RAPID COMMUNICATION
L43
R Zeng, L Lu, J L Wang, J Horvat, W X Li, D Q Shi, S X Dou, M Tomsic and M Rindfleisch
We present a detailed analysis of the effects of excess Mg on the lattice parameters, the critical temperature
(Tc), the critical current
(Jc), the irreversibility
field (Hirr), and the
upper critical field (Hc2) of MgB2
bulks and wires produced by an in situ solid-state reaction method
and the powder-in-tube method, respectively. It was found that
Jc,
Hirr,
and Hc2
were significantly enhanced for Mg excess samples. All these properties were highly
sensitive to the processing temperature for Mg excess samples, while there was
only a weak dependence on processing temperature for normal ones. The
Tc variation
for the 10% Mg excess sample was 1.6 K (36.3–37.9 K) when the sintering temperature changed from 650
to 850 °C
while it only varied by 0.5 K (37.2–37.7 K) for the normal sample. The low-field
Jc for the 10% Mg excess
samples sintered at 750 °C
increased by a factor of 3, compared to that for the normal
MgB2 samples, while the
Hc2 for the 10% Mg excess
samples sintered at 650 °C
reached 8.7 T at 25 K, compared to 6.6 T for the normal sample. Rietveld refinement x-ray
diffraction (XRD) analysis showed that the MgO content was reduced in the 10% excess
Mg samples, leading to an increase in the effective cross section of the superconductor.
L48
F Colauto, E M Choi, J Y Lee, S I Lee, V V Yurchenko, T H Johansen and W A Ortiz
Vortex avalanches are known to occur in
MgB2
films within a certain range of temperatures and magnetic fields. These events, resulting
from a thermomagnetic instability, were first revealed by real-time magneto-optical
imaging, which exposed dendritic paths of abrupt flux propagation. This very powerful
technique has, however, a practical limitation, since sensors that are currently
available cannot be used at high magnetic fields. This letter shows that results
obtained using dc magnetometry are in good correspondence with those furnished by
magneto-optical imaging, demonstrating that the two techniques can be efficiently
used as complementary tools to map vortex avalanches in superconducting films.
L51
M S A Hossain, J H Kim, X Xu, X L Wang, M Rindfleisch, M Tomic, M D Sumption, E W Collings and S X Dou
We report the carbon (C) substitution effects of
MgB2+10 wt% C4H6O5
(malic acid) on the lattice parameters, critical temperature
(Tc), upper critical
field (Hc2), and
irreversibility field (Hirr) as a function of sintering temperature in the range from 600 to
900 °C. The
additive C4H6O5
as the C source resulted in a small depression in
Tc, but significantly increased the C substitution level, and hence improved the
Hc2
and Hirr
performance at a low sintering temperature of
600 °C
in conjunction with a short sintering period of 4 h. In addition, the low-temperature sintering
process resulted in small grain size and higher impurity scattering compared to a pure
MgB2
superconductor. These effects promote flux pinning.
PAPERS
721
L Palumbo, S Cagliero, A Agostino, M Truccato, M G Medici and P Volpe
In the present paper we report the results of photoconductivity
experiments carried out in nearly optimally doped, single-phase
Bi2Sr2CaCu2O8+x
(Bi-2212) whiskers. Samples with both straight and bent shapes have been investigated by
means of the four-probe and two-probe configurations in dark and in illuminated conditions.
Experimental data invariably show the absence of a persistent photoconductivity (PPC)
effect. Such observations, combined with the very high crystal quality of the whiskers,
which corresponds to the absence of defects acting as electron traps, can be explained in
the framework of the electron–hole pair excitation model (Kudinov et al 1990
Phys. Lett. A 151 358). In contrast, experimental data show a reversible increase of the
electrical resistance under illumination, which is fully consistent with a local heating
effect due to the thermal load induced by the light. Such resistance increase is
especially large for samples measured in the two-probe configuration, suggesting a
possible supplementary effect due to an interaction between the light and the
c-axis resistivity or the contact resistance.
728
B Andrzejewski, A Kowalczyk, A Jezierski and M R Lees
In this report we present experimental and theoretical investigations of the properties of the recently
discovered W7Re13B
superconductor. This compound is synthesized by means of inductive melting
and contains a pure phase with a sharp superconducting transition at
Tc = 7.22 K.
