TOPICAL REVIEW
R47
M Eisterer
This review focuses on the superconducting properties of
MgB2
that are relevant for power applications. The reversible mixed state parameters are the most
important, since they define the limiting conditions for loss-free currents: the transition
temperature, the upper critical field and the depairing current. They also determine the
flux pinning energy, the pinning force and the elastic properties of the flux line lattice and,
therefore, strongly influence the critical current densities. The magnetic properties of
magnesium diboride are anisotropic and influenced by the two different energy gaps of the
σ- and
π-bands. Whereas the transition temperature could not be enhanced
significantly during the past five years, the upper critical field was considerably
increased by impurity scattering or doping. Flux pinning is very weak in
MgB2
single crystals and was only improved by irradiation techniques so far. In
polycrystalline samples, grain boundary pinning seems to play the dominant
role. High critical currents close to the theoretical limit were found in
c-axis
oriented thin films. The anisotropy of the upper critical field strongly reduces the critical currents in
untextured MgB2
at high magnetic fields, where the supercurrents become highly percolative, since not all
grains are superconducting anymore. The performance of polycrystalline wires and tapes
was significantly improved during the past few years by increasing the upper critical field
and by reducing its anisotropy. Pinning seems to be nearly optimized in many forms of this
material, but the connectivity between the grains might be further improved.
PAPERS
1093
S Takács
We calculate the hysteresis losses in the slab geometry configuration for an applied
magnetic field and current with a phase shift between them. The result leads to maximum
losses with the field and current in phase and minimum losses at a phase shift of
π/2. Although until now we have had no explanation of some experimental results suggesting a
shift for both these extreme values, the dependence on the phase shift of the calculated
ratio between the minimum and maximum losses is in good agreement with these results.
Therefore, they can be used in a first approximation for designing magnetic systems with
high-Tc
superconductors for those AC applications in which phase shift can occur. In addition, it is
emphasized that the results can be very different, depending on the form of the temporary
change of the applied field and current, in contradistinction to the case of applying only the
field or current. A linear temporary change is given as an example, which demonstrates
that the loss decrease at non-zero phase shift can be considerably higher than for the
sinusoidal field and current change.
1097
L Rostila, J Lehtonen, R Mikkonen, J Šouc, E Seiler, T Melíšek and M Vojenčiak
In this paper, an optimization method to determine the
magnetic field dependence of the intrinsic critical current density,
Jc(B),
is introduced. First of all the critical current is measured in various external magnetic fields. Then
the Jc(B)-dependence that fits optimally to the measurements is searched for. In these
computations the self-field of the sample is taken into account and thereby measurements
performed in low external magnetic fields, below 0.1 T, can be exploited. Here the
Jc(B)-dependence of YBCO material is described by the Kim model, which is modified to include the
anisotropy also. Thus, there are four parameters to search for: zero field critical current density
Jc0, reference field
B0, Kim model exponent
α and anisotropy
scaling factor γ. The search for these parameters was computationally challenging
but computation times were still satisfactory. As examples, the
Jc(B)-dependences
of two YBCO samples from different manufacturers were found. For both samples, all parameters except
B0 were near each other.
For example, Jc0 values for
both samples were about 0.9 × 1010 A m−2.
1101
George A Levin and Paul N Barnes
We consider the distribution of an electric field in
YBa2Cu3O7−x
(YBCO)-coated conductors for a situation in which the DC transport current is forced into
the copper stabilizer due to a weak link—a section of the superconducting film with a
critical current less than the transport current. The electric field in the metal substrate is
also discussed. The results are compared with recent experiments on normal zone
propagation in coated conductors in which the substrate and stabilizer are insulated from
each other. The potential difference between the substrate and stabilizer, and the electric
field in the substrate outside the normal zone, can be accounted for by a large
screening length in the substrate, comparable to the length of the sample. During a
quench, the electric field inside the interface between YBCO and the stabilizer,
as well as in the buffer layer, can be several orders of magnitude greater than
the longitudinal macroscopic electric field inside the normal zone. We speculate
on the possibility of using microscopic electric discharges caused by this large
(∼kV cm−1) electric field as a means to detect a quench.
