to provide the highest gain in our FAF system. It is especially noteworthy that the high-gain region tends to spread towards an area far off-center of the discharge tube axis with increasing v, and its spreading area becomes significantly broader at a turbulent flow greater than v = 170 m/s.
406
Shinji Okamoto, Eiichiro Nakazawa and Yuzuru Tsuchiya
Thin electroluminescent SrS films activated with Nd3+, Sm3+, Dy3+, Ho3+, and Er3+ ions have been investigated. Their emission colors are found to be orange-white, orange, yellow, greenish white and green respectively, originating from transitions within the 4fn configuration of the rare-earth ions. The luminance levels of these devices are all over 200 cd/m2, except for that of SrS:Ho3+ (110 cd/m2), on the application of a driving voltage in the range 70–100 V with a frequency in the range 3 k–5 kHz. The main spectral regions of these spectra are found to shift to shorter wavelengths in comparison with those of the same ions in ZnS-based TFEL devices.
410
Takashi Matsumoto, Takamasa Kato, Minoru Takiguchi and Tetsuro Ishida
Deep level transient spectroscopy (DLTS) measurement has been made on solution-grown Te-doped In1-xGaxP alloys with 0.12 ≤ x ≤0.96. Three main electron traps, SGE1, SGE2 and SGE3, were detected. Their activation energy of carrier emission, ET, were about 0.17, 0.40 and 0.45∼0.60 eV, respectively. SGE1 was detected in samples with x \lesssim 0.83, SGE2 in samples with x \gtrsim0.56 and SGE3 was detected in all samples examined. The peak of the DLTS spectrum of SGE2 moves to lower temperatures as the filling pulse width, tp, is increased; and ET derived from the Arrhenius plot depends on tp.
418
Nobuo Saito and Kazuo Ikezaki
Surface potential and thermally stimulated currents (TSC) were examined for negatively corona-charged spherulitic polypropylene (PP) which was isothermally crystallized at 140°C for 2 or 4 hours from the 190°C melt of PP. It was found that the surface potential of the 4 hours-crystallized PP containing many large spherulites was limited to below about -900 volts. However, untreated PP and the 2 hours-crystallized spherulitic PP showed no surface potential saturation up to -1800 volts, which is the limit of the charging apparatus used in this study. From the results on the TSC of these samples, their surface potential saturation can be explained in terms of decrease in the number of charge trapping sites which are located in the interspherulitic amorphous regions of these samples. It was also demonstrated that the internal structure of spherulites did not contribute significantly to the charging saturation of spherulitic PP.
423
Tetsuroh Tokoro, Masayuki Nagao and Masamitsu Kosaki
The high-field dielectric dissipation factor (tan
δ) of low-density polyethylene (LDPE) films was studied as a function of the applied ac field and the voltage application period. The measurements were made at room temperature by means of a current comparator-type capacitance bridge. As the applied ac field increased, the high-field tan
δ increased gradually. With the voltage application period, the high-field tan
δ first increased and then decreased, exhibiting a peak. This time variation of tan
δ was accelerated with increase in the applied electric field. These characteristics of the high-field tan
δ in LDPE films are discussed on the bases of the carrier generation in the bulk due to the modified Poole-Frenkel effect, the carrier injection from the electrodes, the trapping of the carriers and the formation of the space charge layer in front of the electrodes.
429
J. J Wu and Shu-Hsia Chen
This paper reports on the observation of electric bistability and a first-order electric Freedericksz transition induced by an optical field in a homeotropic nematic liquid crystal film. Molecular reorientation as a function of electric field is characterized by an unambiguous hysteresis loop which exhibits electric bistability. The experimental results match the numerical/theoretical results fairly well. The tricritical point will also be discussed.
