Highlights of 2016

Here, we compared 3D-printed polycaprolactone/poly(lactic-co-glycolic acid)/β-tricalcium phosphate (PCL/PLGA/β-TCP) membranes with the widely used collagen membranes for guided bone regeneration (GBR) in beagle implant models. For mechanical property comparison in dry and wet conditions and cytocompatibility determination, we analyzed the rate and pattern of cell proliferation of seeded fibroblasts and preosteoblasts using the cell counting kit-8 assay and scanning electron microscopy. Osteogenic differentiation was verified using alizarin red S staining. At 8 weeks following implantation in vivo using beagle dogs, computed tomography and histological analyses were performed after sacrifice. Cell proliferation rates in vitro indicated that early cell attachment was higher in collagen than in PCL/PLGA/β-TCP membranes; however, the difference subsided by day 7. Similar outcomes were found for osteogenic differentiation, with approximately 2.5 times greater staining in collagen than PCL/PLGA/β-TCP, but without significant difference by day 14. In vivo, bone regeneration in the defect area, represented by new bone formation and bone-to-implant contact, paralleled those associated with collagen membranes. However, tensile testing revealed that whereas the PCL/PLGA/β-TCP membrane mechanical properties were conserved in both wet and dry states, the tensile property of collagen was reduced by 99% under wet conditions. Our results demonstrate in vitro and in vivo that PCL/PLGA/β-TCP membranes have similar levels of biocompatibility and bone regeneration as collagen membranes. In particular, considering that GBR is always applied to a wet environment (e.g. blood, saliva), we demonstrated that PCL/PLGA/β-TCP membranes maintained their form more reliably than collagen membranes in a wet setting, confirming their appropriateness as a GBR membrane.

We previously developed a biomaterial scaffold that could effectively provide seed cells to a lesion cavity resulting from traumatic brain injury. However, we subsequently found that few transplanted human umbilical cord mesenchymal stem cells (hUC-MSCs) are able to migrate from the scaffold to the lesion boundary. Stromal derived-cell factor-1α and its receptor chemokine (C-X-C motif) receptor (CXCR)4 are chemotactic factors that control cell migration and stem cell recruitment to target areas. Given the low expression level of CXCR4 on the hUC-MSC membrane, lentiviral vectors were used to generate hUC-MSCs stably expressing CXCR4 fused to green fluorescent protein (GFP) (hUC-MSCs^CXCR4/GFP). We constructed a scaffold in which recombinant human brain-derived neurotrophic factor (BDNF) was linked to chitosan scaffolds with the crosslinking agent genipin (CGB scaffold). The scaffold containing hUC-MSCs^CXCR4/GFP was transplanted into the lesion cavity of a rat brain, providing exogenous hUC-MSCs to both lesion boundary and cavity. These results demonstrate a novel strategy for inducing tissue regeneration after traumatic brain injury.

Successful bone tissue engineering requires at the minimum sufficient osteoblast progenitors, efficient osteoinductive factors, and biocompatible scaffolding materials. We previously demonstrated that bone morphogenetic protein 9 (BMP9) is one of the most potent factors in inducing osteogenic differentiation of mesenchymal stem cells (MSCs). Here, we investigated the potential use of a biodegradable citrate-based thermosensitive macromolecule, poly(polyethyleneglycol citrate-co-N-isopropylacrylamide) (PPCN) mixed with gelatin (PPCNG) as a scaffold for the delivery of BMP9-stimulated MSCs to promote localized bone formation. The addition of gelatin to PPCN effectively enhanced the cell adhesion and survival properties of MSCs entrapped within the gel in 3D culture. Using the BMP9-transduced MSC line immortalized mouse embryonic fibroblasts (iMEFs), we found that PPCNG facilitated BMP9-induced osteogenic differentiation of iMEFs in vivo and promoted the formation of well-ossified and vascularized trabecular bone-like structures in a mouse model of ectopic bone formation. Histologic evaluation revealed that vascularization of the bony masses retrieved from the iMEFs  +  PPCNG group was significantly more pronounced than that of the direct cell injection group. Accordingly, vascular endothelial growth factor (VEGF) expression was shown to be significantly higher in the bony masses recovered from the iMEFs  +  PPCNG group. Taken together, our results suggest that PPCNG may serve as a novel biodegradable and injectable scaffold and carrier for gene and cell-based bone tissue engineering.