1108
M Herrmann, W Häßler, C Mickel, W Gruner, B Holzapfel and L Schultz
Polycrystalline samples of MgB2
doped with reactive nanostructured carbon were synthesized by pressure assisted sintering
of mechanically alloyed precursors. Varying the nominal carbon concentration from
x = 0 to 0.316,
the effects of carbon doping on the lattice parameter, lattice strain, actual amount of incorporated carbon
(xactual), grain size, normal
state resistivity (ρ), connectivity, superconducting transition
(Tc), critical
fields (Birr and
Bc2) and critical current
density (Jc) as well as
the pinning force (Fp) were evaluated. An evident solubility limit of carbon within the
MgB2 matrix,
forming MgB2−xCx
with an xactual≈0.125, was observed. In addition to the carbon saturation the superconducting properties,
e.g. Tc, Bc2 and
Jc, also
reflect saturation effects with respect to the actual carbon concentration. Improved electron scattering
in MgB2−xCx
seems responsible for the observed enhancement of
Bc2 to
11.4 T at 20 K. On the other hand, calculations of the flux-pinning forces show a dramatic decrease
of Fp,max
with increasing carbon concentration. Therefore we conclude the
observed improvement in critical current density at applied fields
>6 T to result mainly from the raised upper critical field.
1115
S Horii, K Yamada, H Kai, A Ichinose, M Mukaida, R Teranishi, R Kita, K Matsumoto, Y Yoshida, J Shimoyama et al
We report the effectiveness of barium niobate as a needle-type vortex pinning
center, as well as a change in the vortex state in Ba–Nb–O (BNO)-doped
ErBa2Cu3Oy thin films.
BNO doping was effective for improving critical current properties for a magnetic field direction parallel
to the c
axis of a matrix film and induced the generation of columnar defects
with diameters of 5–25 nm. The irreversibility lines were also changed
by the BNO doping and were similar to those of heavy-ion-irradiated
YBa2Cu3Oy
crystals in which the vortex Bose glass state was induced. It is suggested that the
characteristic field relevant to crossover from the Bose glass to collective pinned glass depends
on the BNO doping level. There is a possibility that Ba-based perovskite-type oxides promote
the formation of nanorods universally and these nanorods play the role of one-dimensional
c-axis-correlated pinning centers.
1120
G L Bhalla and Pratima
The temperature-dependent resistivity of a polycrystalline
YBa2Cu3O7−δ
superconductor under magnetic fields up to 5 kG has been investigated by
employing two models invoking different mechanisms of dissipation, namely
the Kosterlitz–Thouless (KT) model of vortex–antivortex unbinding for
two-dimensional systems (2D) and the Ambegaokar–Halperin (AH) model of thermally
activated phase slip (TAPS) for granular superconductors. The experimental
R–T
data shows a partial agreement with the KT model in the intermediate
temperature range, justifying the picture of a quasi-two-dimensional polycrystalline
YBa2Cu3O7−δ
superconductor. Deviations from the KT model are apparent in the region near the onset transition temperature
(TC) and the offset
transition temperature (TCO). On the other hand, excellent agreement is obtained with the AH model over the entire transition
range. The resistivity curves under different magnetic fields show a scaling with the barrier parameter
‘γ’ in the AH model. The resistivity curves can be made to merge with each other by plotting
the inverse square root of normalized resistance, i.e.
versus γ∼A(H)(1−T/TC)m, where A(H)
is an adjustable field-dependent parameter and
‘m’ is a fixed parameter.
1125
Chenggang Zhuang, Xiaoxian Liu, Tao Guo, Bo Wang, Xingguo Li, Chinping Chen and Qingrong Feng
The effect of the size of the B powder and the Mg powder on
MgB2
phase formation has been studied by the technique of in situ high-temperature resistivity
(HT-ρ(T)) measurement. Two characteristic temperatures indicating the phase formation, the onset point,
Tonset, and the
completion point, TPF, were directly determined during the continuous heating process. These two temperatures
of the samples synthesized using nanometer-size B powder (Nano-B) and micrometer-size
B powder (Micro-B) with nanometer-size Mg (Nano-Mg) are almost the same,
i.e. Tonset = 713 K
and TPF∼763 K, respectively, indicating that the phase formation temperature of
MgB2
does not primarily depend on the particle size of the B powder. A similar process was then
carried out on Mg powders with the same B powder. An exponential relationship
between the onset phase formation temperature and the Mg powder size is clearly
shown, which can be fully fitted by a modulated diffusion equation and which gives
Q = 421 kJ mol−1
describing the grain boundary activation energy of Mg diffusing into B. We also find that the
MgB2
crystallites along the [101] direction have the lowest formation energy, revealed by
x-ray diffraction (XRD) analysis on raw Mg powders, and the corresponding
MgB2
crystallites aligned along [101] will be formed preferentially in the
sintering process. This result is useful for the understanding of
MgB2
phase formation in the solid reaction process.