The superconductor exhibits type-II behaviour with reversible magnetic properties in a large part of
the H–T
diagram. The irreversibility line with the irreversibility field
µ0Hirr(0)
equal to 2 T is well separated from the upper critical field. The values of lower
µ0Hc1(0) and
upper µ0Hc2(0)
critical fields are equal to 8.8 mT and 11.8 T, respectively. These values correspond to penetration depth
λ, coherence length
ξ and Ginzburg–Landau
coefficient κ
equal to 2675 Å, 52 Å and 51, respectively. The critical current density
Jc is low and
equal to 4.9 kA cm−2
at zero magnetic field and at 2 K. The effect of pressure on superconducting properties is almost
negligible, probably due to the low compressibility of this compound. The pressure coefficient
dTc/dP is negative
and equal to −0.037 K GPa−1. The XPS spectrum and numerical calculations confirm that the main contributions to
the density of states at the Fermi level come from W(5d) and Re(5d) states.
736
Y Matsumoto, K Murakami, Y Kimoto, K Higuchi, A Nishida, T Akune and N Sakamoto
The magnetic field and temperature dependence of the magnetic hysteresis loop,
ΔM, for
grain-aligned HgRe0.18Ba2Ca2Cu3O8+y
specimens have been measured for two directions of field parallel (
-axis) and perpendicular (
-plane) to the c-axis of the crystal structure. The irreversibility field,
Birr = μoHirr, for each field direction is well fitted by a flux creep theory from Matsushita
et al (1990 Appl. Phys. Lett. 56 2039). The magnetic field dependence of the
ΔM
is fairly well described by using the resultant fitting parameters in the low-temperature
region, but coincidence between experimental results and the theoretical curve
is poor in the high-temperature region. The temperature dependence of
ΔM
in the low-temperature region is well described by the collective pinning theory of
Feigel’man et al (1989 Phys. Rev. Lett. 63 2303) or by the flux creep theory of Matsushita
et al. However, the dependence in the high-temperature region is far from the
predicted curves of these theories, so we tried to fit Burlachkov et al’ s theory
(1994 Phys. Rev. B 50 16770) to the experimental results, which means that two-dimensional
(2D) pancake vortices surmount the surface potential barrier. An exponential decay of the
ΔM
with increasing temperature in the high-temperature region has been successfully explained
by the theory.
742
A A Khurram, M Mumtaz, Nawazish A Khan, M M Ahadian and Azam Iraji-zad
The high temperature superconductor thin films
Cu1−xTlxBa2Ca3Cu4O12−δ
(Cu1−xTlx- 1234) are post-annealed in a nitrogen atmosphere. The zero-resistivity critical temperature
(Tc(R = 0)) of these thin films is increased from 92.3 to 104 K. The grain size is enhanced
and their morphology is improved with the post-annealing. The enlargement
of grain size is linked to fluctuation-induced conductivity (FIC) in the light of
Aslamazov–Larkin (AL) theory. The FIC measurements have shown that the cross-over of
three-dimensional (3D) to two-dimensional (2D) behaviour of fluctuations is shifted
to higher temperature values with an increase of post-annealing temperature.
These results have shown that the removal of oxygen and the increased grain
size are the most likely sources of the increase in the cross-over temperature,
T*
to higher values.
748
P J Masson, G V Brown, D S Soban and C A Luongo
Environmental protection has now become paramount as evidence mounts to support the
thesis of human activity-driven global warming. A global reduction of the emissions of
pollutants into the atmosphere is therefore needed and new technologies have to be
considered. A large part of the emissions come from transportation vehicles, including cars,
trucks and airplanes, due to the nature of their combustion-based propulsion systems. Our
team has been working for several years on the development of high power density
superconducting motors for aircraft propulsion and fuel cell based power systems for
aircraft. This paper investigates the feasibility of all-electric aircraft based on currently
available technology. Electric propulsion would require the development of high
power density electric propulsion motors, generators, power management and
distribution systems. The requirements in terms of weight and volume of these
components cannot be achieved with conventional technologies; however, the use of
superconductors associated with hydrogen-based power plants makes possible
the design of a reasonably light power system and would therefore enable the
development of all-electric aero-vehicles. A system sizing has been performed
both for actuators and for primary propulsion. Many advantages would come
from electrical propulsion such as better controllability of the propulsion, higher
efficiency, higher availability and less maintenance needs. Superconducting machines
may very well be the enabling technology for all-electric aircraft development.