Membranes for guided bone regeneration (GBR) were prepared from the synthetic biodegradable polymer poly-D,L-lactic/glycolic acid (PLGA). This GBR membrane has a bi-layered structure with a dense film to prevent gingival fibroblast ingrowth and ensure mechanical function, and a micro-fibrous layer to support colonization by osteogenic cells and promote bone regeneration. Hydrolysis and biodegradation were both studied in vitro through soaking in phosphate buffered saline (PBS) and in vivo by implantation in the subcutis of rats for 4, 8, 16, 26, 48 and 52 weeks. Histology revealed an excellent colonization of the micro-fibrous layer by cells with a minimal inflammatory reaction during resorption. GBR using the synthetic PLGA membrane was evaluated on critical-size calvaria defects in rats for 4 and 8 weeks. Radiographs, micro-computed tomography and histology showed bone regeneration with the PLGA membrane, while the defects covered with a collagen membrane showed a limited amount of mineralized bone, similar to that of the defect left empty. The biofunctionality of the PLGA membranes was also compared to collagen membranes in mandible defects in rabbits, associated or not with beta-tricalcium phosphate granules. This study revealed that the bi-layered synthetic membrane made of PLGA was safer, more biocompatible, and had a greater controlled resorption rate and bone regeneration capacity than collagen membranes. This new PLGA membrane could be used in pre-implantology and peri-odontology surgery.

Sufficient vascularization of the implant construct is required for tissue regeneration to ensure the supply of oxygen and nutrients. In our previous work, we established sonication-induced silk fibroin hydrogel to load neural stem cells for brain tissue engineering applications. In this study, we explored the application of silk fibroin as an injectable hydrogel for vascularization of soft tissues. We investigated the ability of outgrowth endothelial cells (OECs) in mono-culture or in co-culture with human bone marrow-derived mesenchymal stem cells (BM-MSCs) to form capillary networks in silk fibroin hydrogels. Furthermore, the silk fibroin hydrogel was modified with IKVAV peptide revealing a sequence derived from the extracellular matrix component laminin-1 to test its effects on angiogenesis, using unmodified and VVIAK modified silk fibroin hydrogel as controls. In monocultures of OECs, no angiogenic structures were observed in silk fibroin hydrogels. In contrast, vascular structures were abundant and increased in co-culture, as confirmed by immunocytochemistry and scanning electron microscopy (SEM) over 10 d of culture in silk fibroin-based hydrogels. Although no significant differences in angiogenic activity seem to be caused by the IKVAV peptide in our experimental settings, these results indicate that sonication-induced silk fibroin-based hydrogels support the formation of functional endothelial tubes and vascularization networks in the presence of mesenchymal cells supporting the vascular sprouting of endothelial cells.

The in vivo function and phenotype of ovarian follicle cells are determined by many factors. When these cells are removed from the in vivo microenvironment and grown in a 2D in vitro environment, the function of the follicular cells is difficult to preserve. A collagen hydrogel was used to examine the hormone and oocyte maturation of ovary follicles in a 3D culture system. Ovarian follicles from rats were isolated and cultured in various concentration of type I collagen hydrogels ranging from 1% to 7% (weight/volume). Differences in cell survival, follicle growth and development, sex hormone production, and oocyte maturation were seen with the modifications in the collagen hydrogel density and elasticity. The results show the significance of the collagen hydrogel properties on phenotype and function maintenance of the ovarian follicles in a 3D culture system.

Human induced pluripotent stem cells (hiPSCs), human embryonic stem cells (hESCs) and human umbilical cord mesenchymal stem cells (hUCMSCs) are exciting cell sources for use in regenerative medicine. There have been no reports on long hydrogel fibers encapsulating stem cells inside an injectable calcium phosphate cement (CPC) scaffold for bone tissue engineering. The objectives of this study were: (1) to develop a novel injectable CPC construct containing hydrogel fibers encapsulating cells for bone engineering, and (2) to investigate and compare cell viability, proliferation and osteogenic differentiation of hiPSC-MSCs, hESC-MSCs and hUCMSCs in injectable CPC. The pastes encapsulating the stem cells were fully injectable under a small injection force, and the injection did not harm the cells, compared with non-injected cells (p  >  0.1). The mechanical properties of the stem cell–CPC construct were much better than those of previous injectable polymers and hydrogels for cell delivery. The hiPSC-MSCs, hESC-MSCs and hUCMSCs in hydrogel fibers in CPC had excellent proliferation and osteogenic differentiation. All three cell types yielded high alkaline phosphatase, runt-related transcription factor, collagen I and osteocalcin expression (mean  ±  SD; n  =  6). Cell-synthesized minerals increased substantially with time (p  <  0.05), with no significant difference among the three types of cells (p  >  0.1). Mineralization by hiPSC-MSCs, hESC-MSCs and hUCMSCs in CPC at 14 d was 13-fold that at 1 d. In conclusion, all three types of cells (hiPSC-MSCs, hESC-MSCs and hUCMSCs) in a CPC scaffold showed high potential for bone tissue engineering, and the novel injectable CPC construct with cell-encapsulating hydrogel fibers is promising for enhancing bone regeneration in dental, craniofacial and orthopedic applications.