434
Maeko Kakizaki, Morimasa Tanimoto and Teruo Hideshima
In order to determine the characteristics of the glassy-state relaxations of poly(bisphenol-A carbonate) which are closely overlapping each other, shear relaxation modulus was measured from 10 sec to 900 sec at temperatures ranging from ca. -180°C to 0°C. Three relaxations named β, γ and δ in the order of descending temperature were observed separately and master curves were determined by the method of reduced variables. The activation energies of the β, γ and δ relaxations were estimated to be ca. 30, 25 and 9 kcal/mol, respectively. Theoretical considerations suggest that the molecular motions for the β, γ and δ relaxations are the local-mode motion of main chain, the flip motion of a phenylene with a carbonate group, and the rotational motion of a pair of methyl groups belonging to neighboring chains and coupled by van der Waals force.
440
Yoshiyuki Suzuki and Tatau Nishinaga
A single crystal Si layer was grown over SiO2 film by epitaxial lateral overgrowth (ELO) using LPE, and the dependence of the ratio of the lateral to the vertical growth rates on crystal orientation was investigated. Sn was used as a solution, and it was found that the growth surface was flat and completely mirror like. The lateral growth had a singularity when the line seed was aligned in just the <110 > orientation, but it was almost constant when the orientation was varied around the <112 > orientation. The time dependence of the growth was investigated, and it was found that both the lateral width and the vertical thickness were approximately proportional to t1/2, and the volume of the growth was proportional to t0.9. Sirtl etch revealed that almost no etch pits were observable on the ELO layer. This result shows that ELO by LPE yields SOI films with an extremely good crystal quality.
446
Muneo Nagasaka
Tensile experiments have been carried out over a wide range of temperatures on single crystals of high-purity white tin with low dislocation density. From the observations of slip lines it is found that different slip systems are activated for different temperature regions and for different orientations of specimens. By deformation with the (100)[010] slip system the cell structure is formed in the specimen. The critical-resolved shear stress of this system shows a similar temperature dependence to that of cubic metals. In the case of the (1
0)½[111] slip system, only isolated dislocations are formed during deformation and the yield point phenomenon occurs. The critical-resolved shear stress of this system shows a strong temperature dependence not found in cubic metals. It increases nearly exponentially with decreasing temperature and attains a factor of 200.
453
Yoshiaki Uesu, Katsutoshi Yamane and Boris A. Strukov
Temperature dependence of the optical second-harmonic intensity of ammonium fluoroberyllate crystal (NH4)2BeF4 in the incommensurate and ferroelectric phases, and temperature dependence of coherence lengths in the ferroelectric phase were precisely measured. Strong second-harmonic intensity was not observed in the incommensurate phase, contrary to a previous report on the same type of crystal. Measured coherence lengths were compared with the incommensurate modulation period determined by the X-ray diffraction method. It was found that the coherence lengths were larger than the modulation period by a factor of 103. These facts indicate that the possibility of quasi-phase matching, i.e. the coincidence of the coherence length and the modulation period, is excluded in the crystal.
457
Masami Morooka and Masayuki Yoshida
In the basic partial differential equations for diffusion of gold in dissociative and kick-out mechanisms, substitutional gold, interstitial gold, vacancies and self-interstitials are taken into consideration. It takes a long time to solve these equations numerically. It is therefore convenient to solve the approximate partial differential equation for substitutional gold, which is obtained after the reactions between these four elements have reached their local equilibrium states and the interstitial gold has reached its thermal equilibrium state, under suitable boundary and initial conditions.
In the in-diffusion process, the conditions of the approximate equation are different from those of the basic equations. In the annealing process, the conditions are the same for the basic and the approximate equations.
464
Yoji Tokumitsu, Akira Kawabuchi, Haruyuki Kitayama, Takeshi Imura and Yukio Osaka
Cadmium telluride is deposited by rf sputtering on the clean surface of GaAs(100) substrates from which the surface native oxides have been etched off in advance by H2 plasma treatment. RHEED patterns of CdTe films prepared at 270°C on GaAs pretreated with H2 plasma at 120°C are streaked with (100) characteristics, which shows that the deposited layers are grown epitaxially. The crystalline quality of the CdTe films, which depends on the substrate temperature, is evaluated by means of the optical reflectance. The peak height of the second-derivative reflectance spectra, which is a measure of the crystalline quality, steeply increases at deposition temperatures of 220∼270°C. Thus a deposition temperatures of more than 270°C is needed for high crystalline quality.