1130
John R Clem, J H Claassen and Yasunori Mawatari
A finite stack of thin superconducting tapes, all carrying a fixed current
I, can be approximated by an anisotropic superconducting bar with critical current density
Jc = Ic/2aD, where
Ic is the critical current
of each tape, 2a is the
tape width, and D
is the tape-to-tape periodicity. The current density
J
must obey the constraint
, where the tapes lie parallel to the
x axis and are stacked
along the z axis.
We suppose that Jc
is independent of field (Bean approximation) and look for a solution to the critical state for arbitrary height
2b of the stack.
For c<|x|<a we have
J = Jc, and for
|x|<c the critical state
requires that Bz = 0. We show that this implies
in the central region. Setting c
as a constant (independent of z) results in field profiles remarkably close to the desired one
(Bz = 0 for
|x|<c) as long as the
aspect ratio b/a
is not too small. We evaluate various criteria for choosing
c, and we show that the calculated hysteretic losses depend only weakly on how
c is chosen. We
argue that for small D/a
the anisotropic homogeneous-medium approximation gives
a reasonably accurate estimate of the ac losses in a finite
Z stack. The
results for a Z
stack can be used to calculate the transport losses in a pancake coil wound with
superconducting tape.
1140
X Y Kong, K Sakuta and H Itozaki
In a superconducting quantum interference device (SQUID) probe microscope, the
existence of a needle with high permeability as a flux guide can increase the spatial
resolution. Also, the flux guide makes it possible to measure the samples in air at room
temperature. Using a finite element method (FEM), we analyzed the property
of a magnetic shielding cylinder with high permeability Permalloy around the
needle. Simulation results show that a cylindrical shield around the flux guide can
increase the spatial resolution of the SQUID probe microscope. Also, a model of a
small SQUID has been designed and the calculated result shows that the spatial
resolution is higher than a SQUID with the flux guide and the shield around it.
1144
Ataru Ichinose, Kazuaki Naoe, Tomoya Horide, Kaname Matsumoto, Ryusuke Kita, Masashi Mukaida, Yutaka Yoshida and Shigeru Horii
BaZrO3
nanorods are known to be effective pinning centers as
c-axis-correlated pinning centers. Furthermore,
BaZrO3 nanorods
in REBa2Cu3Oy
(RE: rare-earth element) films are formed by self-assembled stacking of
BaZrO3
using a target mixture of a superconductor and
BaZrO3
for pulsed-laser deposition, which is a very easy fabrication technique. The density of
BaZrO3 nanorods
in YBa2Cu3Oy
(YBCO) films can be controlled by varying the
BaZrO3 content in a
target. The BaZrO3
addition has two functions for superconductivity; one is the improvement
of pinning forces due to the addition of pinning centers and the other is
Tc degradation.
The optimum BaZrO3
addition for Jc
improvement in magnetic fields is found to be around 3 wt% because of a
trade-off between the two functions described above. Furthermore, the length of
BaZrO3
nanorods is found to be controlled using two types of target: pure YBCO and a mixture of YBCO and
BaZrO3. Varying
the BaZrO3
nanorod length has an effect on the pinning mechanism. In particular, magnetic field angle dependences of
Jc are varied
from c-axis-correlated pinning to nearly random pinning by changing the nanorod length. The
magnetic field at the crossover of the pinning mechanism seems to be adjusted by the
BaZrO3
nanorod length.
1151
J H Lee and Y C Kim
Although an intergranular superconducting system is definitely different from a conventional
type-II superconductor in several aspects such as flux shape, flux size, and flux behaviors,
its magnetic properties have been described by the critical state model in an equivalent
manner to those of a type-II superconductor’s. Instead of the critical state model, we
suggest another primitive model which is able to describe the magnetic properties of an
intergranular system. We have made a model calculating the magnetic susceptibility of a
superconducting coaxial cylindrical multi-shell structure zero-field-cooled under an external
field and have applied the model to susceptibility versus temperature data of a
YBa2Cu3Ox
polycrystal. Calculation results by this model concurred well with the experimental data. A
physical view point of this model is that an intergranular superconducting system
zero-field-cooled under an external field can be treated to be a hypothetical coaxial
multi-shell structure.