757
George A Levin, Paul N Barnes and John S Bulmer
A two-dimensional model is introduced that describes DC current sharing between the
superconducting and normal metal layers in a configuration typical of YBCO-coated
conductors. The model is used to compare the effectiveness of a surround stabilizer and a
more conventional one-sided stabilizer. When the resistance of the interface between the
superconductor and the stabilizer is low enough, the surround stabilizer is less effective
than the one-sided stabilizer in stabilizing a hairline crack in the superconducting film.
765
D C van der Laan, J W Ekin, C C Clickner and T C Stauffer
We present a new experimental technique to measure the delamination strength under transverse tensile
stress of YBa2Cu3O7−δ
coated conductors for electric power applications. The delamination strength, defined as
the tensile stress at which the ceramic layers delaminate from one another, is measured at
76 K for different sample configurations. The delamination strength is reduced by as much
as 40% when the conductor is slit to smaller width, a standard fabrication process, and this
reduction is due to damage to the ceramic layers near the edges of the conductor. We found
that the delamination strength of slit coated conductors can be raised significantly by
reinforcing the conductor by laminating it with copper strips and adding solder fillets at
the edges. In relatively strong conductors, where the delamination strength is as
high as 15 MPa, the critical current does not degrade before actual delamination.
This fact greatly simplifies sample characterization of practical high-strength
conductors, since only mechanical measurements need to be made. The critical
current does, however, degrade significantly as a function of transverse stress before
delamination in weak conductors that have relatively low delamination strength below
15 MPa. We discuss how a soft metallic layer in YBCO coated conductors may limit
the transverse stress that the superconducting layer experiences in applications.
771
P Kováč, I Hušek, T Melišek and T Holúbek
Stabilized four-filament in situ MgB2/Ti/Cu/Monel
composite wire was produced by the rectangular wire-in-tube (RWIT) technique. 10 wt%
of nanosize SiC was added into the Mg–B powder mixture, which was packed
into the Ti/Cu and Monel tubes, respectively. The assembled composite was
two-axially rolled into wire and/or tape form and sintered at temperatures of
650–850 °C/0.5 h.
Stabilized MgB2
wire with Ti barrier is studied in terms of field-dependent transport critical current density,
effects of filament size reduction and thermal stability.
777
Hong-Chang Yang, Kuen-Lin Tsai, Ji-Cheng Chen, Chiu-Hsien Wu, Herng-Er Horng, Jyh-Horng Chen and Li-Wei Kuo
A surface coil composed of a miniature spiral
YBa2Cu3Oy (YBCO) thin film
resonator and a Bi2Sr2Ca2Cu2O3
(BSCCO) tape resonator were designed. The spiral YBCO resonator was fabricated onto one side of
a 2 × 2 cm2 LaAlO3
substrate, which was then coupled to the receiver via a tank circuit and a
fine-tuning copper coil to image small samples. Additionally, a BSCCO tape
resonator of 20 cm in diameter was coupled to a receiver coil and a fine-tuning
coil to image large samples. An improvement of the signal-to-noise ratio for
high-Tc
resonators over a conventional copper resonator is demonstrated.
781
A Biju, P M Sarun, S Vinu, P Guruswamy and U Syamaprasad
The critical current density of Bi2Sr2CaCu2O8+δ
(Bi-2212) superconductors can be enhanced either by changing the charge carrier
concentration (holes) to the optimum value, from the overdoped state, or by creating
flux pinning centres to inhibit the flux flow in magnetic fields. In this work we
substitute the rare earth La at the Sr site of Pb-doped Bi-2212 [(Bi, Pb)-2212].
La3+ ions
at the Sr2+
site decrease the hole concentration to the optimum value and enhance the superconducting
properties. Also La at the Sr site creates point defects which act as flux pinning
centres. These dual effects of La at the Sr site highly enhance the transport
JC
in self and applied magnetic fields.
785
D P Singh and Neeraj Khare
The temperature dependence of conduction noise and magnetic noise of a bulk sample of
La0.67Ba0.33MnO3
(LBMO) manganite was studied. It was observed that normalized
conduction noise decreases with a decrease of temperature down to
Tc
(paramagnetic to ferromagnetic transition temperature). For temperatures
T<Tc, the conduction noise showed an increase. The magnetic noise of the LBMO
sample was measured by employing a BSCCO rf-SQUID. An enhancement of
magnetic noise was observed at paramagnetic to ferromagnetic transition
temperature. The frequency spectrum of magnetic flux noise was found to exhibit
1/fα type behaviour,
where α = 0.82 ± 0.04. The analysis of the observed data revealed that enhancement of conduction noise below
Tc
was not due to the magnetic fluctuations. It could be due to the resistive disorders present
in the sample.