468
Yutaka Shimotori, Meiso Yokoyama, Shigetoshi Harada, Katsumi Masugata and Kiyoshi Yatsui
Electroluminescent ZnS:Mn thin films have been guickly deposited by a high-density, high-temperature plasma produced by the irradiation of an intense (>GW/cm2), pulsed (∼tens of ns) ion beam onto a ZnS:Mn target. The films prepared on a glass substrate have a polycrystalline hexagonal structure. The temperature of the target plasma was estimated to be ∼2.7 eV, where the plasma was highly ionized. The instantaneous deposition rate was estimated to be ∼4 cm/s, which is at least five orders of magnitude higher than that of any other conventional evaporation techique. We have prepared a ZnS:Mn electroluminescent device with a luminescent layer having a thickness of ∼200 nm. The device has a threshold voltage of ∼80 V0p (zero to peak value). The maximum luminance of 195 cd/m2 has been obtained under 10 kHz sinusoidal excitation at 144 V0p.
473
Masamoto Tanaka, Wataru Mizutani, Tsuneo Nakashizu, Shuichi Yamazaki, Hiroshi Tokumoto, Hiroshi Bando, Masatoshi Ono and Koji Kajimura
An investigation of charge-density waves in 4Hb–TaS2 was carried out by scanning tunneling microscopy and scanning tunneling spectroscopy. We succeeded in discriminating of the surface electronic structures of 4Hb–TaS2, octahedral structure and trigonal-prismatic structure in terms of the electronic properties. The measured energy gap of the charge-density waves of 4Hb–TaS2 at room temperature was about 9± 10 meV.
477
Ikurou Umezu, Tsutomu Ogawa and Toshihiro Arai
Temperature dependence of absorption, photoacoustic(PA), photoluminescence excitation(PLE) and photoluminescence(PL) spectra were measured for filter glasses which include sulfur-rich CdSxSe1-x microcrystals. Absolute quantum efficiency for radiative recombination was obtained by comparing photoacoustic spectra with photoluminescence spectra. Quantum efficiency of radiative recombination for small microcrystals is found to be higher than that for large microcrystals. By solving the rate equations, very small band-to-band nonradiative transition was suggested in these microcrystals. We regarded this as the main reason for the large quantum efficiency.
484
Toshihiro Arai, Hidehiko Fujumura, Ikuro Umezu, Tsutomu Ogawa and Americo Fujii
Change in the electronic state due to size confinement was studied for the CdS cluster embedded in GeO2 glass by photoacoustic, optical absorption and photoluminescence spectroscopies. The cluster size increases with increasing annealing temperature and time. The activation energy of ion diffusion during cluster growth is 0.45 eV. When the cluster size becomes less than about twice the exciton size, the energy bands become discrete. The energies of 1st and 2nd excited states increase with decreasing cluster size. The size dependence of the ist excited state determined experimentally coincides with the calculation. The energy of the surface state also shifts in parallel with the shift of the 1st excited state. When the cluster size decreases, the intensity of the edge emission decreases faster than that of the surface emission.
490
Shigehiko Yamamoto, Isato Watanabe, Sadanori Taguchi, Susumu Sasaki and Tomio Yaguchi
The electron emission of a Sc-type impregnated cathode is known to be enhanced by a monoatomic-order surface layer composed of Ba, Sc, and O. This layer reduces the work function much lower than those of conventional impregnated cathodes.1,2) It also makes the cathode resistant to gas contamination.3) In the present work, a basic impregnated cathode is coated with a thin tungsten film containing a certain amount of Sc2W3O12 (about 5–10 atomic percent) to produce a (W-Sc2W3O12) coated cathode.