1155
Ernst Otto, Mikhail Tarasov, Gustav Pettersson, David Gustavsson and Leonid Kuzmin
We present superconductor–insulator–normal metal (SIN) tunnel junction thermometers made of arrays of
4–100 Al–Al2O3–Cu SIN tunnel junctions fabricated in direct-write technology. The technology is based on
in situ evaporation of the superconductive electrode followed by the oxidation and the
normal counter-electrode as a first step and deposition of normal metal absorber as a
second one.
This approach allows one to realize any geometry of the tunnel junctions and of the
absorber with no limitation related to the size of the junctions or the absorber, which is not
possible using the shadow evaporation technique.
Measurements performed at 300 mK showed the high quality of
the fabricated tunnel junctions, low leakage currents, and that an
Rd/Rn
ratio of 500 has been achieved at that temperature.
The junctions were characterized as temperature sensors, and
voltage versus temperature dependence measurements showed a
dV/dT of
0.5 mV K−1
for each single junction, which is typical for this kind of tunnel junction. A temperature resolution
of ± 5 µK
has been achieved which is much better than the previously reported value of
± 30 µK
for this type of thermometer.
1159
Yu V Cherpak, V O Moskaliuk, A V Semenov, V L Svetchnikov, C G Tretiatchenko and V M Pan
The obtained electron backscattering diffraction data and high-resolution transmission
electron microscopy have shown that the nanostructure of epitaxial HTS YBCO films
evolves essentially with the film thickness. This happens due to a high deposition
temperature and a high dislocation mobility that induce polygonization, dislocation
rearrangement and a remarkable reduction of the out-of-plane dislocation density.
The analysis of experimental thickness dependences of the critical current in
the framework of existing pinning models leads to the conclusion that the
c-axis-correlated pinning by out-of-plane edge dislocations plays a dominant role. Thus, the
evolution of the dislocation nanostructure is responsible for the critical current density
reduction. Embedding of nanoparticles into HTS films should be useful only if they are
coherently coupled with the matrix and extra dislocations are being formed during
the film growth. The nanoparticles just preserve a high density of dislocations.
Another effect is self-assembling of nanoparticles within dislocation cores forming
a ‘bamboo structure’. This phenomenon may result in an enlargement of the
dislocation normal core and an essential increase of the elementary pinning force.
1165
M R Osorio, J A Lorenzo, J A Veira and F Vidal
Here, we study the behaviour of an inductive superconducting fault current limiter (SFCL)
whose secondary is a bulk cylinder with an array of appropriately distributed weak zones.
This design allows heat to be removed by conduction from the hot weak zones, which
absorb the power dissipation, to the remaining colder parts of the cylinder. Our work
highlights the possibility of overcoming the limitations of high power SFCLs based on bulk
cylinders, which present recovery time values well beyond the maximum value tolerated in
a distribution line.
1169
Ji Young Huh, Won Kyung Seong, Soon-Gil Jung and W N Kang
The effects of Mg deficiency in MgB2
films grown by hybrid physical–chemical vapor deposition were
investigated after vacuum annealing at various temperatures. High-quality
MgB2 films
grown on c-cut Al2O3
substrates with different superconducting transition temperatures
(Tcs)
of 40.2 and 41 K were used in this study. As the annealing temperature was increased from 200 to
800 °C, the Mg content in
the MgB2 films systemically
decreased, but the Tcs
did not change, within ± 0.12 K, until the annealing temperature reached
700 °C. For
MgB2 films
annealed at 800 °C
for 30 min, however, no superconductivity was observed, and the temperature
dependence of the resistivity showed a semiconducting behavior. We also found that
the residual resistivity ratio decreased with increasing annealing temperature.