789
S H Wee, A Goyal, J Li, Y L Zuev, S Cook and L Heatherly
We report significant enhancement in the flux-pinning of epitaxial
NdBa2Cu3O7−δ
(NdBCO) films on rolling-assisted biaxially textured substrates (RABiTS) via the
incorporation of a two-dimensional array of columnar defects comprised of self-assembled
BaZrO3 (BZO)
nanodots. Pure NdBCO films and NdBCO films incorporating BZO nanodots, both with the same thickness
of 0.6 µm, were epitaxially grown on RABiTS by pulsed laser deposition. A very
dense and homogeneous distribution of BZO nanodot columns with
typical intercolumn spacing of around 15–20 nm oriented along the
c-axis of the film
was observed in the NdBCO+BZO
film. Compared to the pure NBCO film on RABiTS, the
NdBCO+BZO
film on RABiTS has an in-field critical current density
(Jc) of a factor of more than 2 in 0.1–1.5 T and a smaller power-law exponent
α∼0.21 in the field
regime where Jc∼H−α.
794
F Grilli and Stephen P Ashworth
Several AC power applications of YBCO-coated conductors (CCs) involve superconducting
tapes wound in coils. In such a configuration the superconducting tape is arranged as
closely packed turns, which strongly interact due to the generated magnetic field. This has
a strong influence on the AC losses, which are different from those of an isolated tape, and
need to be precisely quantified in order to predict and reduce the refrigeration requirements
of applications. In this paper we experimentally evaluate the transport AC losses in a
pancake coil composed of 25 turns of superconducting tape. We describe in detail the
measuring technique utilized, pointing out the issues in this kind of measurement.
We also present preliminary results of AC loss computation by finite-element
modelling.
800
S Ochiai, M Fujimoto, H Okuda, S S Oh and D W Ha
The local critical current along a sample length is different from position to position in a
long sample, especially when the sample is damaged by externally applied strain. In the
present work, we attempted to reveal the relation of the distribution of the local
critical current to overall critical current and the sample-length dependence of
critical current for slightly and significantly damaged Bi2223 composite tape
samples. In the experiment, 48 cm long Bi2223 composite tape samples, composed
of 48 local elements with a length of 1 cm and 8 parts with a length 6 cm, were
bent by 0.37 and 1.0% to cause slight and significant damage, respectively. The
V–I curve, critical
current (1 µV cm−1
criterion) and n
value were measured for the overall sample as well as for the local elements and parts. It
was found that the critical current distributions of the 1 cm elements at 0.37 and 1.0%
bending strains are described by the three-parameter- and bimodal Weibull distribution
functions, respectively. The critical current of a long sample at both bending
strains could be described well by substituting the distributed critical current and
n
value of the short elements into the series circuit model for voltage generation. Also the
measured relation of average critical current to sample length could be reproduced well in the
computer by a Monte Carlo simulation method. It was shown that the critical current and
n
value decrease with increasing sample length at both bending strains. The extent of
the decrease in critical current with sample length is dependent on the criterion
of the critical current; the critical current decreases only slightly under the
1 µV cm−1
criterion which is not damage-sensitive, while it decreases greatly with
increasing sample length under damage-sensitive criteria such as the
1 µV
one.
810
P Badica, H Oguro, S Awaji, G Nishijima and K Watanabe
Relaxation of the thermal residual strain in
Nb3Sn
wires is realized through cycles of multiple torsion loadings (‘pre-torsion’)
at room temperature. As a consequence, the critical current,
Ic, is enhanced. This effect is stronger than previously reported mechanical
treatments of multiple bending (‘pre-bending’). The maximum
Ic
is attained for complex mechanical treatments of pre-torsion and pre-bending.
Complex treatments allow efficient and relatively independent control of residual
strain relaxation over all three directions of the wire, resulting in enhancement of
Ic towards
the theoretical limit of the material. Our findings have an immediate positive impact on the performance
of Nb3Sn
wires and, hence, on their applications (e.g. react-and-wind coils).