Electrospun nonwovens have been used extensively for tissue engineering applications due to their inherent similarities with respect to fibre size and morphology to that of native extracellular matrix (ECM). However, fabrication of large scaffold constructs is time consuming, may require harsh organic solvents, and often results in mechanical properties inferior to the tissue being treated. In order to translate nonwoven based tissue engineering scaffold strategies to clinical use, a high throughput, repeatable, scalable, and economic manufacturing process is needed. We suggest that nonwoven industry standard high throughput manufacturing techniques (meltblowing, spunbond, and carding) can meet this need. In this study, meltblown, spunbond and carded poly(lactic acid) (PLA) nonwovens were evaluated as tissue engineering scaffolds using human adipose derived stem cells (hASC) and compared to electrospun nonwovens. Scaffolds were seeded with hASC and viability, proliferation, and differentiation were evaluated over the course of 3 weeks. We found that nonwovens manufactured via these industry standard, commercially relevant manufacturing techniques were capable of supporting hASC attachment, proliferation, and both adipogenic and osteogenic differentiation of hASC, making them promising candidates for commercialization and translation of nonwoven scaffold based tissue engineering strategies.

Biomaterial scaffolds have been a foundational element of the tissue engineering paradigm since the inception of the field. Over the years there has been a progressive move toward the rational design and fabrication of bio-inspired materials that mimic the composition as well as the architecture and 3D structure of tissues. In this review, we chronicle advances in the field that address key challenges in tissue engineering as well as some emerging applications. Specifically, a summary of the materials and chemistries used to engineer bio-inspired 3D matrices that mimic numerous aspects of the extracellular matrix is provided, along with an overview of bioprinting, an additive manufacturing approach, for the fabrication of engineered tissues with precisely controlled 3D structures and architectures. To emphasize the potential clinical impact of the bio-inspired paradigm in biomaterials engineering, some applications of bio-inspired matrices are discussed in the context of translational tissue engineering. However, focus is also given to recent advances in the use of engineered 3D cellular microenvironments for fundamental studies in cell biology, including photoresponsive systems that are shedding new light on how matrix properties influence cell phenotype and function. In an outlook for future work, the need for high-throughput methods both for screening and fabrication is highlighted. Finally, microscale organ-on-a-chip technologies are highlighted as a promising area for future investment in the application of bio-inspired microenvironments.

Responsive surfaces: a review of the dependence of protein adsorption on the reversible volume phase transition in stimuli-responsive polymers. Specifically addressed are a widely studied subset: thermoresponsive polymers. Findings are also generalizable to other materials which undergo a similarly reversible volume phase transition. As of 2015, over 100 000 articles have been published on stimuli-responsive polymers and many more on protein–biomaterial interactions. Significantly, fewer than 100 of these have focused specifically on protein interactions with stimuli-responsive polymers. These report a clear trend of increased protein adsorption in the collapsed state compared to the swollen state. This control over protein interactions makes stimuli-responsive polymers highly useful in biomedical applications such as wound repair scaffolds, on-demand drug delivery, and antifouling surfaces. Outstanding questions are whether the protein adsorption is reversible with the volume phase transition and whether there is a time-dependence. A clear understanding of protein interactions with stimuli-responsive polymers will advance theoretical models, experimental results, and biomedical applications.

Decellularization is the process of removing the cellular components from tissues or organs. It is a promising technology for obtaining a biomaterial with a highly preserved extracellular matrix (ECM), which may also act as a biological scaffold for tissue engineering and regenerative therapies. Decellularized products are gaining clinical importance and market space due to their ease of standardized production, constant availability for grafting and mechanical or biochemical superiority against competing clinical options, yielding clinical results ahead of the ones with autografts in some applications. Current drawbacks and limitations of traditional treatments and clinical applications can be overcome by using decellularized or acellular matrices. Several companies are leading the market with versatile acellular products designed for diverse use in the reconstruction of tissues and organs. This review describes ECM-based decellularized and acellular products that are currently in use for different branches of clinic.