The supplying mechanism of free Sc atoms, and hence the monoatomic-order layer formation mechanism,4) is clarified by Auger electron analysis and X-ray diffraction analyses. Free Sc atoms are produced through the following surface chemical reaction between Sc2W3O12 and Ba atoms supplied from the substrate4) as
Sc2W3O12+3Ba=3BaWO4+2Sc.
This monoatomic layer formation improves the electron emission current density measured at 850°Cb (brightness temperature) about threefold compared to that of conventional Os coated impregnated cathodes.
495
Katsumi Ishikawa, Takashi Kishida, Masahiro Kuze, Fuminori Sai, Toru Tsuboyama, Sukeyasu S. Yamamoto, Takashi Maki and Shoji Suzuki
A fine pressure control system utilizing a commercially available simple and inexpensive light intensity control circuit kit for a liquid deuterium target is described. The difference between the liquid deuterium vapor pressure and the atmospheric pressure can be controlled to much better than 0.001 kg/cm2 or equivalently the liquid deuterium density can be kept constant at 0.1626±0.0003 g/cm3.
498
Takahide Nakagawa and Keiko Yuasa-Nakagawa
The time resolution of a time-of-flight (T.O.F.) detector which consists of a channel plate detector (CPD) with a central hole and a surface barrier detector (SBD) was measured. A time resolution of 80 psec fwhm was obtained for 8.78 MeV alpha particles. The influence on fast timing of the SBD of alpha particles was carefully studied. The plasma delay time and time resolution of the SBD were found to strongly depend on the electric field strength and properties of the SBD.
501
Kanehiro Nobata and Masaaki Kurokawa
The dynamic properties of an arc discharge have been experimentally studied. The arc transition occurs even with a small voltage between two electrodes to form a new arc path which is made by the advance of electrons from the cathode to the anode. And a reignition voltage against a residual current is obtained. That reignition occurs in two different forms. One directly develops to an arc discharge and the other develops through the formation of a glow discharge. Furthermore, we have discussed a condition on which the reignition occurs in a very short time.
507
Hiroyuki Daido, Katsunobu Nishihara, Kunioki Mima, Masanobu Yamanaka, Takuma Endo, Hiroyuki Shiraga, Yoshiaki Kato, Eisuke Miura, Yoneyoshi Kitagawa, Chiyoe Yamanaka et al
We report the generation of long-life plasmas confined by the heavy shell surrounding a plasma produced by lasers. We also demonstrate the neutron production from shell-confined carbon-deuterium plasmas using a GEKKO XII glass laser system at 1.05 µm and 0.53 µm wavelengths. A maximum neutron yield of more than 108 per shot without an implosion was obtained. Analyzing these results with the hydrodynamic simulation code, we propose the required conditions for demonstrating magnetic thermal insulation observed by the neutron measurement.
512
Keizo Kato, Akihiro Kunishima and Kazuo Minami
Large amplitude cavitons caused by incident high-power microwave pulses with a frequency of 2.85 GHz up to 100 kW at the resonance plane are observed in a TM01 cylindrical plasma waveguide. The localized RF electrostatic fields are found to be attenuated by the action of wave breaking, and the dips of the density continue to grow. The dependences of the density profile of cavitons, the wave breaking time and the localized RE electrostatic fields at the breaking time on the incident power are consistent with the theoretical prediction, even for such high powers. The characteristics of Langmuir probe measurements after the initiation of the incidence of microwave pulses are also described.
518
Johann Georg Rabe, Gerlinde Bischoff and Werner F. Schmidt
Chemically prepared polypyrrole films were exposed to vapors of sulfur dioxide, methyl amine, ammonia, and water. The resulting increase in electrical conductivity was measured as a function of the partial pressure. The results are discussed on the basis of the modification of the polymer surface layer by adsorption of molecules and subsequent electron transfer.