814
T Lindström, C H Webster, J E Healey, M S Colclough, C M Muirhead and A Ya Tzalenchuk
We propose a scheme for circuit quantum electrodynamics with a superconducting flux–qubit coupled to
a high-Q
coplanar resonator. Assuming realistic circuit parameters, we predict that it is possible to
reach the strong coupling regime. Routes to metrological applications, such as
single-photon generation and quantum non-demolition measurements, are discussed.
822
K Suzuki, J Matsuda, M Yoshizumi, T Izumi, Y Shiohara, M Iwakuma, A Ibi, S Miyata and Y Yamada
Expectations are high for using coated conductors for electric power
applications not only because of better cost performance but also higher
Jc–B properties
compared with Bi2Sr2Ca2Cu3O10
(BSCCO) tapes. Furthermore, the coated conductors could also reduce AC losses by
the use of various methods in post-treatment. When a YAG laser was used for
scribing the superconductive layer, an AC loss reduction due to a decrease in
the width of the superconductivity layer could be confirmed in short samples.
In the case of AC applications using long tapes, high resistance between scribed filaments is
necessary. However, the resistance between the filaments scribed by a laser was as low as
10−3 Ω cm−1. The reason for the low resistance was the existence of dross in the filament spacings,
which was confirmed by a cross-sectional compositional mapping observation.
Although the superconductivity layer was divided by the laser, the dross of the metal
substrate made a bridge over the superconductivity filaments. Post-annealing in an
O2
atmosphere to oxidize the dross was carried out in order to increase the resistance.
Consequently, the resistance between the filaments was improved to be as high as
50 Ω cm−1. We succeeded in controlling the resistance value between filaments in a range five orders
of magnitude higher than that of the as-scribed YBCO film, through oxygen atmosphere
post-annealing.
827
Intikhab A Ansari, M Shahabuddin, Khalil A Ziq, A F Salem, V P S Awana, M Husain and H Kishan
Nano-Al2O3
doped Mg1−xAlxB2 with
0≤x≤6% were synthesized by
solid state reaction at 750 °C
in Fe tube encapsulation under a vacuum of
10−5 Torr. Resistance measurement
shows that the Tc
decreases with x and
zero resistivity for x = 0
and 6% are obtained at 38 and 35 K, respectively. XRD measurement shows that the
lattice parameter and cell volume also decrease monotonically with increasing
doping levels. From this we infer that the Al has been substituted in the lattice of
MgB2
at Mg sites. Resistivity measurement shows a systematic decrease in
Tc
with doping which also confirms the substitution of Al. Magnetization
studies in the temperature range from 4 to 35 K and in the magnetic
field up to 9 T shows a significant increase in the irreversibility field
(Hirr), critical current density
(Jc) and remanent magnetization
(MR) with increasing
concentration of the Al2O3
nanoparticle. At low fields we have observed large vortex instabilities (known as
a vortex avalanche) associated with all doped samples. The vortex-avalanche
effect is reduced with increasing temperature and vanishes near 20 K. The
results are discussed in terms of local-vortex instabilities caused by doping of
Al2O3
nanoparticles.
832
Motoharu Imai, Minoru Akaishi and Ichimin Shirotani
A magnetization study on the superconducting filled skutterudite
La0.8Rh4P12 has revealed the lower
critical field HC1(0) of 71(2) Oe
and the upper critical field HC2(0)
of 126(7) kOe. Using these values, the coherent length
ξ(0), penetration depth
λ(0) and Ginzburg–Landau
parameter κ(0) were
determined to be 5.1(1) nm, 3.1(2) × 102 nm and 60(3), respectively. The estimated critical current was
18.4 kA cm−2
at 4.2 K and 0 kOe using the Bean model.
836
V Sandu, G Aldica, P Badica, J R Groza and P Nita
High density (more than 90% of the theoretical density) bulk
samples with relatively large size (2.0 cm in diameter) of
MgB2, pristine and doped
with 5 mol% SiC and B4C
were obtained by the field-assisted sintering technique (FAST) from commercial
MgB2 powder.
The superconducting properties in the magnetic field of the doped samples show depressed upper critical field
Hc2 and irreversibility
field Hirr when compared
with pristine MgB2. The
reason for better Hc2
and Hirr
in the undoped sample is not clear. Most probable is that this is due to the limited
diffusion time which restricts the substitution of carbon for boron in this
short-time processing method as well as due to the way grain boundaries are
formed in the FAST process. However, all our samples have shown higher values of
Hc2 and
Hirr than the values reported
previously for FAST-MgB2
samples. The data were further investigated through scaling analysis. Data suggest that both additions of
SiC and B4C
stabilize two well defined pinning regimes in FAST-processed
MgB2. At low temperatures, the pinning occurs at the grain border whereas at high temperatures,
T≥24 K, there is
mixed pinning (H≤5 T).
