The potential of bulk melt-processed YBCO single domains to trap significant magnetic
fields (Tomita and Murakami 2003 Nature 421 517–20; Fuchs et al 2000 Appl. Phys. Lett.76
2107–9) at cryogenic temperatures makes them particularly attractive for a variety of
engineering applications including superconducting magnets, magnetic bearings and
motors (Coombs et al 1999 IEEE Trans. Appl. Supercond.9 968–71; Coombs et al 2005
IEEE Trans. Appl. Supercond.15 2312–5). It has already been shown that large fields can be
obtained in single domain samples at 77 K. A range of possible applications exist in the
design of high power density electric motors (Jiang et al 2006 Supercond. Sci. Technol.19 1164–8). Before such devices can be created a major problem needs to be
overcome. Even though all of these devices use a superconductor in the role of a
permanent magnet and even though the superconductor can trap potentially huge
magnetic fields (greater than 10 T) the problem is how to induce the magnetic
fields. There are four possible known methods: (1) cooling in field; (2) zero field
cooling, followed by slowly applied field; (3) pulse magnetization; (4) flux pumping.
Any of these methods could be used to magnetize the superconductor and this may be
done either in situ or ex situ.
Ideally the superconductors are magnetized in situ. There are several reasons for this: first,
if the superconductors should become demagnetized through (i) flux creep, (ii)
repeatedly applied perpendicular fields (Vanderbemden et al 2007 Phys. Rev. B 75
(17)) or (iii) by loss of cooling then they may be re-magnetized without the need
to disassemble the machine; secondly, there are difficulties with handling very
strongly magnetized material at cryogenic temperatures when assembling the
machine; thirdly, ex situ methods would require the machine to be assembled
both cold and pre-magnetized and would offer significant design difficulties. Until
room temperature superconductors can be prepared, the most efficient design of
machine will therefore be one in which an in situ magnetizing fixture is included.
The first three methods all require a solenoid which can be switched on and off. In the first
method an applied magnetic field is required equal to the required magnetic field,
whilst the second and third approaches require fields at least two times greater.
The final method, however, offers significant advantages since it achieves the
final required field by repeated applications of a small field and can utilize a
permanent magnet (Coombs 2007 British Patent GB2431519 granted 2007-09-26).
If we wish to pulse a field using, say, a 10 T magnet to magnetize a
30 mm × 10 mm
sample then we can work out how big the solenoid needs to be. If it were
possible to wind an appropriate coil using YBCO tape then, assuming an
Ic of 70 A and a
thickness of 100 µm, we would have 100 turns and 7000 A turns. This would produce a
B field of
approximately 7000/(20 × 10−3) × 4π × 10−7 = 0.4 T. To produce 10 T would require pulsing to 1400 A! An alternative calculation would be to assume a
Jc of say
5 × 108A m−1 and a coil
1 cm2 in cross section. The
field would then be 5 × 108 × 10−2 × (2 × 4π × 10−7) = 10 T. Clearly if the magnetization fixture is not to occupy more room than the puck itself
then a very high activation current would be required and either constraint makes in situ
magnetization a very difficult proposition.
What is required for in situ magnetization is a magnetization method in which
a relatively small field of the order of millitesla repeatedly applied is used to
magnetize the superconductor. This paper describes a novel method for achieving this.