524
Norio Yamamoto, Yuichiro Yamada, Kahoru Mori, Hiroshi Orihara and Yoshihiro Ishibashi
To obtain zig-zag defect-free liquid crystal cells by means of a standard rubbing technique, the effect of a new polyimide film on pretilt angle at a surface has been investigated. This new polyimide imposes the high pretilt over wide rubbing density, and good orientation of liquid crystals without zig-zag defects can be obtained for rubbing densities higher than 0.5×103. A new driving scheme to realize display devices with a high contrast ratio is proposed. This scheme is devised by utilizing anomalous switching behavior and AC-stabilized effect. The prototype of the ferroelectric liquid crystal display device shows the maximum contrast ratio of 40:1.
530
Hideki Yayama, Akihisa Tomokiyo and Kazuyoshi Hirakawa
Electrolyses by a TiMn1.5Hx electrode in alkaline aqueous solution were carried out at various temperatures under constant-current and constant-potential conditions. The electrode resistance increased with decreasing temperature. The activation energies for the charge transfer process and for the diffusion of hydrogen were obtained. The increase in electrode resistance with decreasing temperature was attributed largely to the temperature dependence of the charge transfer rate rather than to that of the diffusion rate of hydrogen.
535
Seizo Morita, Takao Okada and Nobuo Mikoshiba
We investigated the in situ STM images sequentially at the same places of Ag and Au electrodes in a 0.1 M KCl solution, as a function of a potentiostatic voltage. For the Ag electrode, by decreasing the potential, we found that the surface corrugation of the electrode varies suddenly from a flat to a rough surface around the calculated equilibrium potential of AgCl formation/reduction processes. We also found another phenomenon whereby the surface of the Ag electrode becomes more and more smooth with decreasing potential. We supposed this phenomenon to be a rearrangement of the Ag surface caused by the desorption of Cl- specific adions from the active sites. We also found that the roughness of Au surface depends on the potentiostatic voltage. This result seems to be related with the anodic dissolution/reduction processes and the desorption of Cl- specific adions.
541
Toshio Kasuga, Hiroto Yonehara, Masami Hasumoto and Toshio Kinoshita
An increase in impurity was observed in the single bunch mode of the UVSOR storage ring. Electrons in RF buckets following the single bunch increase with time after the electron beam injection. This phenomenon is caused by electrons thrown out of the bucket by the Touschek effect being captured again by following buckets due to radiation damping. The qualitative explanation is satisfactory and the quantitative estimation of the rate of the impurity increase is reasonable.
545
Fumiya Shoji, Hideki Taniguchi, Osamu Kusumoto, Kenjiro Oura, Teruo Hanawa, Yoshihiko Suzuki and Soichi Ogawa
Co–Cr films prepared by the method of argon ion beam sputtering are analyzed by the proton-induced X-ray emission (PIXE) technique. The PIXE spectra show a clear peak of Ar Kα X-ray, indicating the existence of impurities. The content of argon impurity is in the order of 102 ng, and the content is found to increase as the argon ion beam energy increases and the argon pressure decreases. The argon impurity is attributed to the scattering processes of argon ions at the Co–Cr alloy target surface.
549
Masayuki Endo, Masaru Sasago, Kouji Matsuoka and Noboru Nomura
Contrast enhancement by alkaline surface treatment of dyed photoresist is characterized. A surface-modified layer formed by the alkaline surface treatment prevents unexposed areas of the resist from being dissolved and acts as a barrier during development. Utilizing alkaline surface treatment, high-aspect-ratio submicron patterns on a highly reflective substrate are successfully delineated with negligible resist thickness loss. It is found that this modified process is enhanced by baking before exposure.