843
M Y Li and Z Han
The effect of lead-rich phases on the microstructure and properties of (Bi, Pb)-2223/Ag
tapes has been studied. Powders containing different types of lead-rich phases were
prepared by controlling the processing parameters, including temperature, time and oxygen
partial pressure. Then, monofilament (Bi, Pb)-2223/Ag tapes were fabricated using these
powders. The phase compositions of the powders and tapes were analysed by x-ray
diffraction and the microstructure of these tapes was observed using scanning electron
microscopy. Experimental results show that the lead-rich phases in powders played an
important role in the formation of the (Bi, Pb)-2223 phase, and the microstructure and the
superconducting properties of (Bi, Pb)-2223/Ag tapes. The formation process of
(Bi,Pb)2Sr2CaCu2Ox
in tape fabricated using the powder containing
Ca2PbO4
is different from a tape fabricated using the powder containing
Pb3Sr2.5Bi0.5Ca2CuOy, which differs in the formation process and grain sizes of the (Bi, Pb)-2223 phase. Therefore,
the critical currents of (Bi, Pb)-2223/Ag tapes containing various lead-rich phases are different.
The highest critical current is obtained for tape fabricated using powder containing both
Ca2PbO4
and 3321 phases.
851
Sangjun Oh, Chulhee Lee, K W Cho, Keeman Kim, D Uglietti and R Flükiger
We find a simple expression for the field dependences of the
n-value
for Nb3Sn
strands which gives reasonable fits to empirical data. It is also found that a relationship between the
n-value and the critical current, which is obtained from an assumed reduction of the
flux line lattice shearing pinning force due to thermal activation, can describe
the field dependence of the critical current. Using the relation between the
n-value and the critical current, we propose a scaling law which we have called the Kramer
model including thermal activation. It is shown that the proposed scaling law can explain
the critical current data at 4.2 K, even at high field near the upper critical field. It is also
compared with Ekin’s strain scaling law.
859
A Stenvall, A Korpela, J Lehtonen and R Mikkonen
Usually overheating of the sample destroys attempts to measure
voltage–current curves of conduction cooled high critical current
MgB2
wires at low temperatures. Typically, when a quench occurs a wire burns out due to
massive heat generation and negligible cooling. It has also been suggested that high
n values
measured with MgB2
wires and coils are not an intrinsic property of the material but arise due to
heating during the voltage–current measurement. In addition, quite recently low
n values
for MgB2
wires have been reported. In order to find out the real properties of
MgB2
an efficient computational model is required to simulate the voltage–current measurement.
In this paper we go back to basics and consider two models to couple electromagnetic and
thermal phenomena. In the first model the magnetization losses are computed
according to the critical state model and the flux creep losses are considered
separately. In the second model the superconductor resistivity is described by the
widely used power law. Then the coupled current diffusion and heat conduction
equations are solved with the finite element method. In order to compare the models,
example runs are carried out with an adiabatic slab. Both models produce a similar
significant temperature rise near the critical current which leads to fictitiously high
n
values.
865
Ernst Otto, Mikhail Tarasov and Leonid Kuzmin
We present a novel Ti-based direct-write technology for fabricating
Ti–TiO2–Al tunnel junctions for bolometer and thermometry applications. The goal of our research is to
develop simple and efficient technology for fabricating SIS tunnel junctions between Ti and Al with
TiO2
as an insulating barrier. The key point of this technology is the deposition of a Ti film
as a base electrode and deposition of an Al electrode after oxidation of the Ti.
This approach allows one to realize any geometry of the tunnel junctions and of the
absorber with no limitation related to the area of the junctions or the thickness of the
absorber. In particular, a very thin and completely flat absorber can be created with no
bending parts, which is not possible using the shadow evaporation technique or standard
trilayer technology. Besides, the proposed new approach does not require one-cycle
evaporation for deposition of tunnel junctions which gives us more freedom in the geometry
of the counter-electrodes.