1173
L Ji, S L Yan, Q L Xie, S T You, T G Zhou, M He, T Zuo, X Zhang, J L Li, X J Zhao et al
We fabricated (Tl0.95Bi0.2)(Sr0.8Ba0.2)2Ca2Cu3Ox
(Tl, Bi-1223) superconducting thin films on a
LaAlO3(001)
substrate by a three-step process including magnetron sputtering and two
post-annealing processes. In the post-annealing process we found that the
(Tl0.95Bi0.2)(Sr0.8Ba0.2)2Ca1Cu2Ox
(Tl, Bi-1212) phase formation played a very important role in obtaining the Tl,
Bi-1223 superconducting phase. So, the precursors were annealed at lower
temperature to form the Tl, Bi-1212 phase entirely, and then almost pure Tl,
Bi-1223 phase superconducting thin films could be obtained by annealing the Tl,
Bi-1212 film at higher temperature. The superconducting critical temperature
Tc of the
Tl, Bi-1223 film annealed in oxygen and in argon was 111 K and 107 K, respectively. The critical current
density Jc
(77 K, 0 T) of the Tl, Bi-1223 film annealed in oxygen was as high as
3.7 MA cm−2.
1178
Yoshimitsu Hishinuma, Akihiro Kikuchi and Takao Takeuchi
The compound MgB2
has a higher Tc
value (39 K) and shorter decay time for induced radioactivity than Nb-based superconducting materials such
as Nb–Ti, Nb3Sn
and Nb3Al.
However, the Jc
value of MgB2
wire is lower than Nb–Ti alloy superconducting wire, and further
Jc
improvement is required for use in an advanced fusion reactor application. In order to improve
Jc
properties, we tried to investigate a reconsideration of the heat treatment condition
through comparisons with low-temperature and long-time treatment, so-called
‘low-temperature diffusion’. We confirmed that there was no reduction in
Tc values
compared with conventional processes when heat treated at low temperatures and for longer times
(450 °C for 200 h). Furthermore,
core Jc values when
heat treated at 450 °C
increased with extended heat treatment time, and then the maximum core
Jc value was
found to be over 1000 A mm−2
at 4.2 K under 5 T for the 200 h treatment sample and its value was higher than for conventional
samples with SIC addition. From the results of SEM observation, 100 nm grain-sized
MgB2
microcrystals were densely formed in the wire core and these nanograin sizes of the
MgB2 phase might
affect the Jc
improvement in the low and middle magnetic field regions. On the other hand, we tried to
fabricate 100 m classed mono-cored Ta sheathed wire samples having stabilized Cu in order
to investigate the workability of the Ta-sheathed sample for possible use in an advanced
fusion reactor application. We found that the wire deformation of 100 m classed
wire without breaking was successful for this sample, and this result proved the
good workability and possibility of fusion application of metal Ta sheathed wire.
1184
Tao Zuo, Lan Fang, Shaolin Yan, Xinjie Zhao, Tiege Zhou, Shitou You, Weigang Ma, Hongwei Yue and Qinglian Xie
The empirical tuning of high temperature superconducting (HTS) filters is usually
time-consuming and expensive. A computer-aided tuning method is presented in this
paper. By means of optimization, the method diagnoses detuning of individual resonators
quantitatively in the tuning process, and then by using neural network models the method
is able to give the operator a decision on how much the corresponding tuning
screws should be tuned. So, compared with the empirical tuning method, this
method can be used to tune the HTS filters accurately with less time and cost.
1189
H Y Wu, K Q Ruan, J Yin, S L Huang, Z M Lv, M Li and L Z Cao
Samples of stoichiometric composition
Bi1.8Pb0.4Sr2−xKxCa2−yNdyCu3Oz with
x = 0, 0.01,
0.02, and y = 0, 0.01, 0.02 were prepared by the solid state reaction method. Post-annealing experiments were carried
out at 500 °C
for 30 h in order to improve the oxygen homogeneity. They were characterized by the x-ray
diffraction (XRD) technique, field emission scanning electronic microscopy (FE-SEM), resistivity,
magnetization and Raman measurements. The superconducting transition temperature
Tczero of the
samples varies from 99 to 110 K for different doping. The superconductivity and the critical current density
(Jc) of
the sample single doped with K are improved compared with the undoped one. We attribute the change
of Tc
to the variation of carrier concentration. Additionally, the observed change of the normal
state resistivity is related not only to carrier concentration but also to the nature of grain
boundary links. These analyses are confirmed by Raman and SEM measurements.