553
Masahiko Morita, Kikuo Kobayashi, Takeo Suzuki and Yoshimichi Okano
The photoluminescence (PL) of Be-doped AlxGa1-xAs grown by MBE for Al contents 0.20<x<0.88 and hole concentrations 5×1018<Nh< 1.5×1019 cm-3 has been measured at 77 K. PL spectra for higher x's suggest the presence of deep levels. The formation of deep levels associated with interstitial Be is discussed.
555
Haruki Yokoyama, Masaki Okamoto, Tsutomu Hamada, Takeshi Imura, Yukio Osaka, Akiyoshi Chayahara and Masami Fujisawa
The optical reflectance of cubic boron nitride (c-BN) was measured for sintered and microcrystalline samples at room temperature in the photon energy range 5–25 eV. Kramers-Kronig analysis was performed to determine the real ε1 and imaginary ε2 parts of the dielectric function. The spectrum of ε2 for sintered c-BN shows peaks at 9.05 eV and 11.7 eV and shoulders at 10 eV, 13.2 eV and 16.7 eV. This spectrum was compared with the one theoretically obtained by Tsay et al. and assignment of the structure was made. The ε2 for microcrystalline c-BN has a broad structure with a peak at 11.7 eV.
557
Hiroyuki Nasu, Chikashi Akamatsu, Ryo Hayashi and Yukio Osaka
Differential scanning calorimetry (DSC) studies of P-doped hydrogenated amorphous silicon (a-Si:H) show characteristic behaviors of the relaxation phenomena related to the defect frozen states. The equilibration temperature TE* detected by DSC agrees well with TE determined by the temperature dependence of dc conductivity. The exothermic reaction detected by DSC is semiquantitatively interpreted by the theoretical model of the equilibrium process of defects.
559
Qin-Sheng Zhu, Kazumasa Hiramatsu, Nobuhiko Sawaki and Isamu Akasaki
The electron trap concentration and its in-depth profile have been investigated on InxGa1-xAsyP1-y/(100)GaAs Schottky diodes by the DLTS technique. An electron trap thought to originate from an anion vacancy took a maximum value in concentration as the As fraction reached the middle of the immiscibility region. Because of the relatively low binding energy of the alloy atoms near the middle of the immiscibility region, a large number of anion vacancies are created there. In addition, the influence of the defects in a substrate was considered to explain the higher electron trap concentration near the heterointerface.
561
Katsunori Muraoka, Kiyoyuki Suenaga, Kenji Morita, Yukihiko Yamagata, Hee Je Kim, Chikahisa Honda, Mitsuo Maeda and Masanori Akazaki
The surface binding energy of nickel was estimated from the measured velocity-distribution function of sputtered nickel atoms by rapid-frequency-scan laser spectroscopy, yielding 1.2±0.5 eV, which was about one third of the sublimation energy of nickel. The results were interpreted as the formation at the surface of a carbide phase which weakened the binding of atoms, compared with that in pure nickel.
563
Kiyoshi Hayase
The magnetohydrodynamic equilibrium of a moderately elongated screw pinch is considered. From comparisons of experimental and calculated data on the elongation factor and radial shift of the plasma column, the configuration is described by a two-region flat-current tokamak model. The inner high-beta plasma is surrounded by a force-free current region.
565
Yukihiko Yamagata, Kiyoyuki Suenaga, Katsunori Muraoka, Mitsuo Maeda and Masanori Akazaki
Optogalvanic signals, caused by laser-excited Rydberg atoms, were measured to estimate the electric field in a DC glow discharge in helium. With a careful analysis of the various factors limiting the detection limit and an experiment to check the analysis, the detection limit of an electric field of 21.5 V/mm was obtained which was limited by the laser spectral width.
567
Shin'ichiro Okude
A small-distortion and low-cost Stark modulator is developed by newly adopting class-AB amplification in a trasformer-coupled voltage amplifier. Through analysis of the operation, clear guidelines for the design and tuning of the Stark modulator are found. The circuit paramenters for operations of output voltages 3 kV and 800 V (peak-to-peak) at 100 kHz and 2 MHz, respectively, are shown.