The junctions are to be used for bolometer applications, such as the fabrication of
microwave receivers for sensitive measurements in new generation telescopes,
e.g. CLOVER and BOOMERANG projects including polarization cosmic microwave
background radiation measurements, and the OLIMPO balloon telescope project which
is dedicated to measuring the Sunyaev–Zeldovich effect in clusters of galaxies.
As the first step, SIN tunnel junctions have been fabricated and characterized.
870
Y Liu, S L Wan and X G Li
High-quality c-axis oriented La2CuO4
films were prepared by an off-axis magnetron sputtering method on a
LaSrAlO4(001)
substrate. After a chemical oxidation treatment at room temperature using NaClO as the oxidizing
agent, La2CuO4+δ
films show a superconducting transition around 28 K. The elongation of the
c-axis
of La2CuO4+δ
films follows the square-root law
with increasing oxidation time, while the full-width at half-maximum (FWHM) for
the rocking curve measured on the (006) reflection shows a linear increase. A
strong delocalization behavior of charge carriers is observed in superconducting
La2CuO4+δ
films. The two-phonon Raman bands between
750<ν<1500 cm−1 together
with the 692 cm−1
vibration mode observed in as-grown films disappear with
doping with excess oxygen. After removing the excess oxygen in
La2CuO4+δ
films these bands become visible again.
875
V Sokolovsky and V Meerovich
AC losses in the superconducting parts of tapes and multifilamentary coated conductors
that are subjected to AC magnetic fields are an important component of the
total losses in such composites. The analytical expression for AC losses in a thin
superconducting strip with a power-law voltage–current characteristic and critical current
depending on a magnetic field is obtained for the case of asymptotically high
perpendicular magnetic fields. The losses caused by closure currents are estimated.
The results show that the Bean model gives significantly understated values for
coated conductors. The applicability of the obtained expressions is analyzed.
880
J A Xia, N J Long, N M Strickland, P Hoefakker, E F Talantsev, X Li, W Zhang, T Kodenkandath, Y Huang and M W Rupich
The microstructure of metal-organic deposited
YBa2Cu3O7−δ
with dysprosium (Dy) additions has been investigated by transmission electron microscopy
(TEM). Dy additions which increase the density of normal-state nanoparticles in the
YBCO have been demonstrated to enhance the critical current densities in moderate
magnetic fields. The influence of nanoparticles, stacking faults and other planar defects on
flux pinning is discussed. We observed a high density of nanoparticles in the size range of
10–50 nm, which may act as flux pinning centres to enhance the critical current density of
the material. Stacking faults and planar defects are observed which may also be
effective flux pinning centres in YBCO samples with and without Dy addition.
886
M H Hancock and N Bay
Applying the powder in tube (PIT) method, single-filament
MgB2/Fe
wire and tape has been manufactured applying both the ex situ and the in situ
approach. The influence of the roll diameter in three-step flat rolling on the
powder density and critical temperature has been examined using rolls of
∅70,
∅150
and ∅210 mm in each step. The investigation has shown that the in situ powder is more readily
compacted than the ex situ powder, with an average increase of relative density after
mechanical processing of 37% for in situ powder and 19% for ex situ powder. Statistical
analysis showed that the choice of roll diameter had the largest influence in the first of the
three reductions used in the flat rolling. In this first reduction, for ex situ tapes, rolls of
∅70 or
∅150 mm proved best,
whereas the ∅70 mm roll appeared best for in situ tapes. Overall, the evidence suggested that the combination of the
∅70 mm roll in the first and second reductions followed by the
∅150 mm
or ∅210 mm roll in the last reduction was the optimum strategy for both powder types. AC
susceptibility testing showed that for the in situ tapes there was no correlation
between the powder density and the critical temperature. For ex situ tapes the
critical temperature correlated to some degree with the powder density; the critical
temperature also proved to be more sensitive to the powder density for ex situ samples.
891
V M Dmitriev, I V Zolochevskii, E V Bezuglyi and D S Kondrashev
Current steps in the current–voltage characteristics of wide superconducting Sn
films exposed to microwave irradiation were observed in the resistive state with
phase slip lines. The behavior of the magnitude of the steps with the applied
irradiation power was found to be similar to that for the current steps in narrow
superconducting channels with phase slip centers and, to some extent, for the
Shapiro steps in Josephson junctions. This provides evidence for the Josephson
properties of the phase slip lines in wide superconducting films and supports the
assumption about the similarity between the processes of phase slip in wide and narrow
films.