1193
A Talapatra, S K Bandyopadhyay, Pintu Sen, A Banerjee and R Rawat
We report isothermal magnetization and magnetoresistance measurements performed on 160 MeV
Ne+6 ion irradiated
polycrystalline MgB2. After irradiation, the critical current density is observed to increase at high
magnetic fields. The irreversibility line and upper critical field show an
increase with introduction of damage due to irradiation. The scaling of
Hirr
with temperature shows weak pinning behaviour. The maximum
pinning force density has a temperature dependence similar to that of
Hirr(T). Reduced pinning
force density fp(H)
curves show a predominant grain boundary pinning.
1198
Xianping Zhang, Yanwei Ma, Zhaoshun Gao, Dongliang Wang, Zhengguang Yu and Lei Wang
A series of C doped and undoped
MgB2 tapes
sintered at 600–950 °C
was fabricated. The relationships between the critical current properties,
crystallinity and microstructures were systematically studied as functions
of the C doping level and heating conditions. A decrease in the
a-axis length due to carbon substitution was observed in the C
doped samples. The full width at half maximum (FWHM) of the
MgB2
(101) peak increased with increasing C doping level, suggesting that the
introduction of lattice defects and/or the decrease of the grain size of
MgB2
occurred on C doping. Due to the substitution of C for B, the upper critical field was improved in C
doped MgB2
samples. Substantially improved critical current density,
Jc, was found in all of the C doped samples. At 4.2 K, 10 T,
Jc
reached 2.2 × 104 A cm−2
in the 8% C doped samples.
1205
D Stamopoulos, E Manios and M Pissas
It is generally believed that superconductivity and magnetism are two antagonistic
long-range phenomena. However, as was preliminarily highlighted in Stamopoulos et al (2007 Phys. Rev. B 75 014501), and extensively studied in this work, under specific
circumstances these phenomena instead of being detrimental to each other may even
become cooperative so that their synergy may promote the superconducting properties of a
hybrid structure.
Here, we have studied systematically the magnetic and transport behavior
of such exchange biased hybrids that are comprised of ferromagnetic (FM)
Ni80Fe20 and
low-Tc
superconducting (SC) Nb for the case where the magnetic field is applied parallel to the
specimens. Two structures have been studied: FM–SC–FM trilayers (TLs) and FM–SC
bilayers (BLs). Detailed magnetization data on the longitudinal and transverse
magnetic components are presented for both the normal and superconducting
states. These data are compared to systematic transport measurements including
I–V
characteristics. The comparison of the exchange biased BLs and TLs that are studied here
with the plain ones studied in Stamopoulos et al (2007 Phys. Rev. B 75 184504) enable us
to reveal an underlying parameter that may falsify the interpretation of the transport
properties of relevant FM–SC–FM TLs and FM–SC BLs investigated in the recent
literature: the underlying mechanism motivating the extreme magnetoresistance
peaks in the TLs relates to the suppression of superconductivity mainly due to
the magnetic coupling of the two FM layers as the out-of-plane rotation of their
magnetizations takes place across the coercive field where stray fields emerge in their
whole surface owing to the multidomain magnetic state that they acquire. The
relative in-plane magnetization configuration of the outer FM layers exerts a
secondary contribution on the SC interlayer. Since the exchange bias directly
controls the in-plane magnetic order it also controls the out-of-plane rotation of the
ferromagnets’ magnetizations so that the magnetoresistance peaks may be tuned at will.
All the contradictory experimental data reported in the recent literature are discussed
fairly in the light of our results; based on a specific prerequisite we propose a
phenomenological stray-field mechanism that efficiently explains the evolution of the
magnetoresistance effect in TLs. Our experiments not only point out the need for a new
theoretical treatment of FM–SC hybrids but also direct us toward the design of efficient
supercurrent-switch elemental devices.
1223
T Doi, H Kitaguchi, S Hata, K Fukuyama, K Masuda, K Takahashi, T Yoshidome, Y Hakuraku and N Kuwano
We prepared MgB2/Ni
and MgB2/B
alternately-layered films using electron beam evaporation and coaxial vacuum
arc evaporation techniques without any post-annealing. The thickness of each
MgB2
layer was designed to be 42, 24 or 15 nm for both
MgB2/Ni
and MgB2/B
alternately-layered films. We confirmed that the layered structure was successfully obtained
from the scanning transmission electron microscopic cross-sectional image of the
MgB2/Ni
alternately-layered film. The critical temperature,
Tc, of the alternately-layered film decreased as the
MgB2 layer became
thinner, for both MgB2/Ni
and MgB2/B films.
Moreover, the Tc was
affected by only the MgB2
layer thickness, and was independent of the inserted layer materials.
1228
M Mumtaz and Nawazish A Khan
The intergranular coupling of the
Cu0.5Tl0.5Ba2Ca2Cu0.5Zn2.5O10−δ
superconductor has been studied by resistivity and AC magnetic susceptibility
measurements. The main objective of the present study is to enhance the intergranular
coupling of this compound by post-annealing the samples in nitrogen, oxygen and air
atmospheres. Any improvement to the intergrain coupling may be promoted by a change of
oxygen content in the final compound. The AC susceptibility measurements have shown
that the intergranular coupling peak observed in the out-of-phase component
(χ′′) is shifted to higher temperatures after post-annealing in an air atmosphere, which is
evidence of enhanced intergrain coupling promoted by oxygen diffusion. Enhanced
intergranular coupling and flux pinning is observed in nitrogen and oxygen post-annealed
samples in field AC susceptibility measurements.
1233
T Oka, Y Hirose, H Kanayama, H Kikuchi, S Fukui, J Ogawa, T Sato and M Yamaguchi
Two types of strong magnetic field generator have been newly constructed by using
superconducting bulk magnets that mainly consist of rare earth 123 single domain compounds
(REBa2Cu3Oy) in conjunction with different kinds of compact cryocoolers. The magnetic flux densities in
the open space outside the vacuum chambers that contain bulk magnets have reached
3.37 T and 2.78 T when a Gifford–McMahon (GM) cryocooler and a Stirling-cycle (ST)
pulse tube cryocooler cooled them to 30.8 K and 62.0 K, respectively. In this study, the
activation of a bulk magnet was accomplished by field cooling magnetization using the
static field of a 5 T superconducting solenoid magnet. It was clarified that the trapped field
distributions strongly reflect the temperature dependence of superconducting properties of
the bulk magnet. The conditions for supplying intense fields in the open space are
discussed to utilize them in practical applications. The most characteristic feature
of superconducting bulk magnets is defined as a compact and strong magnetic
field generator, which is discussed on the map from the industrial point of view.
1239
D Y Jeong, Y H Kim, P M Shirage, S Y Kim, S Horiuchi and J H Lee
The present study shows general characteristic features of processes such as electrodeposition,
drying, and heat-treatment, involved in the preparation of bufferless Tl-1223/Ag
superconducting coated conductors by using an electrodeposition method, the details of
which have not been reported in the literature. The importance of the present study,
however, lies in a new process to make a thick Tl-1223 superconducting layer by using
electrodeposition. In the new method, a relatively thin Tl-1223 precursor film is firstly
electrodeposited on an Ag sheet, dried, and then heat-treated for phase transformation to
superconducting phases to assign conductivity to the film. Then Tl-1223 precursor film is
electrodeposited again on the heat-treated superconducting film, dried, and heat-treated.
The process of electrodeposition, drying, and heat-treatment can be repeated
many times to prepare a very thick superconducting layer. In the present study, a
2–3 µm
thick Tl-1223 layer was prepared on a
intensified Ag sheet by repeating the process once. Even though
Jc
values in thick Tl-1223/Ag were quite low mainly due to material loss during
heat-treatment, the microstructure analysis indicated that Tl-1223 layers were epitaxially
grown on the
intensified Ag sheets provided that the Ag surfaces were flat and clean.
CORRIGENDUM
1253
The following article is Free article
A Stenvall, A Korpela, J Lehtonen and R Mikkonen
There are errors in equations (10) and (22) of the above paper. These errors were only in the formulation of the model in the paper and not in the computations used to obtain the results. Please see the PDF file for full details.
RETRACTION
1254
The following article is Free article
Aditya M Vora
This paper has been retracted by IOP Publishing. Most of the contents of this paper have been previously published in another journal (A M Vora 2007 Physica C 458 43–50). The publisher therefore advises that the paper should not be referenced or used as a basis for future work.
1255
The PDF file provided contains web links to all articles in this volume.